Related Manuals for Graco 17G180
Summary of Contents for Graco 17G180
- Page 1 User Manual of Product 1: Graco 17G180 Magnum ProX19 Cart Paint Sprayer, Blue & white...
-
Page 2: Important Safety Instructions
Save these instructions. 888-541-9788 Magnum Products Operational Videos http://magnum.graco.com/magop/ http://magnum.graco.com/magop/ For portable spray applications of architectural paints and coatings only. Not approved for use in explosive atmospheres or hazardous locations. -
Page 3: Before You Spray
Model Stand (Series) Cart (Series) 17G177 (A) 17G178 (A) ProX17 17K438 (A) CAN178 (A) CAN177 (A) ProLTS170 17H198 (A) 17G180 (A) 17G179 (A) 110474 ProX19 17K439 (A) CAN179 (A) Certified to CAN180 (A) CAN/CSA ProLTS190 17H206 (A) C22.2 No. 68... -
Page 4: Table Of Contents
Contents Contents Before You Spray ............2 Warnings . - Page 5 Graco Standard Warranty ........
- Page 6 Notes Notes 3A6419B EN...
-
Page 7: Warnings
Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. - Page 8 Use Graco conductive or grounded high-pressure airless paint sprayer hoses.
- Page 9 Check hoses and parts for signs of damage. Replace any damaged hoses or parts. • This system is capable of producing 3000 psi (207 bar, 20.7 MPa). Use Graco replacement parts or accessories that are rated a minimum of 3000 psi (207 bar, 20.7 MPa).
- Page 10 Warnings PRESSURIZED ALUMINUM PARTS HAZARD Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemical reaction and equipment rupture. Failure to follow this warning can result in death, serious injury, or property damage. • Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents.
-
Page 11: Know Your Sprayer
Know Your Sprayer Know Your Sprayer ProX and ProLTS Stand Models Airless Hose Connection Power - ON/OFF Switch Airless Hose Pressure Control Knob InstaClean™ Filter (inside fluid outlet) Prime/Spray Valve Inlet Screen Spray Tip Power Cord PushPrime™ Button Easy Access Door Suction Tube W Suction Tube Drip Cup Drain Tube (with diffuser) -
Page 12: Know Your Sprayer
Know Your Sprayer Know Your Sprayer ProX and ProLTS Cart Models Airless Hose Connection Power - ON/OFF Switch Airless Hose Pressure Control Knob InstaClean Filter (inside fluid outlet) Prime/Spray Valve Pail Hanger Spray Tip Inlet Screen PushPrime Button Power Cord Suction Tube Easy Access Door Drain Tube (with diffuser) -
Page 13: Know Your Controls
Know Your Controls Know Your Controls The ON/OFF power switch controls the main power to your sprayer. The Pressure Control knob increases or decreases the pressure and flow of the paint. The Prime/Spray Valve directs the fluid to either the Drain Tube or the hose and gun. It is used to prime the sprayer, which means to evacuate the air out of the pump, hose, and gun. -
Page 14: Set Up
Set Up Set Up Assemble Your Sprayer Assure Spray Tip is properly inserted into the Spray Tip Guard, and the Spray Connect airless hose to airless hose Tip Guard assembly is tightened connection (P) on sprayer. Use wrench securely to gun. See Spray Tip to tighten securely. -
Page 15: Start Up
Start Up Start Up Pressure Relief Procedure Turn pressure control knob to lowest setting. Follow the Pressure Relief Procedure whenever you see this symbol. This equipment stays pressurized until Put Drain Tube into a waste pail and pressure is manually relieved. To help turn Prime/Spray Valve down to PRIME prevent serious injury from pressurized position to relieve pressure. -
Page 16: Flush Storage Fluid
Start Up Flush Storage Fluid Align setting indicator with the START setting on the pressure control knob. It is important that you flush storage fluid from the sprayer before using it. Make certain ON/OFF switch is OFF. Separate Drain Tube (smaller) from Suction Tube (larger). -
Page 17: Strain The Paint
Start Up Strain the Paint Turn ON/OFF switch to ON position. Wait to see paint coming out of Drain Disposable paint strainer bags are used to Tube. remove coarse particles and debris from Turn ON/OFF switch to OFF position. new or previously opened paint or stain, and are available where paint is sold. -
Page 18: Refilling Paint Pail
