Char-Broil TRU-Infrared 463251012 Product Manual
  1. Manuals
  2. Brands
  3. Char-Broil Manuals
  4. Grill
  5. TRU-Infrared 463251012
  6. Product manual

Char-Broil TRU-Infrared 463251012 Product Manual

Hide thumbs

Advertisement

Table of Contents

IMPORTANT: Refer to the
instructions inside when
converting this grill to
Natural Gas.
© 2011 Char-Broil, LLC Columbus, GA 31902
PRODUCT GUIDE
MODEL 463251012
T-47D
IMPORTANT: Fill out the product record information below.
Serial Number
Date Purchased
For support and to register your
grill, please visit us at
www.charbroil.com
If you have questions or need
assistance during assembly,
please call 1-888-430-7870.
Printed in China
See rating label on grill for serial number.
Assembly instructions © 2011
08/23/11 • G521-001-030801

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TRU-Infrared 463251012 and is the answer not in the manual?

Questions and answers

Related Manuals for Char-Broil TRU-Infrared 463251012

Summary of Contents for Char-Broil TRU-Infrared 463251012

  • Page 1 If you have questions or need assistance during assembly, please call 1-888-430-7870. IMPORTANT: Refer to the instructions inside when converting this grill to Natural Gas. © 2011 Char-Broil, LLC Columbus, GA 31902 Assembly instructions © 2011 Printed in China 08/23/11 • G521-001-030801...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS DANGER For Your Safety ........2-3 If you smell gas: Use and Care .
  • Page 3 WARNING CAUTION CALIFORNIA PROPOSITION 65 Using pots larger than 6 quarts in capacity could exceed weight limit of the 1. Combustion by-products produced when using this product contain chemicals known to the State of side burner shelf California to cause cancer, birth defects, and other or side shelf, reproductive harm.

  • Page 4: Use And Care

    LP Cylinder USE AND CARE •The LP cylinder used with your grill must meet the following requirements: DANGER •Use LP cylinders only with these required measurements: 12" (30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) capacity maximum. •...

  • Page 5: For Your Safety

    LP Cylinder Exchange Connecting Regulator to the LP Cylinder •Many retailers that sell grills offer you the option of replacing 1.LP cylinder must be properly secured onto grill. (Refer to your empty LP cylinder through an exchange service. Use only assembly section.) those reputable exchange companies that inspect, precision fill, 2.Turn all control knobs to the OFF position.
  • Page 6 Leak Testing Valves, Hose and Regulator 1.Turn all grill control knobs to OFF. 2.Be sure regulator is tightly connected to LP cylinder. 3.Completely open LP cylinder valve by turning hand wheel counterclockwise. If you hear a rushing sound, turn gas off immediately.
  • Page 7 Safety Tips WARNING  Before opening LP cylinder valve, check the coupling nut for tightness.  When grill is not in use, turn off all control knobs and LP For Safe Use of Your Grill and to Avoid Serious cylinder valve. ...
  • Page 8 Burner Flame Check WARNING •Remove cooking grates and troughs. Light burners, rotate knobs from . You should see a smaller flame in Turn controls and gas source or tank OFF when not position than seen on . Perform burner flame check in use.

  • Page 9: Spider Alert

    Cleaning the Burner Assembly CAUTION Follow these instructions to clean and/or replace parts of burner assembly or if you have trouble igniting grill. 1. Turn gas OFF at control knobs and LP cylinder. SPIDER ALERT! 2. Remove cooking grates and troughs. 3.

  • Page 10: Limited Warranty

    LIMITED WARRANTY This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated below beginning on the date of purchase*.

  • Page 11: Parts List

    PARTS LIST Key Qty Description Key Qty Description TOP LID WARMING RACK LOGO PLATE, W/ TEMP GAUGE COOKING GRATE HANDLE END, TOP LID SIDEBURNER SHELF CONTROL PANEL, LEFT SIDE HANDLE, TOP LID SHELF RUBBER BUMPER, RECTANGLE, F/ TOP LID DRIP PAN INSERT RUBBER BUMPER, ROUND LID, F/ SIDEBURNER HARDWARE F/ TOP LID ASSEMBLY...

