HP StorageWorks 7100 - Virtual Array Appendix page 19

Event Event
Number Name
(dec/hex)
381/0x17d LCC Installed
382/0x17e LCC Removed
383/0x17f DDM failed image disks
384/0x180 Battery charger firmware
downloader status
385/0x181 Failure in TWSI Driver module
386/0x182 VSC7130 chip failed
387/0x183 Internal drive inserted
388/0x184 Internal drive removed
389/0x185 Internal drive requesting port
bypass
390/0x186 Internal drive has stopped
requesting port bypass
391/0x187
Internal drive is indicating a
fault
392/0x188 Internal drive is no longer
indicating a fault
393/0x189
No GBIC Installed
394/0x18a GBIC of type MOD DEF 4
Installed
395/0x18b GBIC of type Mod Def 4
Removed
396/0x18c
GBIC Transmit Fault
397/0x18d GBIC no longer indicating
Transmit Fault
398/0x18e GBIC Receive Signal Lost
399/0x18f GBIC no longer indicating
Receive Signal Lost
400/0x190 Non-Mod Def 4 GBIC
Installed
401/0x191 Non-Mod Def 4 GBIC
Removed
402/0x192
GBIC EEPROM has failed
403/0x193 JBOD FC Signal Detected
404/0x194 JBOD FC Signal Lost
Predictive Suspected
Maintenance Components
Implication
Y Ignore - Operator LCC, Back End
Activity FC Port,
Controller
Y Ignore unless no LCC, Back End
Operator activity FC Port,
Controller
Y Ignore unless no disk drives
Operator activity
Y battery charger
Y Controller,
battery, power
supply,
midplane
Y VSC7130
Signal Detect /
Port Bypass
Control chip
Y Disk internal to
the controller
enclosure
Y Disk internal to
the controller
enclosure
Y Disk internal to
the controller
enclosure
Y Disk internal to
the controller
enclosure
Y Disk internal to
the controller
enclosure
Y Disk internal to
the controller
enclosure
Y GBIC port
Y GBIC port
Y GBIC port
Y GBIC port
Y GBIC port
Y GBIC port
Y GBIC port
Y GBIC port
Y GBIC port
Y GBIC
Y JBOD Port
Y JBOD Port
Description
is ErrEnR2. The tenth byte is ErrDR2.
N This error code indicates the system state change
consisting of an LCC hot plug insertion. The device
number of the drive added appears in this change
record. A device number consisting of the
controller serial number followed by a 0 indicates
that the device number has not yet been assigned.
N This error code indicates the system state change
consisting of an LCC hot plug removal. The device
number of the lcc removed appears in this change
record. A device number consisting of the
controller serial number followed by a 0 indicates
that the device number has not yet been assigned.
N This error code indicates the system could find a
usable image disk to reload NVRAM from at system
start up.
N This event is used to report status related to the
battery charger firmware download process. See the
extended event info field for the actual status.
Y 2C_DRIVER_FAILURE This error indicates that an
attempt to communicate with a two-wire serial
device has failed, possibly after multiple retries.
Y The VSC7130 chip used for FC signal detect and
port-bypass control has suffered a hardware failure.
There is a VSC7130 for the host port and one for the
JBOD port. This will result in the controller being
failed. See extended information for which 7130
failed.
N An internal disk has been inserted into the
enclosure.
N An internal disk has been removed from the
enclosure.
N An internal disk is requested that its FC port be
bypassed.
N An internal disk has stopped requesting that its FC
port be bypassed.
N An internal disk is indicating that it is faulted.
N An internal disk is no longer indicating that it is
faulted.
N No GBIC is installed on this controller
N A GBIC has been inserted on this controller
N A GBIC has been removed from this controller
N The GBIC is indicating a transmit fault
N The GBIC is no longer indicating a transmit fault
N The GBIC is indicating that the no receive signal is
present
N The GBIC is no longer indicating that the no receive
signal is present
Y A non-Module Definition 4 type GBIC has been
installed. This GBIC type is not supported and will
be disabled. This GBIC will also be marked as
failed.
N A non-Module Definition 4 type GBIC has been
installed. This GBIC type is not supported but will
be used anyway.
Y Unable to communicate with the EEPROM on the
GBIC. The EEPROM must be failed.
N An FC signal is now detected on the JBOD port.
N An FC signal is no longer detected on the JBOD