HP StorageWorks 7100 - Virtual Array Appendix page 9

Event Event
Number Name
(dec/hex)
122/0x7a Hardware error prevents
successful command
completion
123/0x7b Host Port Behavior Table
overflow
124/0x7c
Sequencer error injection error
125/0x7d Test mode is required for this
command
126/0x7e
Subsystem LUN configuration
changed UA
127/0x7f Mode parameters were restored
from defaults UA
128/0x80
Limit to supported number of
Principals has been reached
129/0x81 Disk Interface Error - no
logging
130/0x82
Disk Interface Error
131/0x83 Disk Interface Command
Failed
132/0x84
Host is not authorized to access
LUN
133/0x85 Cannot identify a FRU in
phatom enclosure with id 0xff
134/0x86 Journal Manager Buffer Write
Failed
135/0x87 Journal Manager Stage Write
Failed
Event Event
Number Name
(dec/hex)
256/0x100 Access Time Count Error
257/0x101 Disk Drive Placed In Failed
State
258/0x102 NVRAM Image Out Of Date
259/0x103 No Quorum For Disk Set
Access
Predictive Suspected
Maintenance Components
Implication
Y None of these are Unknown
allowed
Y None of these are Unknown
allowed
N These only occur Unknown
in internal testing
N These only occur Unknown
in internal testing
N Ignore None
N Ignore None
Y Ignore - Remove None
unwanted
associations from
Security map
N N.A. None
Y N.A. None
Y N.A. None
Y Ignore - Host None
doesn't have
permission to
access LUN
Y Ignore - Cannot None
identify FRU in
phantom
enclosure
Y N.A. Journal
Manager
Y N.A. Journal
Manager
E Predictive Suspected
v
e
nt
L Maintenance Components
o
g
g
e
d
?
Implication
Y Ignore. None
Y Single Disk Drive,
Occurrance Controller,
Back End FC
Link
Y Ignore - Operator None
activity
Y Ignore - Operator None
activity or
Description
parameters stored there will probably revert to their
default values.
Y The command failed because a required access to
hardware failed and was either not retried or was
retried unsuccessfully.
Y An attempt was made to add a new entry to the host
port behavior table but no unused entry was
available. An existing entry must be deleted to
make room for the new entry.
Y This error is used for a variety of purposes when
injecting errors in sequencer module tests.
Y The command that was received is only allowed
when the test mode flag in the personality is true.
N This error is used to report a Unit Attention for LUN
Inventory changed.
N This error is used to report a Unit Attention for the
case where mode parameters were restored from
defaults.
Y The LUN Security Utility cannot add any more
associations for new Principals because the
supported limit for Principals has been reached.
N A command to a backend device failed in an
expected manner, so that logging is not required.
N A command to a backend device failed with sense
data indicating an unexpected error.
N A command to a backend device failed due to an
error that does not include sense data from the
device.
Y LUN Security Authoriztion failed - Host attempted
to perform an operation on a LUN without having
an appropriate access permission.
N Phantom enclosure is a collection of disks with no
physical slot mapping. Ideally there should not be
any disk in phatom enclosure
Y A Journal Manager Buffer Write has failed.
Resilient map updates have not been posted to disk.
FUA write failures may result from this condition
Y A Journal Manager Stage Write has failed. Resilient
map updates have not been posted to disk. FUA
write failures may result from this condition
M Description
fg
F
ai
l?
N The frequency distribution table used to locate
recently modified blocks was found to be
inconsistent. This is indicative of a firmware
problem. This problem is self correcting.
N The firmware made a decision to automatically fail
a disk device due to its accumulated error history.
N During startup a disk stamp newer than the
NVRAM committed stamp copy was found. This
indicates the volume set attached successfully to a
different controller and this VS related NVRAM is
not valid.
N During startup a quorum of the drives belonging to
the volume set the NVRAM stamp were not present.