Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for GReddy Full Auto Timer
Summary of Contents for GReddy Full Auto Timer
- Page 1 Instruction Manual...
- Page 2 Important Please check the list below to make sure you have all of the following parts before you proceed. If you are missing parts please contact the GReddy Authorized Dealer you purchased the unit from. Turbo Timer Power Harness Main Harness 1pc.
- Page 3 4-pin connector of the Turbo Timer. Then connect the black wire with the loop connecter to a good chassis ground.( to steel body) key switch connector Optional GReddy Turbo Timer Harness (sold separately) key cylinder 3-pin connector ground wire.
-
Page 4: Installation Without Optional Turbo Timer Harness
Installation (without Optional Turbo Timer Harness) Follow the key switch to it’s electrical connector, then unplug the harness. Find the appropriate wires with either a factory service manual or a volt meter. (see 2.3 for wiring) Cut off the 3-pin connector on power harness. Then splice and solder the appropriate wires to the power harness. - Page 5 Wiring Diagram The wires coming out form the key switch usually consist of: 12 v - 12 volt constant power - Ignition power ACC - Accessory power - Starter signal Other than these four wires, the vehicle may have two ON wires. Wiring Procedure: Cut the Power harness close to the 3-pin connector Use a volt meter or test light to find the appropriate wires.
-
Page 6: Harness Connections
Harness Connections Parking Brake Feature: Remove the cover over the parking brake and find the parking switch wire(s). (see you factory service manual) * If there is one wire, make sure the wire: shows 0 volts, when the parking brake is engaged. and shows 12 volts, when the parking brake is released. - Page 7 Turbo Timer Functions Back OPTION Switch Used to connect the Remote Switching System (sold separately) Line Switch Display TIME Button (Referred as "T") Used when switching the main modes. Used to change the countdown time and set-up time. SELECT Button (Referred as "S") Used when switching the sub modes.
-
Page 8: Display Description
Display Description Attack Mode indicator. Flashes when Attack timer is activated. Stopwatch Mode indicator. Flashes when the stopwatch is activated. Speed Mode indicator. Displayed while in Battery Mode. Best lap time indicator. Flashes the best lap time during Stopwatch Mode. Count Down Mode indicator. - Page 9 Display Description P+S+T P+S+T P+S+T Count Battery Stopwatch Down Mode Mode Mode Auto Voltage Lo Mode Display Mode Mode Auto Battery Lap Read Hi Mode Warning Mode Lo Mode Preset 1 Battery Split Mode Warning Mode Hi Mode Preset 2 Split Read Mode Mode...
- Page 10 Display Description P+S+T P+S+T P+S+T Attack Speed Setup Mode Mode Mode 0-200m Speedometer Sound Mode Mode Mode 0-400m Mode Speed peek Line Switch Mode Mode 200-400m Mode 0-100km/h Speed Warning RPM Setup Mode Set up Mode Mode 0-200km/h Mode Speedometer Set up 50-100km/h Mode...
- Page 11 Operation Check Parking Brake Safety Feature Operation Check Engage parking brake. Manual Transmission: Place into Neutral Automatic Transmission: Place into Park. Start the engine. Make sure the Turbo Timer powers up with the music and display lights operating. (note: The Turbo Timer may be turned "Off"...
- Page 12 This concludes the check procedures. Timer and engine should trun off. If the Turbo Timer did not power up, or these safety features are not working, please recheck all the wiring connections and then contact your Authorized GReddy Dealer.
- Page 13 Countdown Mode Auto Countdown Mode Auto Timer Mode automatically calculates a suggested count down time for your vehicle, according to your car’s RPM. You may also choose 2 count down time offset ratios "Hi" or "Lo". This will add a preset time to your calculated count down time.
- Page 14 Countdown Mode Preset Mode There are two Preset Countdown mode you can select from. Preset mode can be set from 0 sec. to 9 min 59 sec. by increments of 10 sec. The factory setting is: 1 min. for P-1 3 min.