  • Page 12: Parts Diagram

    PARTS DIAGRAM DD DD EE EE...

  • Page 13: Assembly

    ASSEMBLY Place bottom shelf upside down. Insert Caster Pin into the caster mounting plate to lock it in place, shown A. Spin the caster clockwise into the threads on the bottom shelf until secure. Remove the Caster Pin and repeat for remaining casters.
  • Page 14 Place lower back panel between side panels at rear of bottom shelf, oriented as shown. Secure lower back panel to side panels using two 1/4-20x1/2” screws on each side. Secure lower back panel to bottom shelf using one 1/4-20x1/2” screw. 1/4-20x1/2”...
  • Page 15 Attach center cart divider to bottom shelf using three #10-24x3/8” screws, 5mm lock washers and 5mm flat washers. #10-24x3/8” screw 5mm lock washer 5mm flat washer On back of grill, attach center cart divider to lower back panel using two #8x3/8” self-tapping screws. #8x3/8”...
  • Page 16 Attach cabinet shelf to center cart divider using two #10-24x3/8” screws, 5mm lock washers and 5mm flat washers. Attach cabinet shelf to cart left side panel using two #10-24x3/8” screws, 5mm lock washers and 5mm flat washers. Cabinet shelf 5mm lock 5mm flat washer washer...
  • Page 17 Insert tank heat shield tabs (w/o holes) into slots between upper back panel and lower back panel. Insert front brace between cart side panels. Orient the front brace with the door hinge pin on the top right side. Secure using one 1/4-20x1½” screw on each side. Hinge pin 1/4-20x1½”...
  • Page 18 This step requires two people to lift and position grill head onto cart. Carefully lower the grill head onto the cart, aligning slots at bottom of grill head with posts on cart side panels. Make sure the regulator hose is hanging outside the cart. Grill head must face open side of cart. Grill head Regulator hose Secure front brace in upper hole with one 1/4-20x1½”...
  • Page 19 Inside of the cart, connect the wires from burner electrodes into the back of Electronic Ignition module. Total (5) connections. Connect the two wires [(a) and (b)] from switch wiring harness into the back of Electronic Ignition module. Total (2) connections, shown A.
  • Page 20 Attach right side shelf to firebox using two 1/4-20x3/4” screws and 1/4” nuts, shown A. Attach front of shelf using two #8x3/8” self-tapping screws and large flat washers, shown B. Attach rear of shelf using one 1/4-20x1½” screw, shown C. 1/4-20x3/4”...
  • Page 21 Attach left side control panel to left side shelf using four #10-24x3/8” screws, 5mm lock washers, 5mm flat washers, shown A. Attach side burner lid handle to side burner lid using two #10-24x3/8” screws, 5mm lock washers and 5mm flat washers, shown B.
  • Page 22 Attach left side shelf to firebox using two 1/4-20x3/4” screws and 1/4” nuts, shown A. Attach front of shelf using two #8x3/8” self-tapping screws and large flat washers, shown B. Attach rear of shelf using one 1/4-20x1½” screw, shown C. 1/4-20x3/4”...
  • Page 23 First, remove the two screws and lock washers attached to the sideburner valve bracket. Position sideburner valve bracket beneath sideburner control panel so that valve stem comes through larger center hole in control panel. Align the holes on valve bracket with left and right holes on control panel. Secure using lock washers and screws that were removed from bracket.
  • Page 24 Place side burner cooking grate onto side burner shelf. Insert the pin on bottom of door into hole in bottom shelf. Press upper hinge pin in front brace, align hinge hole on top of door, and release hinge pin into door. PRESS Top of door...
  • Page 25 Attach left small doors to left side panel using eight #8-32x1/4” screws. Place trough middle bracket into fire box. Place troughs into fire box. Align pins at front of troughs with the holes at front of fire box. Troughs Put trough middle bracket on the brackets at front and rear of firebox.
  • Page 26 Place cooking grates onto firebox as shown. Insert the four wire ends at rear of warming rack into holes in back of fire box. Front wires of warming rack rest on sides of firebox. Assembled warming rack Warming Rack Cooking grate LP CYLINDER IS SOLD SEPARATELY.

