Table of Contents
Advertisement
Quick Links
GENERAL MANUAL FOR
•
This pr
This pr
oduct is not equipped with a spark arr
oduct is not equipped with a spark arr
This pr
This product is not equipped with a spark arr
This pr
oduct is not equipped with a spark arr
oduct is not equipped with a spark arresting muf
materials, or on land covered with materials such as agricultural crops, forest, brush, grass, or other similar
items, then an approved spark arrester must be installed and is legally required in the state of California. It is a
violation of California statutes section 130050 and/or sections 4442 and 4443 of the California Public Resources
Code, unless the engine is equipped with a spark arrestor, as defined in section 4442, and maintained in effective
working order. Spark arresters are also required on some U. S. Forest service land and may also be legally
required under other statutes and ordinances.
•
Engine exhaust from this product contains chemicals known, in certain quantities, to cause cancer, birth defects or
other reproductive harm.
MG4-OLENG-2B 5/1/99
OIL LUBRICATED
SINGLE STAGE
GASOLINE ENGINE
AIR COMPRESSOR
esting muf
esting muf
fler. . . . . If the product will be used around flammable
fler
fler
esting muffler
esting muf
fler
213 Industrial Dr. • Jackson, TN 38301
Advertisement
Table of Contents
Related Manuals for DeVilbiss MG4-OLENG-2B
Summary of Contents for DeVilbiss MG4-OLENG-2B
- Page 1 • Engine exhaust from this product contains chemicals known, in certain quantities, to cause cancer, birth defects or other reproductive harm. MG4-OLENG-2B 5/1/99 esting muf esting muf fler fler..If the product will be used around flammable...
-
Page 2: Table Of Contents
Installing Handle, Foot Extension Bracket, Wheels, Outlet Valve ... 8 INSTALLATION AND BREAK-IN PROCEDURES ... 9-11 Location of the Air Compressor ... 9 Permanent Installation ... 9 Lubrication, Oil and Gasoline ... 9-10 Break-in Procedures ...10-11 SAFETY GUIDELINES - DEFINITIONS This manual contains information that is important for you to know and understand. -
Page 3: Warranty Statement
All decisions of DeVilbiss Air Power Company/ExCell Manufacturing with regard to this policy shall be final. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. -
Page 4: Warning Chart
IMPORTANT SAFETY INSTRUCTIONS IMPROPER OPERATION OR MAINTENANCE OF THIS PRODUCT COULD RESULT IN SERIOUS INJURY AND PROPERTY DAMAGE. READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. HAZARD GASOLINE AND GASOLINE VAPORS CAN RISK OF BECOME IGNITED BY COMING INTO CON- EXPLOSION OR FIRE TACT WITH HOT COMPONENTS SUCH AS THE MUFFLER, FROM ENGINE EXHAUST GASES,... - Page 5 AND BLEED PRESSURE FROM THE AIR HOSE AND TANK BEFORE ATTEMPTING MAINTENANCE, ATTACHING TOOLS OR ACCESSORIES. ALWAYS OPERATE AIR COMPRESSOR IN A CLEAN, WELL VENTILATED AREA. AVOID ENCLOSED AREAS SUCH AS GARAGES, BASEMENTS, STORAGE SHEDS, ETC., WHICH LACK A STEADY EXCHANGE OF AIR. NEVER OPERATE UNIT IN ENCLOSED LOCATIONS OCCUPIED BY HUMANS OR ANIMALS.