- Page 15 Battery Mode Battery Voltage Display Mode This feature displays the "real-time" battery voltage. There is a voltage warning feature that can be turned on and off. The warning buzzer and the back light will flash when the voltage exceeds the set voltage. (1) To go to the Battery Mode from Countdown Mode, press P+S+T "Real-time"...
- Page 16 Battery Mode Voltage Warning Display Mode When the Warning is set, the warning buzzer and the back light will flash when the voltage exceeds the set voltage. This feature will only work while in battery mode. (1) Press the P+S button to P-1 is selected here.
- Page 17 Stopwatch Mode Lap Mode This feature can record up to 30 lap times from 0 ~ 9’ 59" 99. Also while recording the time, the best lap will be indicated by "BEST" on the display. (1) Press the P+S+T button to go to Stopwatch Mode.
- Page 18 Stopwatch Mode Lap Read Mode This feature allows the user to look over the recorded lap times. Up to 30 lap time can be recalled one by one. The best lap time will be indicated with "BEST" shown in the display. (1)While in Stopwatch Mode, press the P+S button to go to Lap Read mode.
- Page 19 Stopwatch Mode Split Mode This feature can record up to 10 split times from 0 ~ 9’ 59" 99. Lap time can also be recorded at the same time. (1) While in the Stopwatch mode, press the P+S button to go to 2 sec later, Standby Split Mode.
- Page 20 Stopwatch Mode Split Read Mode This feature allows the user to look over the recorded split times. Up to 10 split time can be recalled one by one in order. Lap time can also be recalled at the same time. (1)While in Stopwatch Mode, press the P+S button to go to Split Read mode.
- Page 21 Attack Mode 0-200m, 0-400m, 200-400m, 0-100km/h, 0-200km/h, 50-1000km/h Mode This feature allows the user to record 0-200m, 0-400m, 200-400m, 0-100km/h, 0-200km/h, 50-1000km/h times. Important! - This feature should only be used on a race track where it is safe. Please never try on the public highways. *This feature requires the wiring of the vehicle speed sensor signal wire.
- Page 22 Attack Mode This shows 0-200m Mode is selected goes to stand-by mode. Countdown start by pressing T button Auto Start by "Beep" Moving the vehicle. "Beep" The timing will start with a "Beep" as soon as the vehicle starts to move. When the vehicle reaches the distance or the speed the mode is set to the timing...
- Page 23 Speed Mode Speedometer Mode This feature allow the user to monitor the "real time" vehicle speed. With use of the Speed Warning feature, buzzer and flashing back light will warn the driver when the speed exceeds the set warning speed. (1) Press the P+S+T button to go to main Speed Mode.
- Page 24 Speed Mode Speed Warning Mode This feature allow the user to set the warning speed to warn the driver when the speed exceeds the set warning speed with a buzzer and flashing back light. *This feature only work while in the Speed Mode (1)While in Speed Mode, press the P+S button to go to Speed Warning Setup mode.
- Page 25 Speed Mode Speedometer Setup Mode This feature allow the user to set the Turbo Timer speedometer to match the vehicle’s speedometer. (1)While in Speed Mode, press the P+S button to go to Speedometer Setup mode. (2)Get the vehicle speed up to 40km/h.
- Page 26 Setup Mode Sound Mode This feature allow the user to turn the sound ON or OFF. (1) While in Setup Mode, press the P+S button to go to Setup 2 sec later. mode. Sud will display indicating Sound Mode. (2) Hold down the T button for 5 sec Hold down the T to turn OFF.
- Page 27 Setup Mode Line Switch Mode This feature is used when the count down does not properly operate. If the engine shuts down when the IG key is turned off with out counting, follow these instructions. (1) While in Setup Mode, press the P+S button to go to Line Switch mode.
- Page 28 Setup Mode RPM Set Mode This feature is used when the Auto Mode does not operate properly or to set the Turbo Timer RPM to match the vehicle’s tachometer. (1) While in Setup Mode, press the P+S button to go to RPM Set mode.