Sony XAV-701BT Installation/Connections

4-422-719-31(1)
AV Center
Installation/Connections
XAV-701BT
  
  
× 2
  
× 2 × 8
× 2

a b c
Equipment used in illustrations (not supplied)
Front speaker Rear speaker Power amplifier
Subwoofer iPod Rear view camera
Monitor Smartphone
A
FRONT AUDIO
OUT
REAR OUT
Z×Z L / R
SUB OUT REAR AUDIO
OUT
B
AUX AUDIO
IN
Video camera*
AUX IN
( VIDEO )
CAMERA
* not supplied
Cautions Connection diagram
 Run all ground (earth) leads to a common ground  To AMP REMOTE IN of an optional power
(earth) point. amplifier
 This unit is designed for negative ground (earth) 12 V
This connection is only for amplifiers. Connecting any other system
DC operation only. may damage the unit.
 To the parking brake switch cord
 Do not disassemble or modify the unit.
 Do not install in locations which interfere with airbag  To an auxiliary device such as a portable media
operation. player, game console, etc. (not supplied)
 Do not get the leads under a screw, or caught in moving
Tip
parts (e.g. seat railing).
You can use an RCA pin cord (not supplied) to connect auxiliary
 Before making connections, turn the car ignition off to devices.
avoid short circuits.  To the +12 V power terminal of the car's rear lamp
 Connect the power supply connection cable  to the lead (only when connecting the rear view
camera)
unit and speakers before connecting it to the auxiliary
power connector.
 Be sure to insulate any loose unconnected leads with
Warning
electrical tape for safety.
 Do not press on the LCD when installing the unit. If you have a power antenna (aerial) without a relay box,
 Install the unit with the monitor facing straight forward; connecting this unit with the supplied power supply
do not install it at a slanted angle.
connection cable  may damage the antenna (aerial).
Notes on the power supply lead (yellow) Notes on the control and power supply leads
 The power antenna (aerial) control lead (blue) supplies +12 V DC when
 When connecting this unit in combination with other
you turn on the tuner, or when you activate the AF (Alternative
stereo components, the amperage rating of the car
Frequency) or TA (Traffic Announcement) function.
circuit to which the unit is connected must be higher
 If your car has a built-in FM/MW/LW antenna (aerial) in the rear/side
than the sum of each component's fuse amperage rating. glass, connect the power antenna (aerial) control lead (blue) or the
accessory power supply lead (red) to the power terminal of the antenna
 If no car circuits are rated high enough, connect the unit
(aerial) booster. For details, consult your car dealer.
directly to the battery.
 A power antenna (aerial) without a relay box cannot be used with this
unit.
Memory hold connection
Parts list
When the yellow power supply lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned off.
Notes on speaker connection
 The numbers in the list correspond to those in the
 Before connecting the speakers, turn the unit off.
instructions.
 Use speakers with an impedance of 4 to 8 ohms, and with adequate
 The bracket  is attached to the unit before shipping. power handling capacities to avoid damage.
Before mounting the unit, use the release keys  to  Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speakers.
remove the bracket  from the unit. For details, see
 Do not connect the ground (earth) lead of this unit to the negative (–)
"Removing the bracket ()" on the reverse side of the
terminal of a speaker.
sheet.
 Do not attempt to connect the speakers in parallel.
 Keep the release keys  for future use as they are  Connect only passive speakers. Connecting active speakers (with
also necessary if you remove the unit from your built-in amplifiers) to the speaker terminals may damage the unit.
 To avoid a malfunction, do not use the built-in speaker leads installed in
car.
your car if they feature a common negative (–) lead for the right and left
 The screws  and frames  are attached to the unit
speakers.
before shipping. For details, see "Adjusting the frames
 Do not connect the unit's speaker leads to each other.
()" on the reverse side.
Notes on connection
 Assemble the parts of the microphone  before use. For
 If "Output connection failure." appears in the display, make sure the
details, see "Installing the microphone ()" on the speaker and amplifier are connected correctly.
 To use the monitor for the rear seats, connect the parking brake switch
reverse side.
cord to the ground (earth).
Caution
Handle the bracket  carefully to avoid injuring your
fingers.
Catch

Note
Before installing, make sure that the catches on both sides of the bracket
 are bent inwards 3.5 mm ( 5 / in). If the catches are straight or bent
32
outwards, the unit will not be installed securely and may spring out.
Connection example
Notes (-A)
 Be sure to connect the ground (earth) lead before connecting the
amplifier.
 The alarm will only sound if the built-in amplifier is used.
Note (-B)
You cannot use multiple auxiliary devices simultaneously, even if they are
connected to different terminals.
* 1 For details on installing the microphone, see "Installing the microphone ()" on the
reverse side.
* If your car antenna (aerial) is an ISO (International Organization for Standardization)
2
type, use the supplied adaptor  to connect it. First connect the car antenna (aerial) to
the supplied adaptor, then connect the adaptor  to the antenna (aerial) jack of the
unit.
* 3 Whether in use or not, route the microphone input cord such that it does not interfere
with driving. Secure the cord with a clamp, etc., if it is installed around your feet.
* 4 RCA pin cord (not supplied)
* 5 For details on connecting to the parking brake switch cord, see "Connecting the parking
brake lead ()" on the reverse side.
* 6 Speaker impedance: 4 – 8 ohms × 4
* The sound is output from this terminal only when ZONE x ZONE is activated. This terminal
7
outputs a fixed level regardless of the volume control of the unit.
* 8 A separate adaptor may be required.
* Not supplied
9
* 10 USB connection cable RC-202IPV (not supplied). To connect an iPod via RC-202IPV, make
sure to connect the video output plug to AUX1 IN.
AMP REM
Max. supply current: 0.3 A Blue/white striped
PARKING BRAKE Light green
*
5
AUX2 AUDIO
AUX2 IN
*
4
IN
EXT
*
2 From car antenna (aerial)

8
REMOTE IN*
Fuse (10 A)
MIC IN* 3
REAR OUT

 * 1
*
4
FRONT
AUDIO OUT
AUX1 AUDIO
IN
* 4
REAR SUB OUT
AUDIO OUT
For details, see "Power connection diagram" on the reverse side.
From the car's power connector
* 6
From the car's speaker connector

*
9
* 10
AUX1 IN
* 10
CAMERA
* 4
Z×Z L / R* 7
REVERSE IN
* 4
*
4
4 Yellow Continuous power supply
5 Blue Power antenna (aerial) control
6 Orange/white Switched illumination power supply
7 Red Switched power supply
8 Black Ground (earth)
Positions 1, 2, and 3 do not have pins.
1 + Speaker, rear, right
Purple
2 – Speaker, rear, right
3 + Speaker, front, right
Gray
4 – Speaker, front, right
5 + Speaker, front, left
White
6 – Speaker, front, left
7 + Speaker, rear, left
Green
8 – Speaker, rear, left
Negative polarity positions 2, 4, 6, and 8 have striped leads.