Onkyo HT-RC460 Instruction Manual
  1. Manuals
  2. Brands
  3. Onkyo Manuals
  4. Receiver
  5. HT-RC460
  6. Instruction manual

Onkyo HT-RC460 Instruction Manual

Owner manual
Hide thumbs Also See for HT-RC460:
Table of Contents

Advertisement

Quick Links

Enlarged version
AV RECEIVER
HT-RC460
Instruction Manual
Contents

Table of Contents ...........................................5

Connections .................................................11
Turning On & Basic Operations..................19
Advanced Operations ..................................43
Controlling Other Components...................66
Appendix .......................................................73
Internet Radio Guide
Remote Control Codes
E
n

Advertisement

Table of Contents
loading

Related Manuals for Onkyo HT-RC460

Summary of Contents for Onkyo HT-RC460

  • Page 1: Table Of Contents

    Contents AV RECEIVER Safety Information and Introduction ....2 HT-RC460 Table of Contents ...........5 Connections ..........11 Turning On & Basic Operations....19 Instruction Manual Advanced Operations ........43 Controlling Other Components....66 Appendix ............73 Internet Radio Guide Remote Control Codes...

  • Page 2: Safety Information And Introduction

    Important Safety Instructions exposed to rain or moisture, does not operate normally, Leave 20 cm (8") of free space at the top and sides and 1. Read these instructions. or has been dropped. 10 cm (4") at the rear. The rear edge of the shelf or 2.

  • Page 3: Precautions

    For models having a power cord with a polarized plug: • If you do not use this unit for a long time, it may not requirements printed on the unit’s rear panel (e.g., AC...

  • Page 4: Supplied Accessories

    • If the remote controller doesn’t work reliably, try replacing the batteries. • Don’t mix new and old batteries or different types of batteries. • If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion.

  • Page 5: Table Of Contents

    Using the Audio Settings of Quick Setup....44 Turning On & Basic Operations Using the Setup Menu (HOME) ........ 46 To reset the AV receiver to its factory defaults, turn it About the HYBRID STANDBY indicator ....47 on and, while holding down CBL/SAT, press Turning On/Off the AV Receiver ........19...

  • Page 6: Features

    Safety Information and Introduction Features Connections • 8 HDMI Inputs (1 on front panel) and 2 Outputs Amplifier • Onkyo p for System Control • 4 Digital Inputs (2 Optical/2 Coaxial) • 80 Watts/Channel @ 8 ohms (FTC) • Component Video Switching (1 Input/1 Output) •...

  • Page 7: Front & Rear Panels

    Front & Rear Panels Front Panel f g h i j k l For detailed information, see the pages in parentheses. k TUNING q/w (30), PRESET e/r (31), cursor and v HYBRID STANDBY indicator (47) a 8ON/STANDBY button (19) ENTER buttons...

  • Page 8: Display

    Z2 (Zone 2) indicator (65) HDMI indicator (60) b 3D indicator DIGITAL indicator This lights when a 3D input signal is detected. k ARC indicator (61) c Headphone indicator (42) l USB indicator (24, 25) d 1, 3 and cursor indicators (24)

  • Page 9: Rear Panel

    SUBWOOFER PRE OUT jacks e FM ANTENNA jack and AM ANTENNA terminal m MONITOR OUT V jack f HDMI IN and HDMI output (HDMI OUT MAIN and HDMI OUT SUB) jacks See “Connecting the AV Receiver” for connection g SPEAKERS terminals (➔...

  • Page 10: Remote Controller

    RETURN button k HOME button (40) l SLEEP button (41) ■ Controlling the tuner To control the AV receiver’s tuner, press AM or FM (or RECEIVER). a q/w buttons (30) b D.TUN button (30) c DISPLAY button d CH +/– button (31)

  • Page 11: Connections

    Screw-type speaker terminals Push-type speaker terminals Strip 1/2" to 5/8" (12 to 15 mm) of insulation from the ends Strip 3/8" to 1/2" (10 to 12 mm) of insulation from the ends If you’re using only one surround back speaker, connect it to...
  • Page 12 (+) side of each speaker cable in accordance with the table above. Then all you need to do is to match the color of each label to the corresponding speaker terminal. Speaker Connection Precautions Read the following before connecting your speakers: •...
  • Page 13 SUBWOOFER PRE OUT jacks respectively. The same signal is output from each jack. Front right Front left • If your subwoofer is unpowered and you’re using an external amplifier, connect the subwoofer pre out jack to an input on the amplifier. En-13...

  • Page 14: About Av Connections

    • The AV receiver does not support SCART plugs. video sockets slightly differently). • The AV receiver’s optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when it’s Green removed. Push plugs in all the way.

  • Page 15: Connecting Components With Hdmi

    ✔ Satellite/cable set-top box, etc. The Audio Return Channel (ARC) function enables an or the TV is set to another input source, this may result in no ✔ Game console HDMI capable TV to send the audio stream to HDMI OUT sound from the AV receiver or the sound may be cut off.

