Before installation, park the vehicle in a safe and level place and remove the ignition key. • If using branch connections, it is important to note the relevant cable section. Subject to errors or technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
Radio Optional Earphone Optional Sound system / Antenna GPS/GSM Box OnlinePro loudspeaker Hands-free microphone Reverse signal Power supply Note: Connection options are described in detail on page 57. Subject to errors and technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
If reception is still unsatisfactory after installation, the angle of the antenna to the vehicle can be adjusted to optimise reception. In most cases, best results are achieved with the antenna in a vertical position. Subject to errors or technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
Page 5
The installation of the GSM/GPS antenna on sharply angled windows (i.e. side windows or rear window in estate cars/ stations wagons) is not recommended as satisfactory GPS reception cannot be ensured. Possible antenna positioning Rear window Subject to errors and technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
Page 6
Take the windscreen-wiper range into account when positioning the antenna. The glass surface to which the antenna must adhere, may be slightly curved. When selecting position for installation, please bear in mind the possibility of cable extension. Subject to errors or technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
Page 7
The adhesive foil will adhere immediately to the adhesion surface and cannot be repositioned. It is not possible to reuse the adhesive foil. c. Run connecting cable to the installation position of the GSM/GPS Box. Subject to errors and technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
F (To avoid risk of damage, please pay attention to screw length). Subsequently, affix the microphone to the screw-on plate G with the adhesive strip E. The connection of the hands-free microphones takes place in socket C of the OnlinePro. Subject to errors or technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
Page 9
Once the contacts are inserted into the blue plug housing, a special tool is required to remove them. Connection of the blue plug housing Socket C Colour Function White Yellow Earth Socket C3 Subject to errors and technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
The GSM/GPS Box should be installed in such a way that the SIM card inserted into the SIM card holder can be taken out without having to remove the GSM/GPS Box. Subject to errors or technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
Page 11
Subsequently, press the SIM card insertion slot back down and push in GSM/GPS Box the opposite direction of the arrow. Close the retaining cover A. Older SIM cards (5 Volt technology) cannot be used. Please consult your network provider. Subject to errors and technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
Page 12
Connect the GSM/GPS antenna plugs to the sockets D and E on the GSM/GPS Box. • Connect the optional telephone handset (if available) to socket C of the GSM/GPS Box. Additional earth lead Subject to errors or technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
Low level < 0.3 V, High level 5 V - 16 V If you do not know the exact installation position / location of the speed signal, please consult the vehicle manufacturer. Subject to errors and technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
Page 14
If the sealed speedometer cable is released, a correct display cannot be guaranteed. Incorrect installation leads to improper functioning of the navigation system or of the speedometer. Subject to errors or technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
Page 15
2 x fuel washers 4.0 KN07.0570.18 (VDO part number) 2 x washers KN11.1904.122 (VDO part number) A complete set can also be ordered from VDO (Part number X 39397106191). Subject to errors and technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
Page 16
Connect the union nut and hose sleeve (Figure 6) and push onto the Figure 6 hose ends (Figure 7). • Connect friction washer to dog (Figure 8). Figure 7 Figure 8 Figure 8 Subject to errors or technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
Page 17
Wire connections for the speed sensor Brown earth (terminal 31) Black power supply (terminal 15), 9 - 16V, 30 mA Blue/red - signal for socket A pin 1 Subject to errors and technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
Fig. D and subsequently adjust as shown in Fig. E (Gently press slide in the direction of 1 while at the same time moving the slide in the direction of 2). Subject to errors or technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
With some languages, a selection can be made between male and female voices. With the right rotary control , select voice. The voice is accepted and installed by pressing the control. Subject to errors and technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
After commissioning, a calibration journey is required. During this journey, the speedometer signal (GAL) is adapted to the vehicle- specific data, and the gyro-sensor to the unit installation position. Subject to errors or technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
Page 21
Re-installation can be skipped by pressing the key. • For correct navigation on routes with time-dependent traffic guidance, the time should be correctly set as described under "System settings" in the operation guide. Subject to errors and technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
- Setting of the Demo mode • Route mode - Starting the Route-mode function By turning the right rotary control , select the desired entry (upper- case letters) and press to confirm. Subject to errors or technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
Page 23
Drive round a bend to test the function of the internal sensors. The value behind must change. Gyro: • To exit the Sensor Test, press the right rotary control . The unit switches back to the Service Mode. Subject to errors and technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
Page 24
(do not move the vehicle during this period). • To exit the GPS Test, press the right rotary control . The unit switches back to the Service Mode. Subject to errors or technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
Page 25
(i.e. ) are displayed. After calibration is completed, instead of , the street currently being driven on is displayed Backwards (provided it is included in the digital map). Subject to errors and technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
Page 26
, the Route Mode is activated. • To end the Route Mode, route guidance must be terminated, as described in the operating guide. Subject to errors or technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
LineOut front right Illumination (terminal 58) Subwoofer LineOut Socket C2 Switched positive (terminal 15) Earth (terminal 31) 7-12 Special connection for Becker CD changer Socket B Socket C3 Loudspeaker rear right + NF - Hands-free microphone Loudspeaker rear right -...
Solution: The most favourable installation position possible should be selected. In the case of all-round heat-reducing gla- zing, an exterior antenna connected via an adapter (optionally available) can be used. Subject to errors or technical changes Copyright by Becker GmbH, D-76303 Karlsbad...
Page 29
Fault: The other party hears an echo during phone calls. Solution: Set the sensitivity of the hands-free microphone (see Operating Guide, under User Menu). In most cases, a setting between 0 and 3 achieves an optimum result. Subject to errors and technical changes Copyright by Becker GmbH, D-76303 Karlsbad...