Graco 17H572 Operation, Parts
  1. Manuals
  2. Brands
  3. Graco Manuals
  4. Paint Sprayer
  5. 17H572
  6. Operation, parts
Graco 17H572 Operation, Parts

Graco 17H572 Operation, Parts

Interior texture sprayers
Hide thumbs
Table of Contents

Advertisement

Quick Links

Operation, Parts
RTX1400 & RTX2000
Interior Texture Sprayers
For water-Based Materials Only.
Models: RTX1400si & RTX2000pi
70 psi (4.8 bar, 0.48 MPa) Maximum Working Pressure
Important Safety Instructions
Read all warnings and instructions in this manual and related manuals.
Be familiar with the controls and the proper usage of the equipment.
Save these instructions.
RTX1400si Gun – 311777
Use only genuine Graco replacement parts.
The use of non-Graco replacement parts may void warranty.
Related Manuals
RTX2000pi Gun – 3A3373
ti27336a
3A3258E
EN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 17H572 and is the answer not in the manual?

Questions and answers

Related Manuals for Graco 17H572

Summary of Contents for Graco 17H572

  • Page 1 Be familiar with the controls and the proper usage of the equipment. Save these instructions. Related Manuals RTX1400si Gun – 311777 RTX2000pi Gun – 3A3373 ti27336a Use only genuine Graco replacement parts. The use of non-Graco replacement parts may void warranty.

  • Page 2: Table Of Contents

    Graco Standard Warranty ........

  • Page 3: Models

    Models Models Model RTX1400si 17H572 RTX1400si RentalHD 17P189 RTX2000pi 17H573 110474 RTX2000pi Rental 17H574 Certified to RTX2000pi RentalHD 17K301 CAN/CSA C22.2 No. 68 Conforms to UL 1450 3A3258E...

  • Page 4: Warnings

    Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings.
  • Page 5 Do not kink or over-bend the material or air hoses. • Do not expose the hose to temperatures or to pressures in excess of those specified by Graco. • Do not use the hose as a strength member to pull or lift the equipment.
  • Page 6 Warnings PRESSURIZED EQUIPMENT HAZARD Fluid from the equipment, leaks, or ruptured components can splash in the eyes or on skin and cause serious injury. • Follow the Pressure Relief Procedure when you stop spraying/dispensing and before cleaning, checking, or servicing equipment. •...

  • Page 7: Component Identification

    Component Identification Component Identification RTX1400si ti27337a ON/OFF Switch Handle Material Hopper Toolbox Burp Guard Power Cord Material/Air Hose Pump Access Panel Material Thickness Gauge RotoFlex™ II Pump Nozzle Pump Hose Outlet Air Hose Outlet Air control valve Material Flow Gauge Model/Serial Tag (Not shown, located Material Flow Control on bottom of unit.)

  • Page 8: Rtx2000Pi

    Component Identification RTX2000pi ti27338a Material Hopper Handle Burp Guard Toolbox Material/Air Hose Power Cord Material Thickness Gauge Pump Access Panel Nozzle & retaining ring RotoFlex™ II Pump Pump Hose Outlet Prime Valve Air Hose Outlet Air control valve Material Flow Gauge Model/Serial Tag (Not shown, located Material Flow Control on bottom of unit.)

  • Page 9: Preparation

    Preparation Preparation Pressure Relief Procedure Open air control valve. Follow the Pressure Relief Procedure whenever you see this symbol. This equipment stays pressurized until ti27341a pressure is manually relieved. To help prevent serious injury from pressurized On the RTX2000pi, open gun prime fluid or splashed fluid follow the Pressure valve.

  • Page 10: Auxiliary Air Compressor

    Preparation • NOTE: Lighter gauge or longer extension “Soft” refers to the function where the cords may reduce sprayer performance. sprayer slowly starts the pump. This prevents a large “splotch” of material Auxiliary Air Compressor from being discharged from the gun when trigger is pulled after the sprayer Do not use an auxiliary air compressor with has sat idle for a period of time.

  • Page 11: Setup

    Setup Setup Connect material hose to gun. NOTICE • Do not store sprayer under pressure. ti27344a • Do not allow material to dry inside pump, hoses, gun or spray system. Make sure burp guard is installed. • When operating a RTX1400SI and you are going to stop spraying for more than five minutes turn sprayer OFF to prevent shortened pump life.
  • Page 12 Setup Pour one gallon (four liters) of water into 10. Point gun into waste bucket and pull the material hopper. trigger to pump water through the system. Continue to trigger gun until material hopper is empty. NOTICE To prevent pump damage, before adding material or starting unit in cold weather, run warm water through the pump.

  • Page 13: Mixing Material

    Mixing Material Mixing Material Premix Slowly add approximately 2 to 4 quarts (1.9 to 3.8 liters) of water to a 5 gallon (18.9 liter) bucket of premix. NOTE: Correct material mixture is essential. The pump will not operate if the mixture is too thick.
  • Page 14 Mixing Material NOTE: For an accurate test, be sure gauge is If the ball does not sink completely into completely dry and clean every time it is the mixture within 10 seconds, add more used. water, agitate and try test again. Observe the ball on the material.