  • Page 16: Connecting Your Components

    VIDEO jack. Video signals input from VIDEO will be output from the MONITOR OUT and HDMI output jacks. receiver’s display when changing settings. Do not connect the AV receiver’s USB port to a USB port on ✔: Assignment can be changed (➔ page 49).

  • Page 17: Connecting Onkyo Ri Components

    • Some components may not support all u functions. Refer to the (➔ page 70). manuals supplied with your Onkyo components. • While Zone 2 is on, the System On/Auto Power On and Direct Change u functions do not work. En-17...

  • Page 18: Connecting The Antennas

    Indoor FM antenna (supplied) Note • Once your AV receiver is ready for use, you’ll need to tune into a radio station and position the antenna to achieve the best possible reception. • Keep the AM loop antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.

  • Page 19: Turning On & Basic Operations

    Receiver Press 8ON/STANDBY on the front panel. To ensure smooth operation, here’s a few easy steps to help you configure the AV receiver before you use it for the very first time. These settings only need to be made 8ON/STANDBY Press RECEIVER followed by 8RECEIVER on the once.

  • Page 20: Connections

    The automatic speaker setup is performed The on-screen menus appear only on a TV that is • Pressing HOME will close the setup wizard. To restart the initial following instructions on screen. Refer to step 2 connected to HDMI OUT MAIN.

  • Page 21: Source Connection

    Remote Mode Setup Network Connection This step checks the connection of source components. With this step, you can enter remote control codes for the This step checks your network connection. components you want to operate. Use q/w to select one of the following options, and Use q/w to select one of the following options, and then press ENTER.

  • Page 22: Playback

    • “iPod/iPhone Playback via Onkyo Dock” (➔ page 59). in the “Screen Saver” setting (➔ page • The screen will return to its previous state if the AV receiver is • “Controlling Other Components” (➔ page operated. To adjust the volume, use VOL q/w.

  • Page 23: Controlling Contents Of Usb Or Network Devices

    (➔ page 68). Pressing this button twice selects the previous song. Note • The buttons you can use will differ depending on the devices and This button fast-reverses the current song. media used for playback. This button pauses playback. SEARCH You can toggle between the playback screen and the list screen during playback.

  • Page 24: Understanding Icons On The Display

    USB device from the USB port. Repeat receiver cannot read the iPod/iPhone. • If you connect an iPod or iPhone to the USB port, no sound will be output from the headphones jack. Shuffle • When connecting your iPod/iPhone with a USB cable, we recommend you use an official USB cable from Apple Inc.

  • Page 25: Playing A Usb Device

    (➔ page 89). • “Network/USB Features” • In this mode, video contents are not displayed, even if they are input from the VIDEO jack on the AV receiver’s front panel. Press USB repeatedly to select the “USB(Front)” or “USB(Rear)” input.

  • Page 26: Listening To Vtuner Internet Radio

    (➔ page 89). The on-screen menus appear Radio. only on a TV that is connected to HDMI OUT MAIN. Adding to My Favorites The vTuner Internet Radio Service is a portal site featuring The selected program will be added to “My Favorites”...

  • Page 27: Registering Other Internet Radio

    AV receiver. Internet radio station, you may not be able to listen to some • If you want to add a new station directly from “My Favorites”, stations. select an empty slot in the list and press MENU. Then, select To listen to other Internet radio stations, you must register “Create New Station”...

  • Page 28: Playing Music Files On A Server

    Use q/w to select an item, and then press ENTER or 1 to start playback. This section explains how to configure Windows Media Player 11 so that the AV receiver can play the music files You need to connect the AV receiver to your home stored on your computer.

  • Page 29: Remote Playback

    “Remote Turn on the AV receiver. playback” window. This section explains how to configure Windows Media Player 12 so that the AV receiver can play the music files Start Windows Media Player 12. Note stored on your personal computer.

  • Page 30: Listening To Am/Fm Radio

    (Actual display depends on the country.) • Tuning into weak FM stereo stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to (Actual display depends on the country.) manual tuning mode and listen to the station in mono.
  • Page 31 Turning On & Basic Operations ■ Presetting AM/FM Stations Deleting Presets You can store a combination of up to 40 of your favorite Select the preset that you want to delete. AM/FM radio stations as presets. See the previous section.

  • Page 32: Using Basic Functions

    With the supplied calibrated microphone, Audyssey 2EQ ® or other devices. Turn off the cell phone (even if it is not in use) automatically determines the number of speakers microphone tip pointed directly at the ceiling using a or place it away from all audio electronics.
  • Page 33 Disconnect the speaker setup microphone. Note When prompted, repeat step 6. • The on-screen menus appear only on a TV that is connected to HDMI OUT MAIN. If your TV is connected to other Use q/w to select an option, and then press ENTER.
  • Page 34 Changing the Speaker Setup Manually ® You can manually make changes to the settings found While Audyssey 2EQ Room Correction and Speaker Setup is in progress, one of the error messages below may during Audyssey 2EQ Room Correction and Speaker appear. Setup. See also: 2EQ: Auto Setup •...

