THUNDER TIGER MINI TITAN V2 - MANUAL 2 Instruction Manual page 34

BASIC CONCEPT OF ADJUSTMENT /
Before starting, make sure the following preparation is done.
1. Set all trims, knobs, and switches to the neutral and zero position.
2. Reset the radio to its factory preset position.
3. Choose the 120°E-CCPM swashplate control mode.
Reversing/Swash Mixing
The moving direction of servos has to be confirmed. You can attach the servo arms to the servos
temporarily so that it makes it easier to see the servos moving direction. While giving a positive collective
pitch, all of the 3 servos are supposed to be moving in the same direction to descend the swashplate. If the
3 servos are moving in the same direction but to raise the swashplate, you have to use the "swash
mixing" function to make it descend. If any of the servos is moving contrary, you have to adjust the one by
"reverse" function. Since the moving manner above is determined, the "reverse" function of
Aile/Elev/AUX is done.
Next, you have to check the control surface. While giving a cyclic pitch control, the swashplate has to be
tilted toward the correct direction. If not, you have to adjust it by "swash mixing" function. For example, if
a down elevator command is given, the swashplate is supposed to be tilted forward. If the swashplate is
tilted rearward, you have to change the +/- of the elevator control surface by "swash mixing" function. So
as the aileron control surface.
To sum up, the "reverse" function is to adjust the servo itself, and the +/- of the "swash mixing"
function is to adjust the control surface.
Servo Arms
After the moving direction of the servos is determined, please center the collective control stick. With the
collective control stick is centered, install the servo arms of the 3 servos. They are supposed to be level. If
the servo arms tilt with a small degree, use the "sub trim" function to adjust it independently. Thus the
procedure of centering is complete.
開始設定之前，請先確認下列注意事項
1. 發射機上所有的調整旋鈕、機構均位於中立點。
2. 重新設定原廠內建數據。
3. 選擇E-CCPM 120°模式。
正逆轉/十字盤混控設定
開啟電源確認伺服機運作方向是否正確，您可以觀察伺服機擺臂作動方向來判斷。發射機送出正螺距指令，三顆混控
伺服機運作方向應一致，來下拉十字盤。假設伺服機運作方向一致，但是卻推舉十字盤，此時必須使用十字盤混控設
定功能來調整。若是有單獨伺服機運作方向相反，此時應調整單一伺服機正逆轉方向。上述調整工作完成後，即完成
十字盤混控設定。
接下來，確認控制介面設定。利用發射機指令來確認十字盤混控系統是否正確運作，如不正確，請調整十字盤混控設
定。假設執行升降舵向下指令時，十字盤應該向前傾斜，如果呈現向後傾斜，必須在十字盤混控設定功能裡，修改設
定升降舵+/-。副翼調整方式同上。
正逆轉功能（reverse）為單獨調整伺服機用，調整介面需使用十字盤混控設定。
伺服機擺臂
伺服機運作方向正確無誤後，請將所有撥桿調回中立點位置，將伺服機擺臂與連桿相互垂直地安裝至伺服機上。如果
有些微差距，可利用副微調裝置完成設定。
-33-