  • Page 15: Operation

    Operation Operation Texture Spraying Recommended Nozzle Selection Charts RTX1400si Application Nozzle Size Air Volume Application Nozzle Size Air Volume 6 mm, white 6 mm, white Simulated medium to high Splatter coat low to medium (fine to medium) 8 mm, gray Acoustic 8 mm, gray (coarse)
  • Page 16 Operation • To achieve uniform spray pattern, adjust air When you first start to spray, hold the valve and flow adjustment nut on gun. If you gun away from the surface and gradually do not achieve the desired pattern, change work your way closer to it.

  • Page 17: Shutdown And Cleanup

    Shutdown and Cleanup Shutdown and Cleanup NOTE: Keep pump and hose clean when switching between simulated acoustic, knockdown and orange peel applications. A dirty pump can release particles of texture into the finish. ti27383a • To increase pump life, life turn power OFF when not spraying.

  • Page 18: Clean Material Hopper

    Shutdown and Cleanup Spray inside material hopper to circulate water through gun and hose. While circulating water, use gun to clean material hopper. ti27340a 10. Open gun air valve. Perform pressure relief procedure, Pressure Relief Procedure, page 9. Partially open gun air valve to use air to Air hose fittings can get hot.

  • Page 19: Transporting Sprayer

    Shutdown and Cleanup Plug opening on bottom of material hopper with your hand. NOTICE Water or material remaining in unit when temperatures are below freezing can damage motor and/or delay pump startup. Do not allow unit to freeze. To ensure water and material are com- pletely drained out of unit: Remove material hose from sprayer.

  • Page 20: Maintenance

    Maintenance Maintenance Routine maintenance is important to ensure proper operation of your sprayer. Maintenance includes performing routine actions which keep your sprayer in operation and prevent trouble in the future. Activity Interval Inspect motor shield vents for blockage. Daily or each time you spray Check sprayer stall (RTX2000pi only).

  • Page 21: Troubleshooting

    Troubleshooting Troubleshooting Follow Pressure Relief Procedure, Check all possible problems and causes page 9, before checking or repairing. before disassembling the unit. Problem Cause Solution Sprayer won’t run Power switch not on Turn switch on. No power at wall outlet Check outlet by plugging in another appliance.
  • Page 22 Grounding and Electrical Requirements, page 9. Gun needle plugged Clean needle and retry. Worn compressor Replace compressor. Contact a qualified Graco Service Cen- ter. Lines not connected Check all quick disconnect connections to gun and hoses. Damaged hose. Replace hose.
  • Page 23 Motor or control is damaged. Take sprayer to Graco cycle. authorized service center. Electric outlet is not providing Try a different outlet or plug in power.
  • Page 24 Troubleshooting Problem Cause Solution Sprayer cycles ON and OFF Pressure switch is damaged. Replace pressure switch. when trigger is released. Compressed air system leak. Locate leak; check gun, twin line hose, or internal system. Reseal leaky fitting or replace Sprayer cycles ON and OFF hose.

  • Page 25: Rtx1400Si Sprayer

    RTX1400si Sprayer RTX1400si Sprayer Ref. Torque Ref. Torque 15-20 in-lb (1.7 - 2.3 N•m) 27-32 in-lb (3.1 - 3.6 N•m) 75-95 in-lb (8.5 - 10.7 N•m) 90-110 in-lb (10.2 - 12.4 N•m) 65-85 in-lb (7.3 - 9.6 N•m) then 50-70 in-lb (5.6 - 7.9 N•m) back off 1/4 turn 40-50 in-lb (4.5 - 5.6 N•m) See page 32.
  • Page 26 RTX1400si Sprayer RTX1400si Sprayer (cont’d) Ref. Torque Ref. Torque 15-20 in-lb (1.7 - 2.3 N•m) 27-32 in-lb (3.1 - 3.6 N•m) 75-95 in-lb (8.5 - 10.7 N•m) 90-110 in-lb (10.2 - 12.4 N•m) 65-85 in-lb (7.3 - 9.6 N•m) then 50-70 in-lb (5.6 - 7.9 N•m) back off 1/4 turn 40-50 in-lb (4.5 - 5.7 N•m)

  • Page 27: Rtx1400Si Sprayer Parts List

    RTX1400si Sprayer RTX1400si Sprayer Parts List Ref. Part Description Qty. Ref. Part Description Qty.  15H841 LABEL, warning 17H407 FRAME, front  15K616 LABEL, caution 15J600 BOX, tool 17J928 LABEL, instructions 15H069 SUPPORT, hopper  TUBE, air, 0.250 17H404 FRAME, back ...