  • Page 35: Using The Listening Modes

    • The listening modes you can select depends on the format of the input signal. To check the format, see “Displaying Source Information” (➔ page 41). • While a pair of headphones is connected, you can select the following listening modes: Mono, Direct, and Stereo. En-35...
  • Page 36 The illustration shows which speakers are activated in each The AV receiver’s listening modes can transform your modes. channel. See “Speaker Configuration” for the speaker listening room into a movie theater or concert hall, with setup (➔ page 50). This is mono (monophonic) sound.
  • Page 37 Full Mono In this mode, all speakers output the same sound in mono, so the sound you hear is the F u l M o n o same regardless of where you are within the listening room.
  • Page 38 Input Speaker Source Layout Listening Mode Description Input Speaker In this mode, audio from the input source is Source Layout D XCN output without surround-sound processing. Direct In this mode, audio from the input source is D T S The speaker configuration (presence of output without surround-sound processing.
  • Page 39 Dolby Pro Logic II logo. the sound. The AV receiver can input the DSD signal from HDMI IN. Depending on the player, setting the • Dolby PLIIx Movie output on the player side to PCM might bring better sound.

  • Page 40: Using The Home Menu

    Using the Home Menu to play music files on a server, use q/w/e/r to • If no video signals are present, the thumbnails will be filled in select “DLNA” and then press ENTER. The Home menu provides quick access to frequently used black.

  • Page 41: Using The Sleep Timer

    The sleep time can be set from 90 to 10 minutes in 10 Press TV/CD or GAME. minute steps. “TV/CD” or “GAME” appears on the AV receiver’s The SLEEP indicator lights on the AV receiver’s...

  • Page 42: Using The Music Optimizer

    Stereo, unless it’s already set to Stereo, Mono, Direct. • If you connect an iPod or iPhone to the USB port on the AV Muting the AV Receiver receiver, no sound will be output from the headphones jack.

  • Page 43: Advanced Operations

    A u d i o V i d e o I n f o r m a t i o n L i s t e n i n g M o d e To be continued En-43...

  • Page 44: Using The Audio Settings Of Quick Setup

    Advanced Operations Speaker Levels Using the Audio Settings of Quick Note Setup • When the “Monitor Out” setting is set to “Sub”, “Video” cannot ■ Subwoofer Level be selected. –15dB to 0dB to +12dB in 1 dB steps You can change various audio settings from the Quick •...
  • Page 45 • The Late Night function can be used only when the input source is Dolby Digital, Dolby Digital Plus, or Dolby TrueHD. • The Late Night function is set to “Off” when the AV receiver is set to standby. For Dolby TrueHD sources, it will be set to “Auto”.

  • Page 46: Using The Setup Menu (Home)

    • The time until the screen saver activates itself can be changed RECEIVER in the “Screen Saver” setting (➔ page 59). • The screen will return to its previous state if the AV receiver is operated. a Main Menu ENTER b Sub Menu...

  • Page 47: About The Hybrid Standby Indicator

    BD/DVD (➔ page CBL/SAT GAME TUNER Note TV/CD • If Zones are turned on or, if a mobile device connected to the Front Input (MHL) is charging, the HYBRID STANDBY indicator won’t light. EXTRA1 EXTRA2 Miscellaneous Volume Setup (➔ page...

  • Page 48: Input/Output Assign

    HDMI4 ■ case select anything other than “1080p/24”. Monitor Out FRONT (Fixed) • With some TVs, there may be no picture when this setting is set Main: TV/CD - - - - - to “4K Upscaling”. Select this if your TV is connected to HDMI OUT •...
  • Page 49 • When composite video and component video sources are • When an HDMI IN is assigned to an input selector in • If you assign “- - - - -” to an input selector that is currently (➔ page 48), the same HDMI IN will be set as upconverted for HDMI OUT SUB, only signals with a resolution “HDMI Input”...

  • Page 50: Speaker Setup

    ■ Subwoofer Select if only one surround back speaker L is Note connected. • When bi-amping is used, the AV receiver is able to drive up to 5.1 2ch: speakers in the main room. ■ Front Select if two (left and right) surround back speakers •...
  • Page 51 “- - -”. • Speakers that you set to “No” or “None” in • When the “Powered Zone 2” setting is set to “Yes” and Zone 2 • This setting is set to “On” automatically when the “Subwoofer” (➔ page 50).

  • Page 52: Audio Adjust

    If you’re not using any surround back speakers, these The Height Gain Control in Dolby Pro Logic IIz enables settings apply to Dolby Pro Logic II, not Dolby Pro Logic the listener to select how much gain is applied to the front Main Menu Audio Adjust IIx.

