1. Manuals
  2. Brands
  3. IBM Manuals
  4. Server
  5. 8485E2U
  6. Installation manual

IBM 8485E2U Installation Manual

User manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

xSeries 206m
Types 8485 and 8490

Installation Guide

Welcome. . .
Thank you for buying an
IBM xSeries server.
This server
Installation Guide
contains information for setting
up and configuring your server.
For detailed information
about your server, view the
User's Guide
on the
Documentation CD.
You can also find the most
current information about your
server on the IBM Web site at:
http://www.ibm.com/support/
Install options:
Drives
Adapters
Memory
Install the server in
the rack, if required
Cable the server
and options
Start the server
No
Did the server
start correctly?
Yes
Use ServerGuide
to set up and
configure hardware
No
Did configuration
complete?
Yes
Use
No
ServerGuide to
install operating
system?
Yes
Use ServerGuide to
install applications,
such as IBM systems
management software
and IBM ServeRAID
programs
System is ready to use.
Go to the Server Support
flow chart to register
your server.
Go to the Server Support
flow chart inside this cover page.
Go to the Web for Instructions,
http://www.ibm.com/support/

Advertisement

Table of Contents
loading

Related Manuals for IBM 8485E2U

Summary of Contents for IBM 8485E2U

  • Page 1: Installation Guide

    Documentation CD. You can also find the most Did configuration complete? current information about your server on the IBM Web site at: http://www.ibm.com/support/ ServerGuide to Go to the Web for Instructions, install operating http://www.ibm.com/support/ system? Use ServerGuide to...

  • Page 2: Server Support

    Check all cables for loose connections and verify that all optional devices you installed are on the ServerProven list at http://www.ibm.com/servers/eserver/ serverproven/compat/us/. View information about IBM Support Line at http://www.ibm.com/services/sl/products/ or view support telephone numbers at Is the problem http://www.ibm.com/planetwide/.
  • Page 3 xSeries 206m Types 8485 and 8490 Installation Guide...
  • Page 4 Note: Before using this information and the product it supports, read the general information in Appendix B, “Notices,” on page 79, and the Warranty and Support Information document on the IBM xSeries Documentation CD. Third Edition (October 2006) © Copyright International Business Machines Corporation 2006. All rights reserved.

  • Page 5: Table Of Contents

    Chapter 1. Introduction ..... . 1 The IBM xSeries Documentation CD ....3 Hardware and software requirements .
  • Page 6 Chapter 5. Solving problems ....49 Diagnostic tools overview ..... 49 POST beep codes .

  • Page 7: Safety

    Vor der Installation dieses Produkts die Sicherheitshinweise lesen. Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza. Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet. Antes de instalar este produto, leia as Informações sobre Segurança. © Copyright IBM Corp. 2006...
  • Page 8 IBM Safety Information book. For example, if a caution statement begins with a number 1, translations for that caution statement appear in the IBM Safety Information book under statement 1. Be sure to read all caution and danger statements in this documentation before performing the instructions.
  • Page 9 Statement 1: DANGER Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: v Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. v Connect all power cords to a properly wired and grounded electrical outlet.
  • Page 10 Statement 2: CAUTION: When replacing the lithium battery, use only IBM Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer.
  • Page 11 Statement 3: CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: v Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device.
  • Page 12 Statement 4: ≥ 18 kg (39.7 lb) ≥ 32 kg (70.5 lb) ≥ 55 kg (121.2 lb) CAUTION: Use safe practices when lifting. Statement 5: CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device.
  • Page 13 Statement 8: CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components.
  • Page 14 Statement 15: CAUTION: Make sure that the rack is secured properly to avoid tipping when the server unit is extended. WARNING: Handling the cord on this product or cords associated with accessories sold with this product, will expose you to lead, a chemical known to the State of California to cause cancer, and birth defects or other reproductive harm.

  • Page 15: Chapter 1. Introduction

    2. Under Search technical support, type 8485 or 8490 (depending on the machine type for your server model), and click Search. The server comes with an IBM ServerGuide Setup and Installation CD to help you configure the hardware, install device drivers, and install the operating system.
  • Page 16 These illustrations might differ slightly from your hardware. Several models are available; for additional information, see the User’s Guide on the IBM xSeries Documentation CD. The following illustration shows a hot-swap model. Model number and serial number Important: The server keys cannot be duplicated by a locksmith.