Start Up Release trigger. Engage trigger lock. Refilling Paint Pail When the paint pail runs low and the gun stops spraying, refill the paint pail and repeat the Fill Pump (Prime Pump) procedure, then the Fill Gun and Hose procedure. You are now ready to spray! NOTE: It is normal for the motor to stop once the sprayer is primed and under pressure. -
Page 19: Spraying
Spraying Spraying Start Turn pressure control knob to START Disengage trigger lock. position. Adjust Pressure Control To select a setting, align symbol on pressure control knob with setting indicator on sprayer. For best spray results with lowest overspray, adjust pressure control to “START” setting. Test the spray pattern on a test area or piece of cardboard. -
Page 20: Spray Techniques
Spraying Spray Techniques Use a piece of scrap cardboard to practice these basic spraying techniques before you begin spraying the surface. • Hold gun 12 in. (30 cm) from surface and aim straight at surface. Tilting gun to direct spray angle causes an uneven finish. -
Page 21: Spray Tip And Pressure Selection
Spraying Spray Tip and Pressure Selection Spray Tips come in a variety of sizes for spraying a wide range of materials. Your sprayer includes a 515 Spray Tip for use with most paints on large surfaces such as walls and ceilings. If you are spraying stain or need a different spray fan width, refer to the Spray Tip chart below to select the best Spray Tip for your project. -
Page 22: Clear Spray Tip Clog
Spraying Clear Spray Tip Clog Engage trigger lock. Rotate Spray Tip back to SPRAY position. Disengage trigger lock and continue spraying. SPRAY In the event that particles or debris clog the Spray Tip, the Spray Tip can be reversed to quickly and easily clear particles without disassembling the sprayer. - Page 23 Spraying Use Spray Tip to align gasket and Turn the arrow shaped handle on the Spray Tip forward to the SPRAY seal in the Spray Tip Guard. position. Screw Spray Tip Guard assembly onto the gun and tighten. Spray Tip must be pushed all the way into the Spray Tip Guard.
-
Page 24: Cleanup
Cleanup Cleanup Cleaning the sprayer after each use results in Separate Drain Tube (smaller) from a trouble free start up the next time the Suction Tube (larger). sprayer is used. ti27 7 124a • For short term shutdown periods (over- Place empty waste and flushing fluid night to two days), refer to Short Term pails side by side. - Page 25 Cleanup Continue to hold gun trigger until Turn Prime/Spray valve down to you see paint diluted with flushing PRIME position. fluid starting to come out of gun. 13. While continuing to trigger gun, quickly move gun to redirect spray into waste pail.
-
Page 26: Cleanup With Power Flush Valve
Cleanup Cleanup with Power Flush Screw Power Flush Valve (included with sprayer) to garden hose. Close Valve Power Flush Valve. (Water-based materials only) Turn on water. Open Power Flush Valve. Rinse paint off Suction Tube, Power flushing is a faster method of cleanup. Drain Tube and inlet screen. - Page 27 Cleanup Turn Prime/Spray Valve horizontal 16. Turn pressure control knob to the low- to SPRAY position (C). est setting. Turn ON/OFF switch to ON position 17. Stop triggering gun. Engage the trigger (D). lock. Continue to hold gun trigger until you see paint diluted with flushing fluid starting to come out of gun.
-
Page 28: Cleaning Instaclean Filter
Cleanup Cleaning InstaClean Filter Clean the Gun and Gun Filter The InstaClean Filter prevents debris from entering paint hose. After each use, remove Perform Pressure Relief Procedure, and clean it to ensure peak performance. page 14. Perform Pressure Relief Procedure, Remove the gun handle by unscrewing page 14. -
Page 29: Storage
Storage Storage With proper storage, the sprayer will be ready Engage trigger lock. to use the next time it is needed. ti25196b Leave gun attached to hose. Remove Spray Tip and Spray Tip Guard and clean with water or flushing Short Term Storage fluid and a brush. - Page 30 Storage Place drain tube in waste pail. Turn Screw Inlet Screen back to Suction pressure control to the START position. Tube. Ensure that spray gun and hose stay attached to sprayer. ProX21 only: Turn Spray/Prime Valve horizontal to Place Suction Tube in Pump Armor SPRAY position for storage.