  • Page 27: Conversion Instructions

    Consumer must purchase Natural Gas Conversion Kit 4584625 to convert this grill to natural gas. Use the following instructions instead of instructions found in conversion kit Main Burner Conversion Make sure all Control Knobs are in the OFF position, LP Tank Valve is closed, Tank is disconnected from Regulator and removed from Grill.
  • Page 28 Pull the Burner Control Knobs off of Valve Stems. Remove Screws and Washers that secure each Bezel to the Control Panel. Save removed Bezels for converting back to LP Tank Gas. Install new Natural Gas Bezels provided with Kit (see illustration below) in place of old Bezels, on Control Panel and secure using previously removed Screws and Washers.
  • Page 29 Sideburner Conversion Open Sideburner lid and remove the Sideburner Grate. Beneath Sideburner shelf, remove Wingnut. Remove Sideburner from shelf. Sideburner Grate Sideburner Wingnut Using the provided Orifice Removal Tool, unscrew the Orifice from the end of the Sideburner Valve. Save removed Orifice and Orifice Removal Tool for converting back to LP Tank Gas.
  • Page 30 Pull the Sideburner Control Knob off of Valve Stem. Remove the existing Bezel by removing the two Screws and Washers securing Bezel to shelf control panel. Save removed Bezel for converting back to LP Tank Gas. Install new natural gas Bezel (see illustration below) and press Control Knob back onto Valve Stem. Screws Bezel Natural Gas Bezel...
  • Page 31 Outdoor Stove & Griddle Conversion Open Sideburner lid and remove the Sideburner Gate. Beneath Sideburner shelf, remove Wingnut. Remove Sideburner from shelf. Sideburner Grate Wingnut Sideburner Using the provided Orifice Removal Tool, unscrew the Orifice from the end of the Sideburner Valve. Save removed Orifice and Orifice Removal Tool for converting back to LP Tank Gas.
  • Page 32 Pull the Sideburner Control Knob off of Valve Stem. Remove the existing Bezel by removing the two Screws and Washers securing Bezel to shelf control panel. Save removed Bezel for converting back to LP Tank Gas. Install new natural gas Bezel (see illustration below) and press Control Knob back onto Valve Stem. Screws Bezel Natural Gas Bezel...
  • Page 33 Natural Gas Hose Conversion Using a wrench, not provided, remove LP Regulator Hose Assembly from Manifold Connection. Save removed LP Manifold Connection for converting back to LP Tank Gas. Your Grill may differ from illustration shown. Manifold Connection LP Regulator Hose Assembly Manifold Connection Natural Gas Hose Assembly...
  • Page 34 4. When the quick disconnect socket and the gas hose are connected, WARNING a valve in the socket opens automatically to permit full gas flow. When the gas hose is disconnected, the valve in the socket instantly and positively shuts off the flow of gas. Because the valve in the Do not use hard metal piping of any kind to connect this socket positively shuts off the flow of gas, the grill can be type of grill to natural gas source.

  • Page 35: Troubleshooting

    DANGER: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Emergencies Possible Cause Prevention/Solution Gas leaking from • Damaged hose. • Turn off gas at LP cylinder or at source on natural gas systems. If cracked/cut/burned anything but burned, replace valve/hose/regulator.
  • Page 36 Troubleshooting (continued) Problem Possible Cause Prevention/Solution Burner(s) will not light ELECTRONIC IGNITION: using ignitor. • No spark, no ignition noise. • See Section I of Electronic Ignition System. (See Electronic Ignition Troubleshooting also) • No spark, some ignition noise. • See Section II of Electronic Ignition System. •...
  • Page 37 Troubleshooting - Electronic Ignition Problem (Ignition) Possible Cause Check Procedure Prevention/Solution SECTION I No sparks appear at • Battery not installed • Check battery orientation. • Install battery (make sure that “+” and “–” any electrodes when properly. connectors are oriented correctly, with “+” end up Electronic Ignition Button and “–”...
  • Page 38 NOTES...

This manual is also suitable for:

Tru-infrared t-47d

Table of Contents

Save PDF