CONTENTS Instructions for the User Important Safety Instructions Operation Before use Freezer controls Starting your appliance Temperature control Warning light (red) Temperature acoustic alarm Freezing fresh food Frozen food storage Thawing Ice making Health and safety guidelines Defrosting Maintenance and Cleaning...
¥ Do not remove items from the freezer comparte- ment if your hands are damp/wet, as this could cause skin abrasions or frost/freezer burns. ¥ Bottles and cans must not be placed in the freezer compartment they can burst when the contents freeze.
Servicing ¥ This product should be serviced by an authorised engineer and only genuine spare parts should be used. ¥ Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning.
When the freezer is first switched on, the warning light will stay on until the temperature has dropped to a safe level for the storage of frozen food.
The appliance is provided with a plastic ice cube tray. Fill the tray 3/4 full to allow the ice to expand and place it in the freezer. To turn out the ice cubes simply give the tray a slight twist to release the cubes.
¥ Cool cooked food as quickly as possible but do NOT place in the freezer until cool. (Leave food in a place as cool as possible in order that it can then be placed in the refrigerator as soon as possible).
Important In the event of a power failure causing t h e temperature within your freezer to rise, do not re-freeze the food without checking its condition. The following guidelines should assist you: Ice-cream: once thawed should be discard-ed.
MAINTENANCE AND CLEANING Warning Before any maintenance or cleaning work is carried out, DISCONNECT the appliance from the ELECTRICITY supply. Important This appliance contains hydrocarbons in its cooling unit maintenance and recharging must therefore only be carried out by autho- rised technicians.
Symptom No power to the appliance The temperature in the freezer is too high The freezer door will not open The compressor runs continuously Excessive frost and ice has built up.
“Something Not Working.” CUSTOMER CARE DEPARTMENT For general enquiries concerning your Electrolux appliance or for further information on Electrolux products, please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.electrolux.co.uk...
Standard guarantee conditions We, Electrolux, undertake that if within 12 months of the date of purchase this Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: •...
TECHNICAL SPECIFICATIONS DIMENSIONS POWER SUPPLY VOLTAGE AND FREQUENCY TOTAL POWER ABSORBED AVERAGE DAILY UNITS ELECTRICITY(*) GROSS CAPACITY NET CAPACITY STAR RATING (*)This figure is based on standard test results in accordance with European Standard EN153. Actual con- sumption will depend on how the appliance is used and where it is located. INSTALLATION Positioning This appliance should only be installed at a location...
ELECTRICAL CONNECTION WARNING THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should this safety observed. If the plug that is fitted to your appliance is not suitable for your socket outlet, it must be cut off and the appropriate plug fitted.
BUILDING-IN INSTRUCTIONS Before carrying out any work, remove the plug from the power socket. Grid preparation Left door opening: Remove the left side (A) of the grid cutting it from the rear (see figure). Right door opening: Remove the right side (B) of the grid cutting it from the rear (see figure).
Attention After completion of the door reversing opera- tion, check that the door gasket adheres to the cabinet. If the ambient temperature is cold (i.e. in Winter), the gasket may not fit perfectly to the cabinet. In that case, wait for the natural fit- ting of the gasket or accelerate this process by heating up the part involved with a normal hairdryer on a low setting.
Page 17
3. Two cabinet securing brackets are supplied with the installation pack. They need to be assembled onto the cabinet prior to cabinet being pushed into the Kitchen aperture. - To fit these brackets remove the two screws at the top left and right hand front corners of the cabinet. - Position the two brackets as shown in the figure and replace the two securing screws.
Page 18
7. Screw appliance into place and retain the cabinet with screws through the securing brackets into the worktop or adjacent woodwork as necessary. 8. To mount the furniture door proceed as shown in the figures: clic clic...
Page 19
UPPER PART OF KITCHEN FURNITURE PANEL LOWER PART OF KITCHEN FURNITURE PANEL...
9. Refit the covering strip. Fitting the plinth Important For the efficient operation of the appliance, it is important that the original ventilation grid is used. ¥ For an opening height dimension A=820 mm and a plinth height dimension a=100 mm, the plinth may be fitted without adjustments.