  • Page 53: Source Setup

    Narrow: Note Select if the listening angle is less than 30 degrees. • When this setting is set to “Off”, the Late Night function for Preparation With this setting, you can optimize the Theater- Dolby TrueHD sources is automatically fixed to “Off”...
  • Page 54 The result is bass response, and 15 dB) that can be selected when the mix level of the Audyssey Dynamic EQ solves the problem of deteriorating tonal balance, and surround impression that remain content is not within the standard.
  • Page 55 When using progressive scanning on your Blu-ray Disc/DVD player, you may find that the picture and sound • To name a radio preset, select AM or FM, and then select the are out of sync. With this setting, you can correct this by –...
  • Page 56 With “Picture Mode”, you can change the following Full: movie. If it is a movie, the appropriate conversion is settings to be suitable for the movie or game screen by one applied. operation; “Game Mode”, “Film Mode”, “Edge The AV receiver will adjust to the picture source, Enhancement”, “Noise Reduction”, “Brightness”,...
  • Page 57 – “Monitor Out” is set to “Sub”. Note digital and analog inputs. This procedure can also be performed on the remote controller • The setting will be reset to “Off” when you change the setting in by using the Quick Setup (➔ page 43).

  • Page 58: Listening Mode Preset

    ■ DTS/DTS-ES/DTS-HD Listening Mode Preset Use q/w to select the signal format that you want to With this setting, you can specify the listening mode set, and then use e/r to select a listening mode. used when DTS or DTS-HD High Resolution format Only listening modes that can be used with each input digital audio signals are played (DVD, LD, CD, etc.).

  • Page 59: Miscellaneous

    Screen Saver With this setting, you can specify the volume setting to be • When this setting is changed, all radio presets will be deleted. used each time the AV receiver is turned on. 3 min, 5 min, 10 min To use the same volume level that was used when the AV receiver was turned off, select “Last”.
  • Page 60 Note • When the setting is set to “On” and the menu is closed, the names When enabling the HDMI Through function, regardless of • If “On” is selected and the audio can be output from the TV, the of connected p-compatible components and “RIHD On”...
  • Page 61 Note Note (➔ page and specify the preview display of HDMI • This setting is fixed to “- - - -” when the “HDMI • Set to “ On” , the Auto Standby function may activate itself during video streams.
  • Page 62 If your router’s DHCP server is enabled, you don’t need to Note Class B: change any of these settings, as the AV receiver is set to “172.16.0.0” to “172.31.255.255” • When set to “On”, the power consumption slightly increases in use DHCP to configure itself automatically by default (i.e.,...

  • Page 63: Remote Controller Setup

    ID from “1”, to “2” or “3”. Note • If you do change the AV receiver’s remote ID, be sure to change the remote controller to the same ID (see below), otherwise, you won’t be able to control it with the remote controller.

  • Page 64: Zone 2

    (➔ page 50). Zone 2 Note Receiver/ • With this setup, the volume of Zone 2 is controlled by the AV integrated amp receiver. • When Powered Zone 2 is used, playback in the main room is Note reduced to 5.1 channels.

  • Page 65: Controlling Zone 2 Components

    If your Zone 2 speakers are connected to a receiver or controller first. Main room and Zone 2 is set to share the same source, no sound integrated amplifier in Zone 2, use its volume control to will be output from Zone 2.

  • Page 66: Controlling Other Components

    • If you do adjust the volume control on your iPod/iPhone while When you turn on the AV receiver, the RI Dock and it’s inserted in the RI Dock, be careful that it’s not set too loud iPod/iPhone turn on automatically. In addition, when RI before you reconnect your headphones.

  • Page 67: Controlling Your Ipod/Iphone

    Dock on or off. Also, your iPod/iPhone may not respond the With the RI Control first time you press this button, in which case you should press Make an u connection and enter the remote control code it again. This is because the remote controller transmits the On 81993 (with u).

  • Page 68: Controlling Other Components

    If you cannot control the component, use q/w to enter the remote control code for a component that you • This can only be carried out using the on-screen menu. select “Try Next Code” and press ENTER. want to control: DVD, TV, CD, etc.

  • Page 69: Entering Remote Control Codes

    Note Within 30 seconds, use the number buttons to enter • If any other button than the colored buttons is pressed, the the 5-digit remote control code. operation will be cancelled. The remote indicator flashes twice.

  • Page 70: Remote Control Codes For Onkyo Components Connected Via Ri

    Resetting the REMOTE MODE Buttons For details on entering a remote control code for other components that are out of view, in a rack, for example. components, see “Entering Remote Control Codes” You can reset a REMOTE MODE button to its default (➔...
  • Page 71 A (Red) m RETURN B (Green) n AUDIO C (Yellow) o CLR The p supported by the AV receiver is the CEC system control function of the HDMI standard. D (Blue) g Number: 1 to 9, 0 Number: +10 En-71...
  • Page 72 Number: +10 Note ■ Cassette tape deck operation • With some components, certain buttons may not work as expected, and some may not work at all. Available buttons • See “Controlling Your iPod/iPhone” about the operation of e 1, t (Reverse...