  • Page 17: The Ibm Xseries Documentation Cd

    The IBM xSeries Documentation CD The IBM xSeries Documentation CD contains documentation for the server in Portable Document Format (PDF) and includes the IBM Documentation Browser to help you find information quickly. Hardware and software requirements The IBM xSeries Documentation CD requires the following minimum hardware and software: ®...

  • Page 18: Notices And Statements In This Document

    Notices and statements in this document The caution and danger statements that appear in this document are also in the multilingual Safety Information document, which is on the IBM xSeries Documentation CD. Each statement is numbered for reference to the corresponding statement in the Safety Information document.

  • Page 19: Features And Specifications

    Features and specifications The following information is a summary of the features and specifications of the server. Depending on the server model, some features might not be available, or some specifications might not apply. Table 1. Features and specifications Microprocessor: Fans: Environment: ®...

  • Page 20: Major Components Of The Xseries 206M Types 8485 And 8490

    Major components of the xSeries 206m Types 8485 and 8490 Blue on a component indicates touch points, where you can grip the component to remove it from or install it in the server, open or close a latch, and so on. Orange on a component or an orange label on or near a component indicates that the component can be hot-swapped, which means that if the server and operating system support hot-swap capability, you can remove or install the component while...

  • Page 21: Chapter 2. Installing Options

    Chapter 2. Installing options This chapter provides basic instructions for installing hardware options in the server. These instructions are intended for users who are experienced with setting up IBM server hardware. If you need more detailed instructions, see the User’s Guide on the IBM xSeries Documentation CD.

  • Page 22: System Reliability Guidelines

    System reliability guidelines To help ensure proper system cooling and system reliability, make sure that the following requirements are met: v Each of the drive bays has a drive or a filler panel and electromagnetic compatibility (EMC) shield installed in it. v There is adequate space around the server to allow the server cooling system to work properly.

  • Page 23: Handling Static-Sensitive Devices

    Handling static-sensitive devices Attention: Static electricity can damage the server and other electronic devices. To avoid damage, keep static-sensitive devices in their static-protective packages until you are ready to install them. To reduce the possibility of electrostatic discharge, observe the following precautions: v Limit your movement.

  • Page 24: Removing The Side Cover

    Removing the side cover To remove the server side cover, complete the following steps: 1. Review the safety information that begins on page v and the “Installation guidelines” on page 7. 2. Turn off the server and all attached devices (see “Turning off the server” on page 36);...

  • Page 25: Removing The Two-Piece Bezel

    Removing the two-piece bezel When working with some devices, such as drives in bays 1 through 7, you must first remove the two-piece bezel to access the devices. Notes: v Before you remove the upper bezel, you must: – Unlock and remove the side cover –...
  • Page 26 5. Carefully pull the two bezel clips on the left side of the upper bezel away from the chassis; then, rotate the upper bezel to the right side of the server to disengage the two right-side tabs from the chassis. Set the upper bezel aside. For instructions for reinstalling the two-piece bezel, see “Reinstalling the two-piece bezel”...

  • Page 27: Installing A Memory Module

    Configuration/Setup Utility program and select System Summary from the menu. For additional information, see the User’s Guide on the IBM xSeries Documentation CD. v For two-way memory interleaving, DIMMs must be installed in matched pairs. If one DIMM is installed in the DIMM 1 connector, when you install an additional DIMM, it must be installed in the DIMM 3 connector, and it must be the same size, speed, type, and technology as the DIMM in the DIMM 1 connector.
  • Page 28 The following illustration shows the dual inline memory module (DIMM) connectors and corresponding LEDs on the system board. DIMM 1 DIMM 2 DIMM 3 DIMM 4 DIMM 4 error LED DIMM 3 error LED DIMM 2 error LED DIMM 1 error LED Attention: Static electricity that is released to internal server components when the server is powered-on might cause the server to stop, which could result in the...
  • Page 29 4. Locate the DIMM connectors on the system board. Determine the connectors into which you will install the DIMMs. Install the DIMMs in the sequence shown in the following table. Number of DIMMs Connector sequence One DIMM Two DIMMs (interleaved configuration) 1, 3 Three DIMMs Not supported...