-
Page 31: Reference
Reference Reference Static Grounding Instructions (Oil or Solvent-Based Lacquer Conversion Kit Flammable Materials) To spray lacquers and other solvent-based flammable materials with models other than ProX21, you must purchase a lacquer conversion kit and follow Static Grounding The equipment must be grounded to Instructions (Oil or Solvent-Based reduce the risk of static sparking. -
Page 32: Quick Reference
Reference Quick Reference Page Name Description Power - ON/OFF Switch Turns sprayer ON and OFF. Pressure Control Knob Increases (clockwise) and decreases (counter-clockwise) fluid pressure in pump, hose, and spray gun. To select function, align symbol on pressure control knob with setting indicator. •... -
Page 33: Maintenance
Maintenance Maintenance Routine maintenance is important to ensure proper operation of your sprayer. Storage/Priming Tool Maintenance Activity Inspect motor shroud openings for Perform these steps if you are experiencing blockage every time you spray. difficulty priming your sprayer. Clean/inspect inlet screen, InstaClean filter, and gun filter every time you spray. -
Page 34: Inlet Valve Removal
Maintenance Inlet Valve Removal Squeeze Pump Armor bottle until Pump Armor flows into the Drain Tube. An integrated tool is included in the frame to remove the inlet valve assembly from the pump. If you suspect that the inlet valve is clogged or stuck, remove the valve assembly and clean or replace. -
Page 35: Pump Repair
See ProXChange Pump Parts Slide pump assembly off the mounting List, page 49, or consult a Graco/MAGNUM pins. authorized retailer, distributor, or service center. Each time the pump kit is replaced, check pump inlet and outlet valves for wear or damage. -
Page 36: Pump Installation
Maintenance ProXChange Removal Tool Move pump rod up or down until cap is level with the opening in the An integrated tool is included in the frame to yoke. remove the ProXChange packing assembly. See ProXChange Pump manual for complete repair instructions. ti27037a Push on pump rod to slide pump assembly back on to mounting... -
Page 37: Troubleshooting
If not frozen, check for hardened paint in pump. If paint has hardened in pump. See Pump Repair, page 34. If motor does not turn with pump removed, consult a Graco/ Magnum authorized retailer, distributor, or service center. Motor or control is damaged. - Page 38 Inspect Suction Tube connection for cracks or vacuum leaks. Debris in paint causing obstruction. Strain the paint. See Strain the Paint, page 16. Prime/Spray Valve is worn or Take sprayer to Graco/MAGNUM obstructed with debris. authorized service center. 3A6419B EN...
- Page 39 Troubleshooting Problem Cause Solution Pump is primed, but can not achieve Spray Tip may be partially clogged. See Clear Spray Tip Clog, page 21. good spray pattern. Reversible Spray Tip is in UNCLOG Rotate arrow-shaped handle on position. Spray Tip so it points forward to SPRAY position.
-
Page 40: Online Resources
Choose Spray Tip with narrower fan. Make sure gun is close enough to surface. Fan pattern varies dramatically while Pressure control switch is worn and Take sprayer to Graco/M AGNUM spraying. causing excessive pressure variation. authorized service center. Cannot trigger spray gun. -
Page 41: Prox17, Prox19, Prolts170 Stand Sprayer Parts
ProX17, ProX19, ProLTS170 Stand Sprayer ProX17, ProX19, ProLTS170 Stand Sprayer Parts Ref. Torque 140-160 in-lb (16-18 N•m) 30-35 in-lb (3.5-4.0 N•m) 110-120 in-lb (12-14 N•m) 45-55 in-lb (5-6 N•m) See page 48. 3A6419B EN... -
Page 42: Prox17, Prox19, Prolts170 Stand Sprayer Parts List
ProX17, ProX19, ProLTS170 Stand Sprayer ProX17, ProX19, ProLTS170 Stand Sprayer Parts List Ref. Part Description Qty. Ref. Part Description Qty. 17J033 ProX19 17F756 KIT, repair, motor, 17J032 ProLTS170 120V includes 1a, 22 247340 HOSE, cpld, 287770 1/4 in. x 50 ft 17J863 KIT, gear and yoke GUN, spray, SG3... -
