Directed Electronics ProSecurity SR6000 Installation Manual page 47

3 3 - - 4 4 P P A A R R K K I I N N G G L L I I G G H H T T S S F F L L A A S S H H I I N N G G / / C C O O N N S S T T A A N N T T : : In the default setting, the unit will flash the vehicle's parking lights
(if connected) while remote started. The constant setting will turn the parking lights on solid for the entire run
duration.
3 3 - - 5 5 C C R R A A N N K K T T I I M M E E 0 0 . . 6 6 / / 0 0 . . 8 8 / / 1 1 . . 0 0 / / 1 1 . . 2 2 / / 1 1 . . 4 4 / / 1 1 . . 6 6 / / 1 1 . . 8 8 / / 2 2 . . 0 0 / / 4 4 . . 0 0 S S E E C C O O N N D D S S : : If the unit is programmed for no engine check-
ing or voltage sense, the crank time must be set to the appropriate duration. The default setting is 0.6 second.
If a different crank time is desired, select feature 3-5 and select either 0.6 second by using the one-chirp setting
or toggle through the higher settings by using the two-chirp settings.
3 3 - - 6 6 V V O O L L T T A A G G E E C C H H E E C C K K H H I I / / L L O O W W : : This feature only functions when programmed for voltage sense. Some vehicles have
many accessories, which are turned on when remote started. In these vehicles, the variation of voltage between
the engine off and the car running is very small and the remote start unit may "think" the vehicle has not started.
This can cause the remote start to shut-down after the car has been started. If this happens program this feature
to the LOW position.
3 3 - - 7 7 S S H H O O R R T T R R U U N N / / T T U U R R B B O O : : When the
vehicle will start for the programmed short run time. The factory default is 1 minute.
3 3 - - 8 8 A A C C T T I I V V A A T T I I O O N N P P U U L L S S E E C C O O U U N N T T : : This allows the system to use 1 or 2 pulses to activate the remote start sequence.
N N o o t t e e ! ! 1 or 2 pulses on the WHITE/BLUE remote start activation input wire as well as the
button of the remote control.
3 3 - - 9 9 2 2 n n d d I I G G N N I I T T I I O O N N / / 2 2 n n d d A A C C C C E E S S S S O O R R Y Y O O U U T T P P U U T T : : This will allow the PINK/WHITE to be used as a 2 nd ignition or an
accessory.
3 3 - - 1 1 0 0 A A C C C C E E S S S S O O R R Y Y S S T T A A T T E E D D U U R R I I N N G G W W A A I I T T - - T T O O - - S S T T A A R R T T : : This feature will allow the selection of the accessory output to
be ON or OFF during wait-to-start.
3 3 - - 1 1 1 1 2 2 n n d d S S T T A A T T U U S S O O U U T T P P U U T T : : This feature will allow selection of status output or a rear defogger mode that turns
on ten seconds after the vehicle has started. The defogger mode has two selections, latched or pulsed. Latched
mode will only stay on for 10 minutes.
3 3 - - 1 1 2 2 A A N N T T I I - - G G R R I I N N D D O O N N / / O O F F F F : : With the anti-grind On (default) the ground-when-armed output will be active during
remote start operation. If accessories such as a voice module or window module are added to the unit, it may be
necessary to program this feature off.
and buttons on the transmitter are pressed simultaneously, the
4 4 7 7