  • Page 30: Installing A Drive

    Installing a drive Depending on the server model, one or more of the following drives might be installed in the server: v Diskette drive (optional) v Hard disk drive v CD-ROM, CD-RW, or DVD/CD-RW combo drive Some hot-swap Serial Attached SCSI (SAS) models might come with an integrated drive electronics (IDE) CD-ROM drive in bay 1 and four hot-swap hard disk drive bays.

  • Page 31: Installing A Drive In Bay 2 Or 3

    EMC shield and filler panel from the bay or the PCI, PCI Express, or PCI-X adapter slot cover in the event that you later remove the option. v For a complete list of supported options for the server, see http://www.ibm.com/ servers/eserver/serverproven/compat/us/.
  • Page 32 5. Use a screwdriver to pry the filler panel and EMC shield away from the server. Note: If you are installing a drive that contains a laser, observe the following safety precaution. Statement 3: CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: v Do not remove the covers.

  • Page 33: Installing A Hot-Swap Hard Disk Drive In Bay 4, 5, 6, Or 7

    to the left to remove it from the drive cage; then, snap the drive retainer clip into the screw holes on the side of the drive (the blue side of the drive retainer clip should be facing outward). 9. If you are installing a 5.25-in. drive in bay 2, push the drive into the bay. If you are installing a 3.5-in.
  • Page 34 Filler panel Drive-tray assembly Drive tray handle (in open position) To install a hot-swap hard disk drive, complete the following steps: 1. Read the safety information that begins on page v and “Installation guidelines” on page 7. 2. Unlock the side cover. 3.

  • Page 35: Ids For Hot-Swap Hard Disk Drives

    IBM ServeRAID Support CD for additional information about RAID operation and complete instructions for using ServeRAID Manager. 6. If you are installing additional hot-swap hard disk drives, do so now. If you have other options to install or remove, do so now; otherwise go to “Completing the installation”...
  • Page 36 To install a simple-swap hard disk drive, complete the following steps: 1. Read the safety information that begins on page v and “Installation guidelines” on page 7. 2. Turn off the server and peripheral devices and disconnect all external cables and power cords.

  • Page 37: Installing A Non-Hot-Swap Sata Hard Disk Drive In Bay 4, 5, 6, Or 7

    Installing a non-hot-swap SATA hard disk drive in bay 4, 5, 6, or 7 Some server models come with non-hot-swap SATA hard disk drives. Before you install a non-hot-swap SATA hard disk drive, read the following information: v Read the documentation that comes with the drive for cabling instructions. v Route the cable before you install non-hot-swap drives.

  • Page 38: Power And Signal Cables For Internal Drives

    The server uses cables to connect parallel IDE, simple-swap SATA, and SAS devices to the power supply and to the system board. (For the location of the system-board connectors, see the User’s Guide on the IBM xSeries Documentation CD.) Review the following information before connecting power and signal cables to...

  • Page 39: Installing An Adapter

    64-bit adapters in a hot-swap model, you must install them only in slots 5 and 6. v An optional IBM Remote Supervisor Adapter II can be installed only in the following slots: PCI slots 3 and 4. Use the ribbon cable that comes with this adapter to connect it to the Remote Supervisor Adapter II cable connector on the system board.
  • Page 40 Express x8 slot 1, PCI-X slot 5 (optional), PCI-X slot 6 (optional), PCI Express x1 slot 2, PCI slot 3, and PCI slot 4. v For a list of supported options for the server, see http://www.ibm.com/servers/ eserver/serverproven/compat/us/. For the locations of the expansion slots on the system board and the optional PCI-X expansion card, see the User’s Guide on the IBM xSeries Documentation CD.
  • Page 41 1. Read the safety information that begins on page v and “Installation guidelines” on page 7. 2. Turn off the server and peripheral devices and disconnect all external cables and power cords; then, remove the side cover. See “Removing the side cover” on page 10.

  • Page 42: Completing The Installation

    13. Reinstall the rear adapter-retention bracket; then, rotate the bracket to the closed (locked) position. Note: If any adapters in the server are large or have heavy cables attached to them, you can remove the rear adapter-retention bracket and secure all of the adapters with expansion-slot screws.
  • Page 43 2. Install the lower bezel on the front of the server chassis. a. Insert the two bottom tabs on the lower bezel into the matching holes in the front of the chassis. b. Tilt the top of the lower bezel into position on the chassis until the lower bezel locks securely into place.

