HP D7171A - NetServer - LPr Service & Reference Manual

NetServer LXr Pro8 Inside
Service Reference Label
Key
Check by
visual inspection
Check with
Diagnostic Assistant
System Board
Troubleshooting
Check (see board picture).
Check that system matches one of these configurations.
All processor slots must be filled.
Total Number
of CPU Chips Board in Board in Board in Board in
in System Slot A2 Slot A1 Slot B2 Slot B1
2 CPUS Terminator Processor Terminator Terminator
4 CPUS Terminator Processor Terminator Processor
6 CPUS Processor Processor Terminator Processor
8 CPUS Processor Processor Processor Processor
Check that all processors, DIMMs, and drives are connected
and responding with the Diagnostic Assistant (select Hardware
Inventory).
Check BIOS version with Diagnostic Assistant (select "Hardware
Inventory").
Check operation with Diagnostic Assistant (select "Quick Tests"
then "Run All Tests").
6
Boot Block BIOS:
6
Flash Enable / Protect
Main BIOS:
Protect / Flash Enable
6
JP8 (Reserved)
JP9
JP10
CPU BUS A
A2
PCI BUS 0 PCI BUS 1
P1 P2 P3 P4 P5 P6 P7 P8
Not Replaceable
Video Card in P1 Connector
Reserved
EXT opening in rear panel Unused Mouse
(Reset Switch)
Keyboard
Diagnostic Assistant
Serial B
disk pouch
Serial A
Reserved Firmware
5 4 3 2 1 0
Clear CMOS Enable Boot Order
BIOS Recovery Enable
1. CD-ROM (SCSI Address 0)
*
(See Panel of this label)
2. Flexible Disk
*
3. Internal SCSI Drives
5 4 3 2 1 0 Default:
4. Optional SCSI Extender Drawer
Clear CMOS Protect
5. PCI P1
BIOS Recovery Protect
• •
(See Panel of this label)
• •
• •
12. PCI P8
5 4 3 2 1 0
Default: included in boot order. To check or change,
*
press to enter Boot Menu when prompted during
E S C
CONF Power On Self-Test.
Default: included in boot order. To check or change,
press + to run SCSI Setup Utility when
C t rl C
prompted after memory count stage of boot.
ROM Setup
CPU BUS B
Press F 2 to enter Setup when prompted during
A1 B2 B1
Power On Self-Test.
Memory Test
Full Test: Press D during memory count stage of boot.
Clear CMOS
1 Ensure jumper CONF 0 on System Board is in
"Enable" position (see Panel
2 Power up system while holding
3 Keyboard LEDs flash when done
4 Power down system
5 Reset jumper to "Protect" position
Boot Status
6 Power up system (takes up to 2 minutes)
0 1 2 3 4 5 6 7
BIOS Recovery from Boot Block
1 Ensure jumper CONF 0 on System Board is in
"Enable" position (see Panel
2 Put diskette copy of BIOS file in flexible disk drive
Printer Unused
3 Power up system while holding
(Speaker)
4 Keyboard LEDs flash when done
5 Power down system
6 Reset jumper to "Protect" position
7 Power up system (takes up to 2 minutes)
Processor
Caution:
Operating a CPU chip on an incorrect Processor Board, or
at a lower or higher speed, or at incorrect voltage may result
in unreliable operation -- or cause catastrophic or hidden
damage to the chip.
Repairs due to unauthorized jumper modification or use
of incorrect chip and board combinations are not covered
under the warranty. CPU chips supplied and warranted by
HP for HP NetServers have an HP label.
on this label)
down
F 2
Reserved
Upper Lower
on this label) Processor Processor JP1
down JP4
F 3
Unused