Advertisement
Quick Links
US
Technical Support and E-Warranty Certificate
www.vevor.com/support
UTILITY SINK PUMP
INSTRUCTIONS
MODEL: FLO500-RD
We continue to be committed to provide you tools with competitive price.
"Save Half", "Half Price" or any other similar expressions used by us only represents an
estimate of savings you might benefit from buying certain tools with us compared to the major
top brands and does not necessarily mean to cover all categories of tools offered by us. You
are kindly reminded to verify carefully when you are placing an order with us if you are
actually saving half in comparison with the top major brands.
Advertisement
Related Manuals for VEVOR FLO500-RD
Summary of Contents for VEVOR FLO500-RD
- Page 1 UTILITY SINK PUMP INSTRUCTIONS MODEL: FLO500-RD We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us.
- Page 2 This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product.
- Page 3 The pump must be connected to a GFCI protected plug which has been installed according to regulations. The plug must have a supply voltage of AC110-120V 60Hz. SPECIFICATION PARAMETERS Model Input Max Flow Max Lift Outlet size Power AC110-120V FLO500-RD 1/2 HP 1750 GPH 18 ft 1”、1-1/4” 1-1/2" 60Hz - 2 -...
- Page 4 CAUTION This pump has been evaluated for use with water only. IMPORTANT!For your own safety-before starting to run the pump,please have the following items checked by an expert: following items checked by an expert: 1.Risk of electric shock-This pump is supplied with a grounding conductor and grounding-type attachment plug.To reduce the risk of electric shock,be certain that it is connected only to a properly grounded,grounding-type receptacle.
- Page 5 swimming pool areas. 3.The electrical connections must be protected from moisture. 4.If there is danger of flooding,the electrical connections must betaken to higher ground. 5.Circulation of caustic fluids,as well as the circulation of abrasive materials,must be avoided at all costs. 6.The pump must be protected from frost.
- Page 6 easy access for repair and maintenance and in accordance with local plumbing code. Connection to side inlets As shown in the picture above, the pump has two side inlets (one on each side) that are meant to connect additional fixtures. To connect to the side inlets, one rubber coupling (1-1/2”x2”) is provided along with the clamps.
- Page 7 rubber coupling (with clamps) will be needed if you want to use the other top inlet. If one of the top inlets is not being used, a cap is provided to cover this inlet. Connection to a bathtub / shower When adding a bathtub / shower, a base will have to be constructed.
- Page 8 (instructions intended for professionals only) Disconnect the power supply before attempting any work on the device. This device does not require any specific maintenance. In case service is required, any work on the device must be carried out by a technician. OPERATION After reading these instructions,consider the following points before starting the pump:...
- Page 9 PART DRAWING REPAIR GUIDE Problem Cause Solution The motor runs The discharge pipe is Clean the discharge pipe . normally, but the blocked. water drains Inspect the check valve. Possible that the slowly. check valve is half closed. The water drains slowly and the motor works Ventilation system blocked.
- Page 10 The motor hums A foreign body is blocking the and it does not Contact an authorized technician. impeller. Faulty capacitor. evacuate the water. The water doesn’t evacuate Evacuation pipe blocked. Contact an authorized technician. and the motor runs for a long Partially blocked impeller.
- Page 11 Technical Support and E-Warranty Certificate www.vevor.com/support...
Need help?
Do you have a question about the FLO500-RD and is the answer not in the manual?
Questions and answers