  • Page 73: Appendix

    HDMI OUT MAIN. If your TV is ■ There’s no sound, or it’s very quiet If you have any trouble using the AV receiver, look for a connected to other video outputs, use the AV solution in this section. If you can’t resolve the issue receiver’s display when changing settings.
  • Page 74 Appendix If the input signal format is set to “PCM” or “DTS”. When Powered Zone 2 is used, playback in the main An audio cable may be picking up interference. Try — Set it to “Off”. room is reduced to 5.1channels and the front high and repositioning your cables.
  • Page 75 HDMI OUT MAIN. If your TV is connected to the HDMI output(s), select Make sure you’ve entered the correct remote control “- - - - -” in the “HDMI Input” setup to watch code. composite video, and component video sources.
  • Page 76 Music Server and Internet Radio Make sure the USB device is plugged in properly. — the Dock. If your iPod/iPhone is in a case, it may not ■ The AV receiver supports USB devices that support Can’t access the server or Internet radio connect properly to the Dock.
  • Page 77 In the following cases, the power consumption in These functions don’t work when Zone 2 is turned receiver’s display and release the buttons. standby mode may reach up to a maximum of 8.3 W: – The “HDMI Control(RIHD)” setting is set to ■...
  • Page 78 If the video source is connected to a composite video input, select the relevant input selector, and assign it to “- - - - -”. • To by-pass the upconversion, set the “Picture Mode” setting to “Direct” (➔ page 56).

  • Page 79: Firmware Update

    • If the USB device is partitioned, each section will be treated as an iPod/iPhone, USB or servers, etc. independent device. • If the USB device contains a lot of data, the AV receiver may take a while to read it. To be continued •...
  • Page 80 Please wait until it becomes operable. -10, The Ethernet cable was not detected. Select “Update via NET” and press ENTER. Reconnect the cable properly. Note that this option will not be available if there is no -11, -13, -21, Internet connection error.
  • Page 81 ONKAVR****_************.zip turning the AV receiver off and on again. • Never plug or unplug an HDMI cable or a USB device during the Unzip the downloaded file. The following three files update process. Do not turn off the AV receiver and do not remove the are created: •...
  • Page 82 Appendix Troubleshooting Case 1: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN If an error occurs, “Error!! *-**” is displayed on the AV http://www.onkyo.com/ receiver’s display. (Alpha-numeric characters on the front The Americas display are denoted by asterisks.) Refer to the following 18 Park Way, Upper Saddle River, N.J.

  • Page 83: Connection Tips And Video Signal Path

    • When composite video and component video sources are upconverted for HDMI OUT SUB, only signals with a resolution of 480i are output and the resolution remains the same. If your TV doesn’t support this resolution, there will be no picture (➔...
  • Page 84 ■ Signal Selection Audio Connection Formats If signals are present at more than one input, the inputs will be selected automatically in the following order of priority: Audio components can be connected by using any of the HDMI, component video, composite video.
  • Page 85 Appendix Video Resolution Chart The following tables show how video signals at different resolutions are output by the AV receiver. NTSC ✔: Output available Output HDMI Component Composite Input 1080p/24 1080p 1080i 720p 480p 480i 1080p 1080i 720p 480p 480i 480i ✔...

  • Page 86: Using An Rihd-Compatible Tv, Player, Or Recorder

    CEC (Consumer Electronics Control), which allows Players/Recorders • You can set on the menu screen of the TV to either output system control over HDMI and is part of the HDMI the audio from the speakers connected to the AV •...
  • Page 87 1. Turn on the power for all connected components. on the player models.) 2. Turn off the power of the TV, and confirm that the • Even if you set to output audio on the TV speakers, audio HDMI power of the connected components is turned off...

  • Page 88: About Hdmi

    PC are not supported. DSD and Multichannel PCM. • The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the picture is poor or there’s no sound from a component connected via HDMI, check its setup.

  • Page 89: Network/Usb Features

    62). network is recommended. Although it’s possible to play • The AV receiver does not support PPPoE settings, so if you have The following diagram shows how you can connect the AV music on a computer that’s connected to the network a PPPoE-type Internet connection, you must use a PPPoE- receiver to your home network.
  • Page 90 Storage” will be displayed. Modem: 28.8 kbps • The computer or media server must be on the same • If you connect a USB hard disk drive to the AV receiver’s USB Sound card: 16-bit sound card network as the AV receiver.
  • Page 91 For server playback and playback from a USB device, the The Digital Living Network Alliance is an international, • Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz, AV receiver supports the following music file formats. cross-industry collaboration. Members of DLNA develop a 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz,...

  • Page 92: License And Trademark Information

    Please note that the use of this accessory with iPod or iPhone may affect wireless performance. Manufactured under license from Dolby Laboratories. Dolby, Apple TV is a trademark of Apple Inc., registered in the U.S. and Pro Logic and the double-D symbol are trademarks of Dolby other countries.

  • Page 93: Specifications

    Maximum RCA Output Level and Impedance without notice. 2 V/2.2 kΩ (LINE OUT) Input IN 1, IN 2, IN 3, IN 4, IN 5, IN 6, IN 7, AUX Frequency Response 5 Hz - 100 kHz/+1 dB, –3 dB (DSP bypass) INPUT...
  • Page 94 Appendix Memo En-94...
  • Page 95 Appendix Memo En-95...
  • Page 96 The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700 Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong. Tel: 852-2429-3118 Fax: 852-2428-9039 http://www.onkyochina.com/ 1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai, China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396 http://www.cn.onkyo.com/...
  • Page 97 AV receiver. Using Last.fm Internet Radio ......5 Select the desired service and press ENTER. • Some of the services don’t allow the use of multiple user The top page of the selected service appears. accounts.

