Sony XAV-701BT Installation/Connections page 2
Av center
Hide thumbs
Also See for XAV-701BT:
- User manual ,
- Service manual (124 pages) ,
- Installation/connections (2 pages)
Advertisement
Foot brake type
Parking brake switch cord
XAV-701BT only
A
1
2
b
a
a
b
Clips (not supplied)
Face the hook inwards.
Hand brake type
Parking brake switch cord
B
1
2
a
b
Clip (not supplied)
A
1
Larger than 182 mm (7
a
c
b
B
Precautions
Choose the installation location carefully so that the unit
will not interfere with normal driving operations.
Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperature, such as in
direct sunlight or near heater ducts.
Use only the supplied mounting hardware for a safe and
secure installation.
To open/close the front panel smoothly, insert/eject a
disc easily, and especially to drive safely, a certain
distance between the front panel and the shift lever is
necessary. The necessary distance differs, depending on
the shift lever position of your car. Before installing the
unit, choose the installation location carefully so that
you can drive safely.
87 mm (3
/
in)
1
2
Shift lever
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Connecting the parking brake
lead
Be sure to connect the parking brake lead (light green) of
the power supply connection cable to the parking brake
switch cord. The mounting position of the parking brake
switch cord depends on your car. Consult your car dealer
or your nearest Sony dealer for further details.
Installing the microphone
(XAV-701BT only)
To capture your voice during handsfree calling, you need
to install the microphone .
Cautions
Keep the microphone away from extremely high
temperatures and humidity.
It is extremely dangerous if the cord becomes wound
around the steering column or gearstick. Be sure to keep
it and other parts from obstructing your driving.
If airbags or any other shock-absorbing equipment is in
your car, contact the store where you purchased this
unit, or the car dealer, before installation.
2
3
/
in)
1
4
Larger than 111 mm (4
/
in)
3
8
Claws
Size:
5 × max. 8 mm
(
/
× max.
/
in)
7
5
32
16
To the dashboard/center console
Bracket
Parts supplied with your car
Bracket
-A Installing on the sun visor
Mounting the unit
1
Install the microphone
a
on the clip
b
.
2
Install the clip
b
on the sun visor.
3
Install clips (not supplied) and adjust the length
-A Mounting the unit with the supplied
and position of the cord so that it does not
bracket
obstruct your driving.
1
Position the supplied bracket inside the
dashboard.
-B Installing on the dashboard
2
Bend the claws outward for a tight fit.
1
Install the microphone
a
on the clip
, then
3
b
Mount the unit onto the supplied bracket .
place the cord along the groove of the clip
b
.
2
Attach the clip
to the dashboard with the
b
-B Mounting the unit in a Japanese car
double-sided tape
c
.
3
Install a clip (not supplied) and adjust the length
You may be able to install this unit in some makes of
and position of the cord so that it does not
Japanese cars without the supplied bracket. If you cannot,
obstruct your driving.
consult your Sony dealer.
Notes
When mounting this unit to the preinstalled brackets of
Before attaching the double-sided tape
c
, clean the surface of the
your car, use the supplied screws in the appropriate
dashboard with a dry cloth.
Adjust the microphone angle to the proper position.
screw holes, based on your car: T for TOYOTA, M for
The microphone
a
can be installed without using the clip
.
b
MITSUBISHI and N for NISSAN.
In this case, directly attach the microphone to the dashboard with the
double-sided tape
c
. Keep the unused clip
b
for future use.
Removing the bracket
Before installing the unit, remove the bracket
from the unit.
1
Insert both release keys together between the
unit and the bracket until they click.
2
Pull down the bracket , then pull up the unit to
separate them.
Notes
Adjusting the frames
To avoid a malfunction, install only with the supplied screws .
Do not apply excessive force to the buttons of the unit.
Do not press on the LCD.
You can adjust the projecting part of the unit when the
Before mounting, make sure there is nothing on the top of the unit.
unit is mounted.
Projecting part
Warning if your car's ignition
has no ACC position
Shift lever
Be sure to set the Auto Off function. For details, refer to
the supplied "Operating Instructions. "
The unit will shut off completely and automatically in the
set time when no source is selected, which prevents
battery drainage.
If you do not set the Auto Off function, press and hold
until the display disappears each time
you turn the ignition off.
1
Remove the screws from both sides of the unit.
2
Choose a screw hole from , or on each
frame .
If you secure the frames with the screw holes (default position),
it will maximize the projecting part of the unit. On the other hand,
screw holes will minimize the projecting part.
3
Reattach the frames with the selected screw
holes with the removed screws .
Notes
Choose the same screw hole position on both frames.
If you intend to secure the frames with screw holes or , make sure
that there is enough space in the dashboard of your car for the unit.
Dashboard
Size:
5 × max. 8 mm
(
7
/
× max.
5
/
in)
32
16
Reset button
When the installation and connections are completed, be
sure to press the reset button with a ballpoint pen, etc.
Advertisement