  • Page 28: Rtx2000Pi Sprayer

    RTX2000pi Sprayer RTX2000pi Sprayer Ref. Torque Ref. Torque 15-20 in-lb (1.7 - 2.3 N•m) 27-32 in-lb (3.1 - 3.6 N•m) 75-95 in-lb (8.5 - 10.7 N•m) 90-110 in-lb (10.2 - 12.4 N•m) 65-85 in-lb (7.3 - 9.6 N•m) then 50-70 in-lb (5.6 - 7.9 N•m) back off 1/4 turn 40-50 in-lb (4.5 - 5.7 N•m) See page 32.
  • Page 29 RTX2000pi Sprayer (cont’d) RTX2000pi Sprayer Ref. Torque Ref. Torque 15-20 in-lb (1.7 - 2.3 N•m) 90-110 in-lb (10.2 - 12.4 N•m) 75-95 in-lb (8.5 - 10.7 N•m) 9-11 in-lb (1- 1.2 N•m) 65-85 in-lb (7.3 - 9.6 N•m) then 50-70 in-lb (5.6 - 7.9 N•m) back off 1/4 turn 40-50 in-lb (4.5 - 5.7 N•m) 120-130 in-lb (13.6 - 14.7 N•m)

  • Page 30: Rtx2000Pi Sprayer Parts List

    RTX2000pi Sprayer RTX2000pi Sprayer Parts List Ref. Part Description Qty. Ref. Part Description Qty. 120830 CLAMP, loop 17H407 FRAME, front  16M768 LABEL, warning 15J600 BOX, tool 121141 FITTING, elbow, swivel 15H069 SUPPORT, hopper 17H638 BAFFLE, hopper 17H404 FRAME, back 17K597 KIT, repair, solenoid valve 17K497 SHIELD, right includes 81...
  • Page 31 RTX2000pi Sprayer Ref. Part Description Qty. 105 110198 COUPLER, line, air 106 17J393 FITTING, tube, straight 107 111800 SCREW, cap hex, hd 108 110996 NUT, hex, flange head 109  TUBE, air, 0.375 118 102478 STRAP, tie 119  TUBE, air 121 17L028 LABEL, pi models 122 17L120 GROMMET, edge 123 17L386 FITTING...

  • Page 32: Compressor Parts

    Compressor Parts Compressor Parts Ref. Torque Ref. Torque 18-22 ft-lb (24.4 - 29.8 N•m) 50-65 in-lb (5.7 - 7.3 N•m) 120-140 in-lb (13.6 - 15.8 N•m) Finger tighten 190-230 in-lb (21.5 - 26 N•m) cap screw in position 4 first then torque cap screws in the sequence illustrated.

  • Page 33: Compressor Parts List

    Compressor Parts Compressor Parts List Part Description Ref. Qty. Part Description Ref. Qty. 24S133 KIT, repair, cooler 24S129 KIT, repair, compressor, includes 27 rebuild includes 4, 5, 6, 7, 24S128 KIT, repair, compressor, 14, 17, 20, 26, 28, 29, 30, complete 120234 BELT, 3mm, timing...

  • Page 34: Gun & Hose

    Gun & Hose Gun & Hose RTX1400si ti31640a Part Description Ref. Qty. 288629 GUN, spray, texture 15B171 NOZZLE, black, 12mm, #3 15D525 NOZZLE, beige, 4mm 17J454 HOSE, texture, blue 15C090 GAUGE, thickness, fluid RTX2000pi ti31641a Part Description Ref. Qty. 24S134 GUN, spray, texture 17J420 HOSE, texture, 2line...

  • Page 35: Wiring Diagram

    Wiring Diagram Wiring Diagram RTX1400si POWER CORD GREEN WHITE MOTOR BLACK SWITCH HOUR METER ti27930b Hour meter on 17P189 models only. RTX2000pi YELLOW MOTOR GRAY ORANGE 49 REF ORANGE TRIAC VIOLET GATE BROWN WHITE GRAY ORANGE ORANGE ORANGE PRIME PRESSURE FLOW TRIAC MOTOR...

  • Page 36: Technical Specifications

    Technical Specifications Technical Specifications Metric Sprayer Material Hopper Capacity RTX1400si 10 gal 38 l RTX2000pi 13 gal 49 l Maximum Delivery with Texture RTX1400si 1.4 gpm 5.3 lpm RTX2000pi 2.0 gpm 7.6 lpm Maximum Fluid Working Pressure 70 psi 4.8 bar, 0.48 MPa Maximum Air Working Pressure 45 psi 3.1 bar, 0.31 MPa...
  • Page 37 Technical Specifications Metric Materials of Construction Wetted materials on all models brass, aluminum, plastic, stainless steel, plated carbon steel, elastomer Notes * Startup pressures and displacement per cycle may vary based on suction condition, discharge head, air pressure, and fluid type. ** Sound pressure measured 3 feet (1 meter) from equipment while spraying.

  • Page 38: Graco Standard Warranty

    Graco’s written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts.

  • Page 39: Graco Information

    Graco Information Graco Information For the latest information about Graco products, visit www.graco.com. For patent information, see www.graco.com/patents. TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor. 3A3258E...
  • Page 40 Original instructions. This manual contains English. MM 3A3258 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA Copyright 2015, Graco Inc. All Graco manufacturing locations are registered to ISO 9001. www.graco.com...

Table of Contents