HP StorageWorks 7100 - Virtual Array Appendix page 27

Event Event
Number Name
(dec/hex)
563/0x233 PDM Add
564/0x234 Disk Redundant Path Found
565/0x235
Disk Redundant Path Lost
566/0x236 State Changing Start
567/0x237 State Changing End
568/0x238
Disk Driver Created
569/0x239 Disk Driver Deleted
570/0x23a Hot Plug Event
571/0x23b New Device Found
572/0x23c Old Device Lost
573/0x23d
Warning Indicator Activated
574/0x23e Warning Indicator Deactivated
575/0x23f
PDM Label Table Mismatch
576/0x240
Uploaded mode parms were
defaulted
577/0x241
Start multi disk loss scan
578/0x242
Multi disk loss detected
579/0x243 Exit multi disk loss reset
580/0x244
Policy generated relocation
error
581/0x245 Insufficent space for policy
relocation
582/0x246
Frontend Fibre Channel Hung
Port Event
583/0x247 DDM Disk Change Event
584/0x248 Repair of corrupted eeprom
done.
Predictive Suspected
Maintenance Components
Implication
Y Ignore Disk
Y Disk
Y Disk
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y NA None
Y Ignore. should controller
be other prior
failure events
Y Ignore. should controller
be other prior
failure events
Y Ignore. should controller
be other prior
failure events
Y NA None
Y NA None
Y Ignore None
Y Ignore None
Y Ignore Controller
EEPROM
Description
The actual blockSize is output in the verbose log
eventInfo.
N A PDM has been added for the specified device.
This could mean that a previously downed drive is
being re-added, or that a PDM was added for a
newly added drive.
N A redundant path to an already known drive has
been discovered.
N A redundant path to an already known drive has
been lost.
N The state changing bit has been asserted.
N The state changing bit has been deasserted.
N A PDD (proxy and real) has been instantiated for a
disk.
N A PDD (proxy and real) has been destroyed for a
disk.
N A generic hot plug event occurred. See the event
unique description for more information.
N A new device was discovered by CFMhot.
N A device CFMhot already knew about has
disappeared.
N One of the warning indicators has been actviated.
Check the extended event information for more
information.
N One of the warning indicators has been deactviated.
Check the extended event information for more
information.
N A PDM, during instantiation, came up with different
basic information. One possible cause is
downloading unsupported mech FW that doesn't
conform to the required capacity point for drive
category.
Y The midplane EEPROM mode parameters region
contains a revision that is older than the revision
expected by current firmware. As a result, some
mode parameters were set to their default values
since there was no saved value present in the
EEPROM.
N A backend scan was started to detect a multiple disk
loss condition because of a raid 5 DP write failure.
If a multiple disk loss is detected, raid 5 DP writes
will not be allowed to proceed. Another log entry
will indicate if the condition is detected. No
additional entry will be made otherwise.
N A multiple disk loss was detected. Raid 5 DP writes
will not be processed until this condition is cleared.
N This controller is exiting from the excessive disk
missing condition. Enough of the missing disks
have been restored to attempt normal operations.
Y A policy sponsored data relocation failed.
Y There is not enough space to perform a policy
sponsored relocation.
N This error code indicates that the Front End Fibre
Channel port appears to be in a HUNG state. The
port will be reset in an attempt to recover from the
event. Additional information about the event is
placed in the extended info area of the log.
N This error is being used to indicate (in the extended
info field) changes in Dump Disk Manager disk
change event processing. This code should be
removed before release.
N The eeprom region located at 0 or 48 was corrupted
and repaired with it's backup copy at 48 or 0
respectively.