  • Page 44: Reinstalling The Side Cover

    Reinstalling the side cover If you removed the bezel, reinstall it before you reinstall the side cover. See “Reinstalling the two-piece bezel” on page 28. Note: The rear adapter-retention bracket rests against the server side cover. You might find it easier to lay the server on its side to reinstall the side cover. Cover-release latch Key lock...

  • Page 45: Connecting The Cables

    Connecting the cables Attention: To prevent damage to equipment, connect the power cords last. If the server cables and connector panel have color-coded connections, match the color of the cable end with the color of the connector. For example, match a blue cable end with a blue panel connector, a red cable end with a red connector, and so on.

  • Page 46: Updating The Server Configuration

    Updating the server configuration When you start the server for the first time after you add or remove an internal option or an external device, you might receive a message that the configuration has changed. The Configuration/Setup Utility program starts automatically so that you can save the new configuration settings.

  • Page 47: Chapter 3. Server Controls, Leds, And Power

    An LED on the system board might also be lit to help isolate the error. See Chapter 5, “Solving problems,” on page 49 for additional information. Detailed troubleshooting information is in the Problem Determination and Service Guide on the IBM xSeries Documentation CD. © Copyright IBM Corp. 2006...
  • Page 48 USB connectors Connect USB devices to these connectors. CD-eject or DVD-eject button Press this button to release a CD from the CD drive or a DVD from the DVD drive. CD or DVD drive activity LED When this LED is lit, it indicates that the CD drive or DVD drive is in use. (Optional) Diskette-eject button Press this button to release a diskette from the diskette drive.

  • Page 49: Rear View

    Rear view The following illustration shows the connectors on the rear of the server. Power cord Power supply error LED AC power LED Mouse Keyboard Serial 1 Parallel Video USB (2) Ethernet Serial 2 Power-cord connector Connect the power cord to this connector. Mouse connector Connect a mouse or other PS/2 device to this connector.

  • Page 50: Server Power Features

    Ethernet transmit/receive activity LED This LED is on the Ethernet connector on the rear of the server. When this LED is lit, it indicates that there is activity between the server and the network. Ethernet link status LED This LED is on the Ethernet connector on the rear of the server. When this LED is lit, it indicates that there is an active connection on the Ethernet port.
  • Page 51 Statement 5: CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.
  • Page 52 xSeries 206m Types 8485 and 8490: Installation Guide...

  • Page 53: Chapter 4. Configuring The Server

    MIGR-4ZKPPT.html. Important:: If your server comes preloaded with an operating system and software, you do not need to use the IBM ServerGuide Setup and Installation CD to install the operating system. This will overwrite the existing preload.

  • Page 54: Using The Configuration/Setup Utility Program

    Configuration/Setup Utility menu. 3. Follow the instructions on the screen. See the User’s Guide on the IBM xSeries Documentation CD for more detailed information about the Configuration/Setup Utility program. Using the SAS/SATA Configuration Utility program (hot-swap...

  • Page 55: Using The Adaptec Hostraid Configuration Programs

    UnixWare 7.14 operating systems. Use the Adaptec RAID Configuration Utility programs and SAS/SATA Configuration Utility (also referred to as IBM ServeRAID-7e) to add RAID level-0 and level-1 functionality to the integrated Serial ATA controller (simple-swap SATA models) and the SAS/SATA controller (hot-swap models). Be sure to use these programs as described in this document.
  • Page 56 IBM ServeRAID-7e (Adaptec HostRAID) Support CD. If this CD did not come with the server, you can download it from http://www.ibm.com/ support/. The integrated Serial ATA RAID feature (SATA HostRAID) comes disabled by default. You must enable it and install the device drivers before you can use it. The SATA RAID feature configuration utilities, device drivers, and information are available on the IBM ServeRAID-7e (Adaptec HostRAID) Support CD.
  • Page 57 Viewing the configuration: To view information about the SATA controller, complete the following steps: 1. Start the Array Configuration Utility. 2. From the Array Configuration Utility window, select Manage Arrays. 3. Select an array and press Enter. 4. Press Esc to exit from the program. Chapter 4.