  • Page 98: Pandora ® Internet Radio -Getting Started (U.s. Only)

    Don’t play the song for a month: your account and stations you can return to your If you are tired of a song, you can put the song to sleep Onkyo receiver and press enter to begin listening to and Pandora will not play it for one month.

  • Page 99: Using Rhapsody (U.s. Only)

    Use q/w to select a channel, and press ENTER or Search: 1 to start playback. Use q/w to select “Sign in to your account” and then You can search for music by Artist, Album, or Track. Playback starts and the playback screen appears.

  • Page 100: Using The Siriusxm Internet Radio (North American Only)

    Setup. If you don’t know your username or password, www.sirius.com). Be sure to read this agreement before many days are left in your trial. After the trial period call Sirius XM at (888) 539-7474 for assistance. you purchase your subscription. Sirius, XM and all related expires, if you want to continue listening to the service, marks and logos are trademarks of Sirius XM Radio Inc.

  • Page 101: Using Last.fm Internet Radio

    Last.fm is a music service that learns what you love... Tracks”, “Library” and “Neighbours”. If you have the existing Last.fm account, you can sign Your new Onkyo AV receiver is very clever. If you have a Account Info: in to your account to select “Sign in to your free Last.fm account, it will keep track of all the songs...

  • Page 102: Using Slacker Personal Radio

    Using Internet Radio You can control the tracks with the buttons on the Using Slacker Personal Radio remote control. If you do not have an account, create one on the Enabled buttons: 1, 3, 2, 6 Slacker website (www.slacker.com) with your ■...

  • Page 103: Using Mp3Tunes

    Using Internet Radio Playing Contents on the AV Receiver Using MP3tunes Use q/w to select a track and press ENTER or 1 to start playback. Listen to your music collection on your home stereo in A playback screen appears. complete digital fidelity without a personal computer plus •...
  • Page 104 Remarque Utilisation de SiriusXM Internet Radio Les éléments de menu suivants s’affichent : • Les services disponibles peuvent varier en fonction de la région. (Amérique du Nord uniquement) .... 4 Add new user : Remove this user : Appuyez sur NET.

  • Page 105: Pandora ® Internet Radio -Pour Commencer (États-Unis Uniquement)

    à votre récepteur Onkyo et appuyez Si vous en avez assez d’une chanson, vous pouvez sur entrée pour écouter votre webradio Pandora mettre la chanson « au repos » et Pandora ne la lira PANDORA, le logo PANDORA, et l’habillage personnalisée.

  • Page 106: Utilisation De Rhapsody (Etats-Unis Uniquement)

    à la liste My Favorites. consultez « Utilisation de plusieurs comptes » (➔ page Conseil L’identification peut être réalisée à partir de l’écran « Users ». • Vous pouvez supprimer des pistes, des albums et des canaux Rhapsody marqués de My Library. Fr-3...

  • Page 107: Utilisation De Siriusxm Internet Radio (Amérique Du Nord Uniquement)

    Saisissez votre nom utilisateur et votre mot de passe (voir www.sirius.com). Assurez-vous de lire cet accord le nombre de jours restants dans votre essai. Une fois la dans l’écran clavier suivant ou dans Configuration avant d’acquérir votre abonnement. Sirius, XM et tous les période d’essai expirée, si vous souhaitez continuer à...

  • Page 108: Utilisation De La Webradio Last.fm

    Vous pouvez lire des pistes des tags les mieux évalués. Tag Radio : Personal Station : Funk polonaise ? Death pop ? Pensez à un style et nous Vous pouvez lire des pistes de votre station vous divertirons avec pendant des heures.

  • Page 109: Utilisation De Slacker Personal Radio

    Vous pouvez contrôlez les pistes avec les touches sur Utilisation de Slacker Personal Radio la télécommande. Si vous ne possédez pas de compte, créez-en un à Boutons activés : 1, 3, 2, 6 partir du site Web de Slacker (www.slacker.com) à...
  • Page 110 Uso de Rhapsody (sólo EE.UU.)....3 Pulse MENU cuando aparezca la pantalla de Nota usuarios. • Los servicios disponibles pueden variar de una región a otra. Aparecerán los siguientes elementos del menú: Uso de SiriusXM Internet Radio (solo Add new user: Norteamérica) ...........

  • Page 111: Pandora ® Internet Radio -Primeros Pasos (Solo Ee.uu.)

    Delete this station: Pandora ® Internet Radio Utilice q/w para seleccionar la emisora en la lista de emisoras y luego pulse ENTER. Esto eliminará de forma permanente una emisora de –Primeros pasos (solo EE.UU.) su cuenta de Pandora. Toda la información sobre sus Se inicia la reproducción y aparece la pantalla de...

  • Page 112: Uso De Rhapsody (Sólo Ee.uu.)

    Marca las emisoras de Rhapsody que se están reproduciendo actualmente. Add to My Favorites: Añade una canción, emisora o lista de reproducción a la lista Mis favoritos. Consejo • Puede eliminar las canciones, los álbumes y las emisoras de Rhapsody marcados de Mi biblioteca. Es-3...

