Speaker Setup - Onkyo HT-RC470 Instruction Manual

Speaker Setup

1 2 3 4
"Setup"
Main Menu Speaker Setup
Some of the settings in this section are set automatically
by Audyssey 2EQ ® Room Correction and Speaker Setup
(➔ page 32).
Here you can check the settings made by Audyssey 2EQ
Room Correction and Speaker Setup function, or set them
manually, which is useful if you change one of the
connected speakers after using Audyssey 2EQ Room
Correction and Speaker Setup function.
Speaker Settings
If you change these settings, you must run
Audyssey 2EQ Room Correction and Speaker Setup
(➔ page 32).
again
If you bi-amp the front speakers, you must change the
"Speakers Type (Front)" setting. For details on speaker
wire connection, see "Bi-amping the Front Speakers"
(➔ page 13).
Note
• When bi-amping is used, the AV receiver is able to drive up to 5.1
speakers in the main room.
• Before you change these settings, turn down the volume.
■
Speakers Type (Front)
Normal:
Select this if you've connected your front speakers
normally.
Bi-Amp:
Select this if you've bi-amped your front speakers.
■
Powered Zone 2
No
Yes:
5
Zone 2 speakers can be used. (Powered Zone 2
enabled).
Note
• If the "Speakers Type (Front)" setting is set to "Bi-Amp",
Powered Zone 2 cannot be used.
• When the "Powered Zone 2" setting is set to "Yes" and Zone 2
is turned on, the surround back and front high speakers cannot be
used.
Speaker Configuration
This setting is set automatically by Audyssey 2EQ Room
Correction and Speaker Setup
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify "Full Band" for speakers that can output low
frequency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover
frequency will be output by the subwoofer instead of the
speaker. Refer to your speaker's manuals to determine the
optimum crossover frequencies. If you set up your
speakers using Audyssey 2EQ Room Correction and
Speaker Setup, please make sure manually that any THX
speakers are set to "80Hz(THX)" crossover.
■
Subwoofer
Yes
No
■
Front
Full Band
40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz, 200Hz
Note
• If the "Subwoofer" setting is set to "No", the "Front" setting is
fixed at "Full Band".
(➔ page 32).
En-52
Advanced Operations
■
Center , Surround
*1 *1
Full Band
40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz, 200Hz
None
■
Front High
*1*2*3*5
Full Band
40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz, 200Hz
None
■
Surround Back
*1*2*3*4
Full Band
40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz, 200Hz
None
Note
*1 "Full Band" can be selected only when "Full Band" is
selected in the "Front" setting.
*2 If the "Surround" setting is set to "None", this setting cannot
be selected.
*3
If the "Speakers Type (Front)" setting is set to "Bi-Amp", or
the "Powered Zone 2" setting is set to "Yes" together with
Zone 2 turned on, this setting cannot be selected.
*4 If anything else than "None" is selected in "Front High", this
setting is automatically set to "None".
*5 If anything else than "None" is selected in "Surround Back",
this setting is automatically set to "None".
■
Surround Back Ch
1ch:
Select if only one surround back speaker L is
connected.
2ch:
Select if two (left and right) surround back speakers
are connected.
Note
• If the "Surround Back" setting is set to "None", this setting
cannot be selected.
• If the "Powered Zone 2" setting is set to "Yes" and Zone 2 is
turned on, this setting cannot be selected.