Solving Option Problems - Lexmark 940e - X Color Laser Troubleshooting Manual

I
S THE DOCUMENT LOADED PROPERLY
Load the original document faceup, short-edge first into the
ADF or facedown on the scanner glass in the upper left corner.
Note: Do not load postcards, photos, small items,
transparencies, photo paper, or thin media (such as magazine
clippings) into the ADF. Place these items on the scanner glass.
M
AKE SURE THE SHORTCUT NUMBER IS SET UP
PROPERLY
• Check to make sure the shortcut number has been
programmed for the number that you want to dial.
•
As an alternative, dial the telephone number manually.
Received fax has poor print quality
These are possible solutions. Try one or more of the following:
C - ?
AN THE DOCUMENT BE RE SENT
Ask the person who sent you the fax to:
• Check that the quality of the original document is
satisfactory.
• Resend the fax. There may have been a problem with the
quality of the telephone line connection.
•
Increase the fax scan resolution, if possible.
I ?
S THE TONER LOW
When 88 <color> toner low appears or when you
experience faded print, replace the cartridge(s).
M
AKE SURE THE FAX TRANSMISSION SPEED IS NOT SET
TOO HIGH
Decrease the incoming fax transmission speed:
1
Open a Web browser.
2
In the address bar, type the IP address of the printer, and
then press Enter.
3
Click Configuration.
4
Click Fax Settings.
5
Click Analog Fax Setup.
? 6
In the Max Speed box, click on one of the following:
7
Click Submit.
Blocking junk faxes
1
Open a Web browser.
2
In the address bar, type the IP address of the printer and, then
press Enter.
3
Click Configuration.
4
Click Fax Settings.
5
Click Analog Fax Setup.
6
Click the No Name Fax option.
This option blocks all incoming faxes that have a private caller
ID or no fax station name.
7
In the Banned Fax List field, enter the phone numbers or fax
station names of specific fax callers you want to block.

Solving option problems

Option does not operate correctly or
quits after it is installed
These are possible solutions. Try one or more of the following:
R
ESET THE PRINTER
Turn the printer off, wait for about 10 seconds, and then turn
the printer on.
C
HECK TO SEE IF THE OPTION IS CONNECTED TO THE
PRINTER
1
Turn the printer off.
2
Unplug the printer.
3
Check the connection between the option and the printer.
2400
4800
9600
14400
33600
6
M
AKE SURE THE OPTION IS INSTALLED
Print a menu settings page and check to see if the option is
listed in the Installed Options list. If the option is not listed,
reinstall it.
M
AKE SURE THE OPTION IS SELECTED
From the program you are using, select the option. Mac OS 9
users should make sure the printer is set up in the Chooser.
Drawers
M
AKE SURE THE PAPER IS LOADED CORRECTLY
1
Open the paper tray.
2
Check for paper jams or misfeeds.
3
Make sure paper guides are aligned against the edges of
the paper.
4
Make sure the paper tray closes properly.
5
Close the door.
R
ESET THE PRINTER
Turn the printer off. Wait 10 seconds. Turn the printer back on.
Finisher
If the finisher does not operate correctly, these are possible
solutions. Try one or more of the following:
M
AKE SURE THE CONNECTION BETWEEN THE FINISHER
AND THE PRINTER IS SECURE
If the finisher is listed on the menu settings page, but paper
jams when it exits the printer and enters the finisher, it may not
be properly installed. Reinstall the finisher. For more
information, see the hardware setup documentation that
shipped with the finisher.