  • Page 113: Uso De Siriusxm Internet Radio (Solo Norteamérica)

    Lea atentamente este acuerdo antes de aparece a continuación o en la configuración web. Si muestra los días que quedan de la prueba. Una vez que comprar la suscripción. Sirius, XM y todas las marcas y no sabe su nombre de usuario o la contraseña, llame a...

  • Page 114: Uso De Last.fm Internet Radio

    Utilice q/w para seleccionar “Sign in to your account”, y luego pulse ENTER. Puede reproducir pistas de “Recently Listened Last.fm es un servicio musical que sabe lo que le gusta... Tracks”, “Library” y “Neighbours”. Si ya tiene una cuenta de Last.fm, puede acceder a ella Su nuevo receptor de AV Onkyo es muy inteligente.

  • Page 115: Uso De Slacker Personal Radio

    Puede controlar las pistas con los botones del Uso de Slacker Personal Radio mando a distancia. Si no tiene una cuenta, cree una en el sitio web de Botones activados: 1, 3, 2, 6 Slacker (www.slacker.com) con su ordenador. ■...
  • Page 116 Y1203-2 SN 29401189B (C) Copyright 2012 Onkyo Sound & Vision Corporation Japan. All rights reserved. * 2 9 4 0 1 1 8 9 B *...
  • Page 117 If it flashes, verify that the Ethernet cable is firmly connected to the AV receiver. Select the desired service and press ENTER. • Some of the services don’t allow the use of multiple user The top page of the selected service appears. accounts.
  • Page 118 Last.fm is a music service that learns what you love... Tracks”, “Library” and “Neighbours”. If you have the existing Last.fm account, you can sign Your new Onkyo AV receiver is very clever. If you have a Account Info: in to your account to select “Sign in to your free Last.fm account, it will keep track of all the songs...
  • Page 119 Die oberste Seite des ausgewählten Services erscheint. Nutzerkonten zu. • Sie können bis zu 10 Nutzerkonten speichern. • Um zwischen den Konten umzuschalten, müssen Sie sich zuerst aus Ihrem aktuellen Konto ausloggen und sich dann wieder auf dem „Users“ Bildschirm einloggen.
  • Page 120 Sender wiedergeben („Your Library“, „Your Die aktuellen Nutzungspreise und umfassende Infos sind Neighbourhood“ und „Your Recommendations“). unter www.last.fm/subscribe erhältlich Y1112-1 SN 29401229 (C) Copyright 2012 Onkyo Sound & Vision Corporation Japan. All rights reserved. * 2 9 4 0 1 2 2 9 *...
  • Page 121 • Besides, it is not possible to add new codes to the existing remote controller presets. • Though the provided remote control codes are correct at the time of printing, they are subject to change by the manufacturer.
  • Page 122 • Cuando hay múltiples códigos relacionados con un fabricante, pruebe a introducirlos uno a uno • Quand il y a de multiples codes liés à un fabricant, essayez-les et entrez-les un par un jusqu’à ce hasta que coincida con su componente.
  • Page 123 “Remote Mode” e tasto “Display”. Beispiel „Remote Mode“ (Fernbedienungsmodus)-Taste und „Display“-Taste. Note: Hinweise: • I codici di controllo del telecomando non possono essere inseriti per [RECEIVER] e i tasti multi • Der Fernbedienungscode kann nicht [RECEIVER] und der Multi-Zonen-Taste zugeordnet werden. zona.
  • Page 124 Genom att ange en kod från fjärrkontrollkodlistan, kan du aktivera relevanta REMOTE MODE/Remote-indicator eenmaal traag knipperen. förvalda kanaler för den utrustningen. • När det finns flera olika koder för en tillverkare ska du försöka att ange dem en och en tills de Opmerkingen: stämmer överens med din utrustning.
  • Page 125 • [RECEIVER （接收机）] 和多区域按钮不能输入遥控编码。 • [RECEIER] （接收機）和多區域按鈕不能輸入遙控編碼。 • 只能为 [TV （电视）] 输入电视遥控编码。 • 您只能為 [TV] （電視）輸入電視遙控編碼。 • 除 [RECEIVER （接收机）]、[TV （电视）] 和多区域按钮外，不能为 REMOTE MODE （遥 • 除 [RECEIVER] （接收機） 、[TV] （電視）和多區域按鈕外，您可針對 REMOTE MODE 控模式）按钮指定任何类别的遥控编码。 但是，这些按钮仍可用作输入选择器按钮，因 （遙控模式）按鈕指定任何類別的遙控編碼。 但是，這些按鈕仍可用作為輸入選擇器按 此，选择与设备所要连接的输入端对应的 REMOTE MODE（遥控模式） 按钮。 例如，如果...