  • Page 58: Using The Sas/Sata Utility Program (For Sas/Sata Hostraid)

    The integrated SAS/SATA RAID feature comes disabled by default. You must enable it and install the device drivers before you can use it. The RAID configuration utilities, device drivers, and information are available on the IBM ServeRAID-7e (Adaptec HostRAID) Support CD. If this CD did not come with the server, you can download it from http://www.ibm.com/support/.

  • Page 59: Using Serveraid Manager

    Important: RAID options and HostRAID are not supported on the SCO 6.0 and UnixWare 7.14 operating systems. Use ServeRAID Manager, which is on the IBM ServeRAID Support CD, to perform the following tasks: v Configure a redundant array of independent disks (RAID) array...

  • Page 60: Viewing The Configuration

    and creating a RAID level-1 logical drive. If you select custom configuration, you can select the two physical drives that you want to group into an array and create a hot-spare drive. Using express configuration To use express configuration, complete the following steps: 1.

  • Page 61: Using The Boot Menu Program

    To find updated information about configuring the controller, complete the following steps. Note: Changes are made periodically to the IBM Web site. The actual procedure might vary slightly from what is described in this document. 1. Go to http://www.ibm.com/support/.
  • Page 62 xSeries 206m Types 8485 and 8490: Installation Guide...

  • Page 63: Chapter 5. Solving Problems

    If you cannot locate and correct the problem using the information in this chapter, see Appendix A, “Getting help and technical assistance,” on page 77, the Problem Determination and Service Guide on the IBM xSeries Documentation CD, and the “Server Support” flowchart in the front of this document.

  • Page 64: Post Error Codes

    POST error codes The following table provides an abbreviated list of the error codes that might appear during POST. See the Problem Determination and Service Guide on the IBM xSeries Documentation CD for more information about the POST error codes. To check for updated technical information, go to http://www.ibm.com/support/, and...
  • Page 65 Table 2. Abbreviated list of POST error codes (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Problem Determination and Service Guide to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
  • Page 66 Adapter II firmware (see the Note: In this case, the service Problem Determination and processor is the optional Remote Service Guide on the IBM Supervisor Adapter II. xSeries Documentation CD). 2. Replace the Remote Supervisor Adapter II.
  • Page 67 Table 2. Abbreviated list of POST error codes (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Problem Determination and Service Guide to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
  • Page 68 Remote Supervisor Supervisor Adapter II Adapter II or the mini-BMC. firmware (see the Problem Determination and Service Guide on the IBM xSeries Documentation CD). b. Replace the Remote Supervisor Adapter II. 2. Update the mini-BMC firmware (see the Problem...
  • Page 69 Note: x is the drive that has the diagnostic tests on drive x (see error. “Running the diagnostic programs” in the Problem Determination and Service Guide on the IBM xSeries Documentation CD). 2. Reseat the following components, depending on the server model: v Hot-swap models: a.
  • Page 70 (boot) device is positioned early in the scanning order. (For information about the scanning order, see the User’s Guide on the IBM xSeries Documentation CD). 3. Make sure that the settings for the adapter and all other adapters in the Configuration/Setup Utility program are correct.
  • Page 71 Table 2. Abbreviated list of POST error codes (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Problem Determination and Service Guide to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
  • Page 72 Table 2. Abbreviated list of POST error codes (continued) v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Problem Determination and Service Guide to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
  • Page 73 2. Run the hard disk drive diagnostic tests (see “Running the diagnostic programs” in the Problem Determination and Service Guide on the IBM xSeries Documentation CD). 3. Reseat the following components, depending on the server model: v Hot-swap models: a.
  • Page 74 System board 01298001 No update data for microprocessor 1. Update the BIOS code again (see the Problem Determination and Service Guide on the IBM xSeries Documentation CD). 2. (Trained service technician only) Reseat the microprocessor. 3. (Trained service technician only) Replace the microprocessor.
  • Page 75 Action 01298101 Bad update data for processor 1. 1. Update the BIOS code again (see the Problem Determination and Service Guide on the IBM xSeries Documentation CD). 2. (Trained service technician only) Reseat the microprocessor. 3. (Trained service technician only) Replace the microprocessor.
  • Page 76 Documentation CD). 2. Run the hard disk drive diagnostic tests (see “Running the diagnostic programs” in the Problem Determination and Service Guide on the IBM xSeries Documentation CD). 3. Reseat the following components, depending on the server model: v Hot-swap models: a.

