Table of Contents
Advertisement
WI818D 8/00
EASY MENU DRIVEN PROGRAM MODE
DEALER PROGRAM - PRELIMINARY INFORMATION
!
Only Keypad #1 may be used for both dealer and user programming, however this keypad may be located in any
area.
!
The Master Security Code is printed on the panel's microprocessor can. Use this code to enter the Dealer Program
Mode to program a custom Dealer Security Code. Record the number, then remove the code label to prevent
unauthorized access to the panel. If you forget your Dealer Security Code, use the Master Security Code to enter
programming.
!
After entering codes or data, press the save
!
If the keypad is in the Program Mode and no activity is detected for longer than 4 minutes, a steady tone will sound.
Silence the sounder by pressing the
!
A panel that has been COLD STARTED (Address Location 4093) performs identically to a new panel.
!
When programming more than 2 areas, Direct Address Programming Mode must be used to complete the program.
KEYPAD #1: For ease of programming, it is recommended that a GEM-RP1CAe2 (Version 6) be used as Keypad #1.
(Regardless of which keypad is selected, all new keypads are configured as Keypad #1 out of the box.)
If a GEM-RP2ASe2 (Version 5b) is used, configure address jumpers as Keypad #1 (see Configuring the GEM-RP2ASe2
Keypad.).
ACCESSING DEALER PROGRAM MODE
1. Press EEEEEE A
2. Press g Until "ACTIVATE PROGRAM Y/N" (GEM-RP1CAe2),
"TURNON PROG Y/N" (GEM-RP2ASe2) or "17" (GEM-RP3DGTL) appears on the keypad display.
3. Press F To Enter Dealer Program Mode.
4. Press CC To Exit Dealer Program Mode when finished.
CUSTOMIZING A DEFAULT PROGRAM
For any new panel, you can design a default program that will best suit your application. Using this procedure, you will configure the panel for:
!
Number of Zones in Area 1
!
Number of Zones in Area 2
!
Fire Zones
!
2-Wire Fire Zones
!
Local System or Central Station Reporting
!
Exit/Entry Zones
!
Interior Zones
!
Number of Keypads in Area 1
This procedure will automatically set up system keypads, EZMs, wireless transmitters, etc. After your basic default program has been loaded, you
may alter it as necessary in the Direct Address Program Mode.
NEW PANELS: The custom default program may be created for new panels only. Once the panel has been programmed by any
means, the number of areas, number of zones, fire zones, entry/exit zones and interior zones will be suppressed and cannot be
changed. Should it be necessary to create a new custom default program, (a) from the Dealer Program Mode, press the
to enter the Direct Address Program Mode; (b) access Location 4091 (Clear Program); (c) press the J button and start over.
L
NAPCO Security Systems
J
button. Data will not be stored into memory unless it is pressed.
button to continue, or by pressing the
G
Master Security Code
(on microshield)
!
Number of Keypads in Area 2
!
CS Receiver 1 Telephone Number
!
Auto Download ID Number & PC Preset
Callback Telephone Number
!
CS Receiver 1 Account Number
!
CS Receiver 1 Format
!
User Codes
!
RF Transmitter Points
button to exit.
C
!
Key Fob Transmitters
!
Zone Descriptions *
!
Date *
!
Time *
!
Dealer Code
* NOTE: GEM-RP1CAe2 Keypad Only
X
GEM-P3200 Programming Instructions
!
Page 5
GEMINI
SYSTEM ARMED
AI #ZN=08 #KP=1
# OF ZONES IN AREA 1
A2 #ZN=00 #KP=0
01/01/97 12:00AM
ENTER # ZONES X X
NEXT/YES
A
1 2
3
E
D
PRIOR/NO
B
4
5 6
F
AREA
C
7 8 9 0
G
COMPUTERIZED SECURITY SYSTEM
R
GEM-P3200
GEM-P3200
CONTROL
R
COMMUNCIATOR
MASTER SECURITY CODE
# - # - # - # - # - #
button
C
Advertisement
Table of Contents