  • Page 126 Remote Control Codes Dedicated Onkyo Receiver Cable Set Top Box Cable Set Top Box Cable/PVR Combination Default 62503 mio TV 02802 Toshiba 01509 Samsung 01877 Zone 2 62506 Motorola 01376, 00858, 01562, 01582 Scientific Atlanta 01877, 01982 01982, 01998, 02378...
  • Page 127 70157 Zonda 70157 Technology Revox 40029 Onkyo 71817 Cairn 70157 CD-R Sansui 40029 Optimus 70000, 70032 California Audio Labs 70029, 70303 Denon 70626, 70766 Sony 40243 Panasonic 70029, 70303 Cambridge 70157 70072 Thorens 40029 Philips 70626, 70157 Cambridge Audio 70157...
  • Page 128 Remote Control Codes Accessory Satellite Set Top Box Satellite Set Top Box Satellite Set Top Box Polk Audio 82228 Amstrad 00847, 01175, 01662, 01413, 01567 Durabrand 01284 01693 Chess 01334, 01626 Echostar 00775, 00853, 01323, Ansonic 02418 01409, 02527 Video - Accessory...
  • Page 129 Remote Control Codes Satellite Set Top Box Satellite Set Top Box Satellite Set Top Box Satellite Set Top Box Hama 01567 Leiko 01626 Pace 00847, 00853, 00887, Sat Industrie 01611 01175, 01323, 01356, Hanseatic 01100 Lemon 01334 SAT+ 01409 01423, 01662, 01693,...
  • Page 130 Remote Control Codes Satellite Set Top Box Satellite Set Top Box SAT/PVR Combination SAT/PVR Combination Star 00887 00642 BskyB 01175, 01662 Schneider 01206 Stream System 01300 00879, 01356 Bush 01645 Sedea Electronique 01206 Strong 00853, 00879, 01284, United 01251, 01626, 02418...
  • Page 131 Remote Control Codes Television Television Television Television Akai 10178, 10556, 10037, Basic Line 10556, 10037, 10668, Casio 10037 Dick Smith 10698 10714, 10715, 10208, 11037 Electronics Cathay 10037 11675 Baur 10037, 10195, 10512 Digatron 10037 10037 Akiba 10037 Beaumark 10178...
  • Page 132 Remote Control Codes Television Television Television Television Erres 10037 Genesis 10037 Hisense 10556, 10508, 10208, 10037 11363, 12098 10171 Genexxa 10037 11709 Hitachi 10150, 10178, 10037, 10037 10171, 11864, 11886 Jinfeng 10208 10634, 11037, 10508, Euroman 10037 Godrej 11585 Jinxing...
  • Page 133 Remote Control Codes Television Television Television Television Lifetec 10037, 10714, 10668, Medion 10556, 10037, 10714, Naiko 10037 Onix 10698 11037, 12001 10668, 11037, 10698, Nakimura 10037 Onkyo 11807, 13100, 13500 10512, 11248, 11585, Linsar 11585 National 10508, 10208 11667, 11709...
  • Page 134 Remote Control Codes Television Television Television Television Phoenix 10037 Reflex 10037, 10668, 11037 Sei-Sinudyne 10037 SunBriteTV 11610 Phonola 10556, 10037 Relisys 11585 Serie Dorada 10178 Sungoo 11248 Pioneer 10037, 10698, 10512, Remotec 10171, 10037 Shanghai 10208 Sunny 10037 11457, 11636, 12171...
  • Page 135 Remote Control Codes Television Television Television Technosonic 10556, 10625, 10499, Toyoda 11709 11365, 12098 Humax 20739 11324 TRANS-continents 10556, 10037, 10668, Walker 11667 Panasonic 20614, 20616 Techvision 11709 11037 Waltham 10037, 10668, 11037 Philips 20739 Techwood 11037, 11667 Transonic 10037, 10698, 10512,...
  • Page 136 31354, 32056, 32084, Go Video 30741 32434, 32689 C-Tech 31152 Luxman 30573 GoldStar 30741 Pioneer 30571, 30142, 30631, California Audio Labs 30490 Luxor 30713 31571, 32442, 32860 Goodmans 30713, 31152 Cambridge Audio 32808 Magnavox 30503, 30539, 30646, Polk Audio 30539...
  • Page 137 Remote Control Codes Blu-ray Disc Radionette 30741 Sylvania 30630, 30675 Yamaha 30490, 30539, 30646, Sony 31516, 32180 30817, 31354, 32298, Radiotone 30713 Symphonic 30675 Sylvania 30675 32299 30522, 30571, 32213, Tamashi 31394 Toshiba 32551, 32705, 33157 Zenith 30503, 30741 32587...
  • Page 138 Remote Control Codes DVD-R TV/DVD Combination Victor 31597 Magnavox 12372 Yamaha 30646 Matsui 11037, 30713 Zenith 30741 Medion 12719 Nordmende 12001 HD-DVD Odys 12719 Integra 32901, 33104 33504 Panasonic 12170 30741 Philips 11454, 10556, 11394, 30539 Microsoft 32083 Powerpoint 10698...
  • Page 139 Remote Control Codes Memo...
  • Page 140 Y1112-1 SN 29401094 (C) Copyright 2012 ONKYO SOUND & VISION CORPORATION Japan. All rights reserved. * 2 9 4 0 1 0 9 4 *...

Table of Contents