  • Page 77: Serverguide Problems

    Troubleshooting tables Use the following tables to find solutions to problems that have identifiable symptoms. See the Problem Determination and Service Guide on the IBM xSeries Documentation CD for more detailed troubleshooting information. If you cannot find the problem in these tables, run the diagnostic programs (see “Running the diagnostic programs”...

  • Page 78: Cd Or Dvd Drive Problems

    1. Check the system-board LEDs or the LEDs on the front panel (see “System-board LEDs” on page 76). 2. Remove the software or device that you added. 3. Run the diagnostic tests to determine whether the server is running correctly. 4.

  • Page 79: Diskette Drive Problems

    76 mm (3 in.). If the problem remains, replace the internal diskette drive (see the Problem Determination and Service Guide on the IBM xSeries Documentation CD). General problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.

  • Page 80: Intermittent Problems

    A hard disk drive passes the Run the diagnostic SCSI Fixed Disk Test (see “Running the diagnostic programs” in diagnostic Fixed Disk Test but the Problem Determination and Service Guide on the IBM xSeries Documentation the problem remains. CD). Note: This test is not available on servers that have RAID arrays or servers that have SATA hard disk drives.

  • Page 81: Keyboard, Mouse, Or Pointing-Device Problems

    Keyboard, mouse, or pointing-device problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Problem Determination and Service Guide to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).

  • Page 82: Memory Problems

    4. Make sure that there is no memory mismatch when the server is over the minimum memory configuration (one 512 MB DIMM) and that you have installed the correct number of DIMMs (see the User’s Guide on the IBM xSeries Documentation CD for information about installing optional memory modules).

  • Page 83: Microprocessor Problems

    (Trained service technician only) System board Monitor problems Some IBM monitors have their own self-tests. If you suspect a problem with your monitor, see the information that comes with the monitor for instructions for testing and adjusting the monitor. If you cannot diagnose the problem, call for service.
  • Page 84 2. Run video diagnostics (see “Running the diagnostic programs” in the Problem Determination and Service Guide on the IBM xSeries Documentation CD). v If the server passes the video diagnostics, the video is good; see “Solving undetermined problems” in the Problem Determination and Service Guide.
  • Page 85 To prevent diskette drive read/write errors, make sure that the distance between the monitor and any external diskette drive is at least 76 mm (3 in.). b. Non-IBM monitor cables might cause unpredictable problems. 2. Reseat the following components: a. Monitor cable b.

  • Page 86: Optional-Device Problems

    An IBM optional device that was 1. Make sure that: just installed does not work. v The device is designed for the server (see http://www.ibm.com/servers/ eserver/serverproven/compat/us/). v You followed the installation instructions that came with the device and the device is installed correctly.

  • Page 87: Power Problems

    If the server does not start, bypass the front-panel assembly power-control button by using the force power-on jumper (see the Problem Determination and Service Guide on the IBM xSeries Documentation CD). If the server starts, reseat the front-panel assembly cable and repeat steps 1a through 1c.

  • Page 88: Serial Port Problems

    Serial port problems For more information about the serial port, see the User’s Guide on the IBM xSeries Documentation CD. v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.

  • Page 89: Software Problems

    A USB device does not work. 1. Run USB diagnostics (see “Running the diagnostic programs” in the Problem Determination and Service Guide on the IBM xSeries Documentation CD). 2. Make sure that: v The correct USB device driver is installed.

  • Page 90: System-Board Leds

    LED will be lit again. For additional information, see the Problem Determination and Service Guide on the IBM xSeries Documentation CD. xSeries 206m Types 8485 and 8490: Installation Guide...

  • Page 91: Appendix A. Getting Help And Technical Assistance

    If you need help, service, or technical assistance or just want more information about IBM products, you will find a wide variety of sources available from IBM to assist you. This appendix contains information about where to go for additional...

  • Page 92: Getting Help And Information From The World Wide Web

    Getting help and information from the World Wide Web On the World Wide Web, the IBM Web site has up-to-date information about IBM Eserver and IntelliStation systems, optional devices, services, and support. The ® address for IBM xSeries and BladeCenter information is http://www.ibm.com/...

  • Page 93: Appendix B. Notices

    Web sites. The materials at those Web sites are not part of the materials for this IBM product, and use of those Web sites is at your own risk. IBM may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you.

