HP Xw4600 - Workstation - 2 GB RAM Installation Manual
HP Xw4600 - Workstation - 2 GB RAM Installation Manual

HP Xw4600 - Workstation - 2 GB RAM Installation Manual

Ieee-1394 card
Hide thumbs Also See for Xw4600 - Workstation - 2 GB RAM:

Advertisement

IEEE-1394 card installation
HP xw Workstation series
This document describes how to install an IEEE-1394 card in your workstation.

Kit contents

The following components are included in your IEEE-1394 card kit:
IEEE-1394 (A or B) card
Y-adapter power cable (available in some kits)
Warranty
Installation instructions

Before you begin

Visit
http://www.hp.com/accessories/workstations
HP workstation.
ENWW
to determine the compatibility of this product with your
© 2007 Hewlett-Packard Development Company, L.P. The HP Invent logo is a registered
trademark of Hewlett-Packard Development Company, L.P. Printed in the U.S.
HP xw Workstation series
1

Advertisement

Table of Contents
loading

Summary of Contents for HP Xw4600 - Workstation - 2 GB RAM

  • Page 1: Kit Contents

    HP workstation. © 2007 Hewlett-Packard Development Company, L.P. The HP Invent logo is a registered trademark of Hewlett-Packard Development Company, L.P. Printed in the U.S. ENWW HP xw Workstation series...
  • Page 2: Warnings And Cautions

    Warnings and cautions WARNING! Any surface or area of the equipment marked with these symbols indicates the presence of a hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce the risk of injury from a hot component, allow the surface to cool before touching. WARNING! Any surface or area of the equipment marked with these symbols indicates the presence of an electrical shock hazard.
  • Page 3 CAUTION: To prevent damage to this system, observe the following Electro Static Discharge (ESD) precautions while performing the system parts removal/replacement procedures: — Work on a static-free mat. — Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your body to the ground.
  • Page 4: Step 1-Preparing The Workstation

    Step 1—Preparing the workstation Your workstation documentation includes instructions for disassembling and preparing the workstation for installation. To prepare the workstation for component installation: Power down the workstation. Disconnect power from the workstation. Open the access cover. For product-specific information, see the Service and Technical Reference Guide for your HP workstation at http://www.hp.com/support/workstation_manuals.
  • Page 5 Step 3—Installing the IEEE-1394 card CAUTION: To prevent damage to your workstation, observe the following Electro Static Discharge (ESD) precautions while performing the system parts removal/replacement procedures: - Work on a static-free mat. - Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your body to the ground.
  • Page 6 Step 4—Configuring the cabling HP xw4000/xw6000 series workstations Connect a mini-plug power connector from the workstation power supply to the power connector on the IEEE-1394 card (1). Connect the front IEEE-1394 I/O cable to the I/O connector on the IEEE-1394 card (2). Figure 3 Connecting the IEEE-1394 cables (Optional) Remove the plastic plug or adhesive label from the front 1394 port.
  • Page 7 The following table lists information to help you assemble and configure your workstation. Table 1 Configuration information xw4550 xw4000/xw6000 xw8000/xw9000 1394A ● Requires Y-adapter cable ● Power direct from power ● Power not required (function on system board) supply ● ●...

This manual is also suitable for:

Xw seriesXw4000 seriesXw6000 seriesXw4550Xw8000Xw9000

Table of Contents