Table of Contents
Advertisement
3.8.1 Direct To-Procedure 1
1. Press D. The Direct To page is displayed on the left
side (figure 3-87). The cursor will already be on the
left page. A waypoint identifier may or may not be dis-
played, it doesn't matter at this point.
2. Rotate the left inner knob to select the first character
of the desired waypoint's identifier (figure 3-88).
Remember to enter the "K", "C", or "P" prefix for
certain airports in North America, if required (see
section 2.3, "USE OF ICAO IDENTIFIERS").
3. Turn the left outer knob one step clockwise to move
the flashing portion of the cursor over the second
character position (figure 3-89).
4. Rotate the left inner knob to select the second charac-
ter of the identifier (figure 3-90).
5. Use the left outer and inner knobs as in the previous
steps until the desired identifier is completely dis-
played (figure 3-91).
6. Press E to display the waypoint page on the right
side for the selected waypoint (figure 3-92). Note: If
an incorrect identifier has been entered, you may
immediately start using the left inner knob to re-enter
the correct identifier.
7. Press E again to approve the displayed waypoint
page. The right side will display the NAV 1 page and
the left side will return to the page which was dis-
played prior to pressing D (figure 3-93). If the Direct
To was started while the NAV 1 page was shown on
the left side, then the left and right pages will revert to
the pages that were shown before the Direct To was
started. The selected waypoint is now the active
Direct To waypoint.
NOTE: In some cases during approach operations, the
KLN 90B presents a page asking how a waypoint is used
when the waypoint identifier is entered character by char-
acter. When this page is presented, simply choose the
desired use of the waypoint (e.g., FAF or MAHP) by mov-
ing the cursor with the left outer knob and pressing
Choosing the correct use of the waypoint is required to
ensure proper waypoint sequencing once the aircraft
reaches the waypoint.
3.8.2 Direct To-Procedure 2
1. Select the desired waypoint page on the right side
(figure 3-94) using one of the three procedures
explained
in section 3.7,
2. Press D. The Direct To page is displayed on the left
side and it contains the desired waypoint identifier (fig-
ure 3-95).
"SELECTING WAYPOINTS".
DIRECT TO: |
K
CRSR
Figure 3-88
DIRECT TO: |
KOAJ
CRSR
Figure 3-90
DIRECT TO: | KOSH
CRSR
PRESENT POS|
LGA
N 41^00.03'|ETE
W 73^41.62'|BRG
NAV 2 enr-leg
PRESENT POS| KOSH
LGA
E.
N 41^00.03'|N 43^59.06'
W 73^41.62'|W 88^33.42'
NAV 2 enr-leg
DIRECT TO: | KOSH
CRSR
3-28
DIRECT TO: |
|
|
K
|
|
|
CRSR
DIRECT TO: |
|
|
KOSH
|
|
|
CRSR
|WITTMAN
KOSH
|REGL
|
|N 43^59.06'
|W 88^33.42'
enr-leg ent APT 1
Figure 3-92
|+++++Ê+++++
045^fr|DIS
15.2nm|GS
Figure 3-93
|WITTMAN
045^fr|REGL
15.2nm|
Figure 3-94
|WITTMAN
KOSH
|REGL
|
|N 43^59.06'
|W 88^33.42'
enr-leg ent APT 1
Figure 3-95
|
|
|
|
|
Figure 3-89
|
|
|
|
|
Figure 3-91
$=KOSH
683nm
193kt
3:34
303^
NAV 1
APT 1
Rev 1
Hide quick links:
Advertisement
Table of Contents