  • Page 94: Trademarks

    Chipkill ThinkPad EtherJet Tivoli e-business logo Tivoli Enterprise Eserver Update Connector FlashCopy Wake on LAN XA-32 IBM (logo) XA-64 IntelliStation X-Architecture NetBAY XceL4 Netfinity XpandOnDemand NetView xSeries OS/2 WARP Intel, MMX, and Pentium are trademarks of Intel Corporation in the United States, other countries, or both.

  • Page 95: Product Recycling And Disposal

    IBM makes no representations or warranties with respect to non-IBM products. Support (if any) for the non-IBM products is provided by the third party, not IBM. Some software may differ from its retail version (if available), and may not include user manuals or all program functionality.

  • Page 96: Battery Return Program

    United States, go to http://www.ibm.com/ibm/environment/ products/batteryrecycle.shtml or contact your local waste disposal facility. In the United States, IBM has established a return process for reuse, recycling, or proper disposal of used IBM sealed lead acid, nickel cadmium, nickel metal hydride, and battery packs from IBM equipment.

  • Page 97: Electronic Emission Notices (Class A)

    Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. IBM is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment.

  • Page 98: Taiwanese Class A Warning Statement

    This product has been tested and found to comply with the limits for Class A Information Technology Equipment according to CISPR 22/European Standard EN 55022.

  • Page 99: Electronic Emission Notices (Class B)

    Consult an IBM authorized dealer or service representative for help. Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Proper cables and connectors are available from IBM authorized dealers. IBM is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment.

  • Page 100: European Union Emc Directive Conformance Statement

    Japanese Voluntary Control Council for Interference (VCCI) statement Power cords For your safety, IBM provides a power cord with a grounded attachment plug to use with this IBM product. To avoid electrical shock, always use the power cord and plug with a properly grounded outlet.
  • Page 101 IBM power cords for a specific country or region are usually available only in that country or region. IBM power cord part number Used in these countries and regions 02K0546 China 13F9940 Australia, Fiji, Kiribati, Nauru, New Zealand, Papua New Guinea...
  • Page 102 IBM power cord part number Used in these countries and regions 6952300 Antigua and Barbuda, Aruba, Bahamas, Barbados, Belize, Bermuda, Bolivia, Caicos Islands, Canada, Cayman Islands, Colombia, Costa Rica, Cuba, Dominican Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Jamaica, Mexico,...

  • Page 103: Index

    16 Configuration/Setup Utility 40 cables 24 custom 46 hot-swap enabling SATA options on Configuration/Setup Utility installation 19 menu 40 support 16 Ethernet controller 47 installing 16 express 46 non-hot-swap 23 fine-tuning 46 removable-media 17 © Copyright IBM Corp. 2006...
  • Page 104 19 keyboard 67 specifications 5 keyboard, USB 75 memory 68 microprocessor 69 mouse 67 IBM Configuration/Setup Utility program 40 mouse, USB 75 IDs for SAS hot-swap drives 21 optional devices 72 important notices 4 pointing device 67 indicators 33...
  • Page 105 integrated Serial ATA controller, configuring 42 intermittent problems 66 online publications 1 internal optional device drive bays 16 installation guidelines 7 drives, installing 16 problems 72 static-sensitive 9 options adapters 25, 26 keyboard connector 35 connectors 35 keyboard problems 67, 75 drives 16 keys 2 installing 7...
  • Page 106 Serial Attached SCSI (SAS) (continued) backplane redundant array of independent disks (RAID) activity LEDs for hot-swap drives 34 Adaptec HostRAID 41 description 19 adapter 21, 25 IDs for hot-swap drives 21 enabling SATA options on Configuration/Setup Utility status LEDs for hot-swap drives 34 menu 40 hot-swap drives 19, 20 non-support 40, 45...
  • Page 107 SAS/SATA controller 45 Serial ATA controller 43 ServeRAID Manager 46 Web site compatible options 2, 7, 13 IBM eServer and xSeries products 1, 78 IBM support 1, 77 ordering publications 77 ServerProven list 2, 7, 13 software service and support 78...
  • Page 108 xSeries 206m Types 8485 and 8490: Installation Guide...
  • Page 110 Part Number: 40K2367 Printed in USA (1P) P/N: 40K2367...

This manual is also suitable for:

Xseries 206m84858490

Table of Contents