-
Page 6: Glossary
California Code. All DeVilbiss Air Power manufactured air compressors should be operated on not more than a 50% duty cycle. This means an air compressor that pumps more than 50% of one hour, is considered misuse, because the air compressor is undersized for the required air demand. -
Page 7: Description Of Operation
For the location or a listing of the nearest DeVilbiss Air Power Authorized Warranty Service Center, call our toll free number at 1-800-888-2468, Ext. 2, and talk with... -
Page 8: Assembly Instructions
It may be necessary to brace or support one end of the outfit when attaching the wheels and the foot extension bracket because the air compressor will have a tendency to tip before both wheels are assembled. EXCESSIVE TANK VIBRATION CAN WEAK- EN THE AIR TANK AND CAUSE RUPTURE OR EXPLOSION. -
Page 9: Installation And Break-In Procedures
MONOXIDE WHICH IS ODORLESS AND TOXIC. OPERATE ENGINE IN WELL VENTI- LATED AREAS ONLY. Operate the air compressor in a clean, dry and well ventilated area. The air intake filter must be kept clear of obstructions that could interfere with the flow of air through the fan bladed flywheel. -
Page 10: Break-In Procedures
INSTALLATION AND BREAK-IN PROCEDURES For your convenience, purchase a 1/4" NPT nipple, 2 1/2" long, and a 1/4" NPT x 1/4" NPT coupling (pipe collar) to allow ease in draining oil. Remove oil drain plug on the gas tank side of the engine and install the nipple. Thread the coupling on the end of the nipple and screw the drain plug in the coupling. -
Page 11: Break-In Procedures
INSTALLATION AND BREAK-IN PROCEDURES 2. Place your left hand on the air compressor handle, and your right hand on the starter handle, and pull cord out quickly to overcome engine compression and prevent "kickback". If engine does not start, push the choke about three-quarters of the way in or choke lever three quarters to the left and pull starter handle again. -
Page 12: Maintenance
NEVER OPERATE THE COMPRESSOR WITH THE BELT GUARD REMOVED. To ensure efficient operation and longer life of the air compressor outfit, a routine maintenance schedule should be prepared and followed. The following routine maintenance schedule is geared to an outfit in a normal working environment operating on a daily basis. -
Page 13: Air Compressor
A clean air compressor and engine run cooler and provide longer service. Clean or blow off fins and any other parts of the air compressor and engine that collect dust or dirt. Do not place tags, containers or other material on or against the ventilation openings in the belt guard. -
Page 14: Engine - Oil Change And Air Cleaner
Engine - Oil Change and Air Cleaner See Briggs & Stratton "Operating and Maintenance Instructions" for information regarding engine oil changes and air cleaner service as well as for warranty informa- tion. Engine - Adjustments Read the Briggs & Stratton "Operating and Maintenance Instructions"... -
Page 15: Belt - Replacement
Storage Before You Store The Air Compressor: 1. Review the "Operating Procedures" and "Mainte- nance" sections on the preceding pages and per- form maintenance as necessary. -
Page 16: Troubleshooting Guide
TROUBLESHOOTING GUIDE PERFORMING TROUBLESHOOTING OR REPAIRS CAN EXPOSE MOVING PARTS OR COMPRESSED AIR SOURCES. PERSONAL INJURY MAY OCCUR. PRIOR TO ATTEMPTING ANY TROUBLESHOOTING OR REPAIRS, THE ENGINE SPARK PLUG WIRE SHOULD BE REMOVED. NEVER OPERATE THE OUTFIT WITH THE BELT GUARD REMOVED. THE BELT GUARD SHOULD BE REMOVED ONLY WHEN THE SPARK PLUG WIRE IS REMOVED. - Page 17 TROUBLESHOOTING GUIDE PROBLEM CAUSE Compressor is not supplying Prolonged excessive use of air. enough air to operate accesso- ries. Compressor is not large enough for air requirement. Restricted air intake filter. Loose belt. Hole in hose. Check valve restricted. Air leaks. Excessive belt wear.
-
Page 18: Service Notes
SERVICE NOTES... - Page 19 SERVICE NOTES...
- Page 20 The warranty can be found in the General Manual or is available upon request. Attach Sales Receipt Here Retain Original Sales Receipt as Proof of Purchase for Warranty Repair Work. DeVilbiss Air Power Company • 213 Industrial Dr. • Jackson, TN 38301...