JVC GY-HD200UB - Camcorder - 1080i Owner's Manual page 55

OTHERS
Warnings and Responses (Cont'd)
Error code
Warning
• Warning Indications for VTR Abnormalities
Should malfunctions occur during VTR operation, this
device self-diagnoses the cause and shows the diagnose
together with an error code on the LCD monitor or in the
viewfinder.
Error Code Error Details
0201 Indicates dew formation (condensa-
CONDENSATION ON DRUM tion).
3200 Tape cannot be loaded.
LOADING FAILURE
3300 Tape cannot be unloaded.
UNLOADING FAILURE
4100 Irregularity with eject operation.
CASSETTE EJECT FAILURE
5605 - 5609 Tape is cut.
DEFECTIVE TAPE
5702 Tape end sensor error.
TAPE END DET. ERROR
5802 Tape beginning sensor error.
TAPE BEGIN DET. ERROR
7001 Drum rotation error.
DRUM MOTOR FAILURE
7101 Capstan rotation error.
CAP MOTOR FAILURE
7202 - 7203 Supply reel rotation error.
SUPPLY REEL FAILURE
7302 - 7303 Take up reel rotation error.
TAKE UP REEL FAILURE
7305 Take up reel rotation error when un-
TAKE UP REEL FAILURE loading.
8000 Tape problem detected.
EMERGENCY TAPE!
TURN POWER OFF. System error when power is turned on. HDV/DV LED, VTR indicator
TURN BACK ON LATER.
104
This device Operation Remedy
Operation stops. All opera- Leave this device with the power ON,
tions are rejected. until the indication disappears.
X See page 9.
Switch the power OFF and then switch
it back ON. However, the tape may be
damaged depending on the circum-
stances. Please consult the person in
charge of professional video equip-
ment at your nearest JVC-authorized
service agent.
Operation stops. Press the EJECT button to take out the
cassette.
If the tape runs out during recording,
switch the power OFF and then switch
it back ON, press the EJECT button,
and then take out the cassette.
Operation stops. All opera- Switch the power OFF and then switch
tions are rejected. it back ON. However, the tape may be
damaged depending on the circum-
stances. Please consult the person in
charge of professional video equip-
ment at your nearest JVC-authorized
service agent.
Turn off the power and let this device
and TALLY lamp flash. Only sit for sometime before turning it back
POWER switch operation is on.
accepted.
TALLY lamp
Blinks when remaining battery power or tape is low. (Only
in Camera mode)
Blinking Pattern Remaining Battery/Tape
Slow blinking • Remaining battery power is low.
(once per sec.) • Remaining tape time is equivalent to less
than 3 minutes.
Fast blinking • Tape has run out.
(four times per sec.) • Irregularity has occurred in the VTR.
Alarm Sound
When remaining battery power becomes low, a warning
sound is output from the monitoring loudspeaker and the
PHONES jack.
(In Camera mode only)
When an irregularity occurs in the VTR, a warning sound
is also output.
Whether or not alarm sound should be output and the vol-
ume level are selected with the ALARM VR LEVEL item
on the OTHERS[1/2] menu screen.
Depending on the alarm conditions, the warning indicators
on the LCD monitor/viewfinder screen, the TALLY lamp,
and alarm sounds appear as shown in the following table.
Alarm Indications on LCD Monitor/
TALLY lamp
Viewfinder Screen
VTR alarm indication
(Example)
I
J
I
J
Display symbols J : Blinking once per second.
: Sound interrupted once per second.
Alarm Sound Condition
Dew formation (condensation) or error has oc-
curred in the VTR.
About 3 min. before tape end
(displayed during recording).
Tape end
(displayed during recording).
Remaining battery power is low.
I : Blinking four times per second.
: Continuous sound.
105