Boss Audio Systems GT-100 Owner's Manual page 38

Pedal Settings (Control/Expression)
Parameter Value
0–100, BPM
–
When set to BPM, the value of each parameter will
be set according to the value of the "Master BPM"
WAVE RATE
[7]
specified for each patch. This makes it easier to
*1
achieve effect sound settings that match the tempo
of the song.
* If, due to the tempo, the time is longer than the
range of allowable settings, it is then synchro-
nized to a period either 1/2 or 1/4 of that time.
SAW
WAVEFORM
[8] TRI
*1
SINE
Page 4
PATCH CHANGE
EXP PDL-LO
EXP PDL-MID
EXP PDL-HI
EXP PDL SW
P.LOOP PEDAL
INT PDL
[5] TRIGGER
ACC/CTL PDL
*2
SUB EXP PDL
SUB CTL1 PDL
SUB CTL2 PDL
CC#1–#31
CC#64–#95
INT PDL TIME
[6] 0–100
*2
LINEAR
INT PDL
[7] CURVE SLOW RISE
*2
FAST RISE
*1 The WAVE RATE and WAVEFORM parameters are enabled when the
Source parameter is set to WAVE PEDAL.
*2 The INT PDL TRIGGER, INT PDL TIME, and INT PDL CURVE parameters are
enabled when the SOURCE parameter is set to INT PEDAL.
38
Explanation
This determines the time spend
for one cycle of the assumed EXP
Pedal.
This is activated when a patch is
selected.
This is activated when the GT-100's
[EXP] pedal is set to the minimum
position.
This is activated when the GT-100's
[EXP] pedal is moved through the
middle position.
This is activated when the GT-100's
[EXP] pedal is set to the maximum
position.
This is activated when the EXP
pedal switch is operated.
This is activated when the
[PHRASE LOOP] pedal is operated.
This is activated when the [ACCEL/
CTL] Pedal is operated.
This is activated when an external
expression pedal connected to
the SUB CTL 1, 2/SUB EXP jack is
operated.
This is activated when an external
footswitch connected to the SUB
CTL 1, 2/SUB EXP jack is operated.
This is activated when an external
footswitch connected to the SUB
CTL 1, 2/SUB EXP jack is operated.
This is activated when a control
change is received.
This is activated when a control
change is received.
This specifies the time over which
the internal pedal will move from
the toe-raised position to the
toe-down position.
About the Range of a Target's Change
The value of the parameter selected as the target changes
within the range defined by "Min" and "Max, " as set on the
GT-100.
When using an external footswitch, or other controller that
acts as an on/off switch, "Min" is selected with Off (CLOSED),
and "Max" is selected with On (OPEN).
When using an external expression pedal or other controller
that generates a consecutive change in the value, the value
of the setting changes accordingly, within the range set by
the minimum and maximum values. Also, when the target
is of an on/off type, the median value of the received data is
used as the dividing line in determining whether to switch it
on or off.
When using the footswitch:
MAX
MIN
OFF
When using the expression pedal:
MAX
MIN
0
When the pedal is
fully raised
When controlling the On/Off target with the expression pedal:
Value
ON
OFF
0
When the pedal is When the pedal
fully raised is advanced
halfway
* The range that can be selected changes according to the
target setting.
* When the "minimum" is set to a higher value than the
"maximum, " the change in the parameter is reversed.
* "The values of settings can change if the target is changed
after the "minimum" and "maximum" settings have been
made. If you've changed the target, be sure to recheck the
"minimum" and "maximum" settings.
ON
127
When the pedal is
fully advanced
Degree to
Which Expres-
sion Pedal Is
Depressed
127
When the pedal
is fully advanced