Page 43: Prox21 Stand Sprayer Parts
ProX21 Stand Sprayer Parts ProX21 Stand Sprayer Parts Ref. Torque 140-160 in-lb (16-18 N•m) 30-35 in-lb (3.5-4.0 N•m) 110-120 in-lb (12-14 N•m) See page 3A6419B EN... -
Page 44: Prox21 Stand Sprayer Parts List
ProX21 Stand Sprayer Parts ProX21 Stand Sprayer Parts List Part Description Ref. Qty. Part Description Ref. Qty. 116139 GRIP, handle MOTOR, 120V includes 17J035 LABEL, front, ProX21 1a, 22 247340 HOSE, cpld, 17K684 Series A 1/4 in. x 50 ft 17F757 Series B 243012... -
Page 45: Prox17, Prox19, Prolts190 Cart Sprayer Parts
ProX17, ProX19, ProLTS190 Cart Sprayer ProX17, ProX19, ProLTS190 Cart Sprayer Parts Ref. Torque 30-35 in-lb (3.5-4.0 N•m) 110-120 in-lb (12-14 N•m) 45-55 in-lb (5-6 N•m) See page 48. 3A6419B EN... -
Page 46: Prox17, Prox19, Prolts190 Cart Sprayer Parts List
ProX17, ProX19, ProLTS190 Cart Sprayer Parts List Part Description Ref. Qty. Part Description Ref. Qty. 243012 Models 17G178, 17F756 MOTOR, 120V 17G180, 17H206 includes1a, 22 246506 Model 17K439 287770 112612 CAP, hub 17J863 KIT, gear and yoke WHEEL includes 34 17J173 CORD, power 24Y324... -
Page 47: Prox21 Cart Sprayer Parts
ProX21 Cart Sprayer Parts ProX21 Cart Sprayer Parts Ref. Torque 30-35 in-lb (3.5-4.0 N•m) 110-120 in-lb (12 -14 N•m) See page 48. 3A6419B EN... -
Page 48: Prox21 Cart Sprayer Parts List
ProX21 Cart Sprayer Parts ProX21 Cart Sprayer Parts List Part Description Ref. Qty. Part Description Ref. Qty. 247340 HOSE, cpld, KIT, repair, motor, 120V 1/4 in. x 50 ft includes 1a, 22 243012 GUN, spray,SG3 17K684 Series A 119452 CAP, hub 17F757 Series B 119451... -
Page 49: Proxchange Pump Parts
ProXChange Pump Parts ProXChange Pump Parts Ref. Torque 140-160 in-lb (16-18 N•m) 30-35 in-lb (3.4-4.0 N•m) 30-35 ft-lb (40-48 N•m) 220-250 in-lb (25-28 N•m) 320-380 in-lb (36-43 N•m) ti27261a ti27261 3A6419B EN... -
Page 50: Proxchange Pump Parts List
ProXChange Pump Parts ProXChange Pump Parts List Part Description Ref. Qty. Part Description Ref. Qty. 120776 PACKING, O-ring 17G447 HOUSING, pump 24Y327 KIT, repair outlet 17D364 GUIDE, ball includes 12,13 128336 SPRING, compression 17J880 KIT, outlet valve repair 105445 BALL, 0.5 in. includes 42 117501 SCREW, mach, slot... -
Page 51: Wiring Diagram - 110/120V
Wiring Diagram - 110/120V Wiring Diagram - 110/120V ti27233a 3A6419B EN... - Page 52 Notes Notes 3A6419B EN...
-
Page 53: Technical Specifications
Technical Specifications Technical Specifications Metric Sprayer Maximum fluid working pressure 3000 psi 207 bar, 20.7 MPa Maximum Delivery ProX17, ProLTS170 0.34 gpm 1.3 lpm ProX19, ProLTS190 0.38 gpm 1.4 lpm ProX21 0.47 gpm 1.8 lpm Maximum Spray Tip Size ProX17, ProLTS170 0.017 in. - Page 54 Technical Specifications Metric ProX21 Stand 25.0 lb. 11.3 kg ProX17 Cart 37.5 lb. 17.0 kg ProX19, ProLTS190 Cart 41.2 lb. 18.7 kg ProX21 Cart 49.5 lb. 22.5 kg Storage temperature range –30° to 160°F –35° to 71°C Operating temperature range 40°...
-
Page 55: Graco Standard Warranty
Graco’s written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. -
Page 56: Graco Information
Graco Information Graco Information For the latest information about Graco products, visit www.graco.com. For patent information, see www.graco.com/patents. TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor. 3A6419B EN... - Page 57 Original instructions. This manual contains English. MM 3A6419 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA Copyright 2018, Graco Inc. All Graco manufacturing locations are registered to ISO 9001. www.graco.com...
Need help?
Do you have a question about the 17G180 and is the answer not in the manual?
Questions and answers