Sony XAV-701BT Installation/Connections

4-422-719-11(1)
AV Center
Installation/Connections
XAV-701BT/XAV-741
  
  
× 2
× 2
 
× 8
× 2

(XAV-701BT only)
a b c
Equipment used in illustrations (not supplied)
Front speaker Rear speaker Power amplifier
Subwoofer iPod Rear view camera
Monitor Smartphone
A
FRONT AUDIO
OUT
REAR OUT
Z×Z L / R
SUB OUT REAR AUDIO
OUT
B
AUX AUDIO
IN
Video camera*
AUX IN
( VIDEO )
CAMERA
* not supplied
Cautions Connection diagram
 Run all ground (earth) leads to a common ground  To a common ground (earth) point
(earth) point.
First connect the black ground (earth) lead, then connect the yellow
 This unit is designed for negative ground (earth) 12 V and red power supply leads.
 To the power antenna (aerial) control lead or the
DC operation only.
 Do not disassemble or modify the unit. power supply lead of the antenna (aerial) booster
 Do not install in locations which interfere with airbag
Notes
 It is not necessary to connect this lead if there is no power antenna
operation.
(aerial) or antenna (aerial) booster, or with a manually-operated
 Do not get the leads under a screw, or caught in moving
telescopic antenna (aerial).
parts (e.g. seat railing).
 If your car has a built-in FM/AM antenna (aerial) in the rear/side
 Before making connections, turn the car ignition off to
glass, see "Notes on the control and power supply leads."
avoid short circuits.
To AMP REMOTE IN of an optional power
 Connect the yellow and red power supply leads only
amplifier
after all other leads have been connected.
This connection is only for amplifiers. Connecting any other system
 Be sure to insulate any loose unconnected leads with may damage the unit.
electrical tape for safety.  To a car's illumination signal
 Do not press on the LCD when installing the unit. Be sure to first connect the black ground (earth) lead to a common
ground (earth) point.
 Install the unit with the monitor facing straight forward;
 To the +12 V power terminal which is energized
do not install it at a slanted angle.
when the ignition switch is set to the accessory
Notes on the power supply lead (yellow)
position
 When connecting this unit in combination with other
Notes
stereo components, the amperage rating of the car
 If there is no accessory position, connect to the +12 V power
circuit to which the unit is connected must be higher
(battery) terminal which is energized at all times.
than the sum of each component's fuse amperage rating. Be sure to first connect the black ground (earth) lead to a common
ground (earth) point.
 If no car circuits are rated high enough, connect the unit
 If your car has a built-in FM/AM antenna (aerial) in the rear/side
directly to the battery.
glass, see "Notes on the control and power supply leads."
 To the +12 V power terminal which is energized
at all times
Parts list
Be sure to first connect the black ground (earth) lead to a common
ground (earth) point.
 To the parking brake switch cord
 The numbers in the list correspond to those in the
 To an auxiliary device such as a portable media
instructions.
 The bracket  is attached to the unit before shipping. player, game console, etc. (not supplied)
Before mounting the unit, use the release keys  to Tip
You can use an RCA pin cord (not supplied) to connect auxiliary
remove the bracket  from the unit. For details, see
devices.
"Removing the bracket ()" on the reverse side of the
 To the +12 V power terminal of the car's rear lamp
sheet.
lead (only when connecting the rear view
 Keep the release keys  for future use as they are
camera)
also necessary if you remove the unit from your
car. Notes on the control and power supply leads
 The screws  and frames  are attached to the unit  REM OUT lead (blue/white striped) supplies +12 V DC when you turn on
the unit.
before shipping. For details, see "Adjusting the frames
 If your car has built-in FM/AM antenna (aerial) in the rear/side glass,
()" on the reverse side.
connect REM OUT lead (blue/white striped) or the accessory power
 For XAV-701BT only: Assemble the parts of the
supply lead (red) to the power terminal of the existing antenna (aerial)
microphone  before use. For details, see "Installing the booster. For details, consult your dealer.
 A power antenna (aerial) without a relay box cannot be used with this
microphone (XAV-701BT only) ()" on the reverse
unit.
side.
Memory hold connection
Caution When the yellow power supply lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned off.
Handle the bracket  carefully to avoid injuring your
Notes on speaker connection
fingers.
 Before connecting the speakers, turn the unit off.
Catch  Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities to avoid damage.
 Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speakers.
 Do not connect the ground (earth) lead of this unit to the negative (–)
terminal of a speaker.
 Do not attempt to connect the speakers in parallel.
 Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
 To avoid a malfunction, do not use the built-in speaker leads installed in
your car if they feature a common negative (–) lead for the right and left
speakers.
 Do not connect the unit's speaker leads to each other.
Notes on connection

 If "Output connection failure." appears in the display, make sure the
speaker and amplifier are connected correctly.
Note  To use the monitor for the rear seats, connect the parking brake switch
cord to the ground (earth).
Before installing, make sure that the catches on both sides of the bracket
 are bent inwards 3.5 mm (
5 / in). If the catches are straight or bent
32
outwards, the unit will not be installed securely and may spring out.
Connection example
Notes (-A)
 Be sure to connect the ground (earth) lead before connecting the
amplifier.
 The alarm will only sound if the built-in amplifier is used.
Note (-B)
You cannot use multiple auxiliary devices simultaneously, even if they are
connected to different terminals.
Black Orange/white striped
REM OUT
Blue/white striped Red
Max. supply current: 0.4 A
Yellow
Light green
* 4
AUX2 AUDIO
IN

AUX2 IN
XAV-701BT
EXT
From car antenna (aerial)
8
REMOTE IN*
Fuse (10 A)
XAV-701BT only
3
MIC IN*
REAR OUT

 *
2
*
4
FRONT
AUDIO OUT
AUX1 AUDIO
IN
*
4
* 4
REAR SUB OUT
AUDIO OUT
ILLUMINATION
*
5
PARKING BRAKE
White
Left
White/black striped
Gray
Right
Gray/black striped
*
1
Green
Green/black striped
Left
Purple
Purple/black striped
Right
* 6
*
9
AUX1 IN
*
9
CAMERA
*
4
Z×Z L / R* 7
REVERSE IN
* 4
* 1 Speaker impedance: 4 – 8 ohms × 4 * 5 For details on connecting to the parking
* The microphone is supplied with brake switch cord, see "Connecting the
2
XAV-701BT only. For details on installing parking brake lead ()" on the reverse
the microphone, see "Installing the side.
microphone (XAV-701BT only) ()" on * not supplied
6
the reverse side. * 7 The sound is output from this terminal
* 3 The microphone input cord is available only when ZONE x ZONE is activated.
on XAV-701BT only. Whether in use or This terminal outputs a fixed level
not, route the microphone input cord regardless of the volume control of the
such that it does not interfere with unit.
driving. Secure the cord with a clamp, * A separate adaptor may be required.
8
etc., if it is installed around your feet. * 9 USB connection cable RC-202IPV (not
* 4 RCA pin cord (not supplied) supplied). To connect an iPod via
RC-202IPV, make sure to connect the
video output plug to AUX1 IN.