General Information - Electrolux thermaline S90 Installation And Operating Instructions Manual

I .

GENERAL INFORMATION

1. INSTRUCTIONS FOR SAFETY AND USE
1.1 INSTALLATION AND INITIAL OPERATION
The installation, adjustment and initial opera-
tion of the appliance must be carried out
according to the manufacturer's instructions
and may only be done by an authorised spe-
cialist.
Installations for the supply of electricity and
gas must be carried out by approved special-
ists in compliance with specific national and
local regulations. They bear the responsibil-
ity.
The installation must conform with local
codes, or in the absence of local codes, with
the National Fuel
Z223.1/NFPA 54, or the Natural Gas and
Propane Installation Code, CSA B1 49.1.
The appliance and its individual shutoff valve
must be disconnected from the gas supply
piping system during any pressure testing of
that system at pressures in excess of 1/2 psi
(3.5 kPA).
The appliance must be isolated from the gas
supply piping system by closing its individual
manual shutoff valve during any pressure
testing of the gas supply piiping system at
test pressures equal to or less than 1/2 psi
(3.5 kPA).
The appliance must not be placed in
operation until the user has become familiar
with its operation. The operating instructions
and the related safety precautions must be
followed precisely.
attention and warning label indications on the
appliances.
1.2 OPERATOR'S OBLIGATIONS
The manager is responsible for ensuring that
all components relevant to safety are in per-
fect working order at all times. The operating
condition of these components must be
examined by an authorised specialist at least
once a year and any defects remedied if
required.
The operator of this appliance is responsible
for total observation of the national regula-
tions concerning operating safety.
Remain the manual for future reference.
1.3 USE AS PRESCRIBED
Closed containers (jars, cans, bottles, tubes,
etc.) must not be heated owing to the danger
of bursting and injuries.
1.4 SAFETY-CONSCIOUS WORKING
Touching the hot cooking zones can cause
burns.
Overheated oil can ignite spontaneously.
Never use water to extinguish burning oil, but
smother the flames with the lid or a damp
cloth.
Touching the hot cooking zones can cause
burns.
62.9678.01_UL
GENERAL INFORMATION
Gas Code, ANSI
Follow strictly the
Overheated oil can ignite spontaneously.
Never use water to extinguish burning oil, but
smother the flames with the lid or a damp
cloth.
The escape of burnable gases represents a
fire and explosion hazard. Action in the case
of a gas leak and a smell of gas:
- No smoking, no fire
- Do not operate electric switches or bells.
- Do not operate the piezo igniter
- Close gas cylinder valves and the main
gas valve on the appliance.
- Ventilate the room thoroughly
- Place the leaking gas cylinders upright in
the open with valves closed.
The waste-gas outlets of the roasting and
baking oven become hot. Avoid touching
them.
The waste-gas outlets of the roasting and
baking oven are not to be covered by any
objects.
Spraying the appliance or parts of it with a
high-pressure cleaning device may cause
malfunctions and is not to be done.
Keep the appliance area free and clear from
combustibles
Do not obstruct the flow of combustion and
ventilation air.
For appliances with a downpipe, the hose
should lead into a drain opening which is cov-
ered by a grating such that it cannot be
kicked or tipped, or a drain gutter should run
underneath the appliance.
Devices on wheels
configuration must be checked before each
start-up whether the potential equalization is
connected with the neighbour equipment.
The connection may be done only by
authorized technical personnel.
Appliances on wheels must be fastened to
the building.
1.5 AFTER-SALES SERVICE AND REPAIR
In the event of a permanent fault which inter-
feres with operation, the appliance must be
switched off and disconnected from the
power supply.
To perform maintenance and repairs contact
the factory, the factory representative or a
local service company.
Repair, maintenance work and other adjust-
ments are only to be carried out by an
authorised specialist. The valid local and
national regulations must be observed. This
applies especially to burners, ignition, safety
and control elements.
replacement are only to be replaced by origi-
nal spare parts. Periodic tests for gas leaks
must be carried out. A service contract is
therefore recommended.
Cleaning and maintenance must be done
only when the heating surfaces are cold. Do
not use inflammable liquids to clean the
appliance.
An obligatory service check is required
annually.
set up in block
Parts requiring
Page 3