Advertisement
CONNECTIONS AND SETTINGS
CONNECTIONS
DC 12 V/AC 24 V connection
Black
Red
Check for polarity when using a DC 12 V
power supply (Polarity does not matter when
using a AC 24 V power supply).
LENS ADJUSTMENTS
CAMERA SETTINGS
±180° (Pan)
VDC-C1574VA / VDC-D1584VA
Monitor checking
Screw (A)
Drop-
connector (a)
prevention
cord fixing
screw
Screw (B)
Screw
(B)
Indented
dial (C)
FOCUS
ZOOM
60 60
(Tilt)
CHECKING THE CAMERA IMAGE
You can use the monitor checking cable (sold separately) to
display an image on a monitor when setting up the camera to check
the surveillance angle and range, lens focus, etc.
Connect the connector of the monitor checking cable to the monitor
checking connector (a) on the circuit board and connect the jack
of the monitor checking cable to the monitor.
LENS ADJUSTMENTS
Once the camera has been installed, adjust the lens section.
Be careful not to touch the lens section when changing the angle
of the camera.
When loosening the drop-prevention cord fixing screw, be
careful not to loosen it too much; otherwise the dome cover may
drop.
1
Loosen the drop-prevention cord fixing screw, then adjust the pan
position (±180°) and the tilt position (±60°).
Loosen the screw (A) with a Phillips head screwdriver before
adjusting the tilt position.
2
Loosen the zoom lever screw, turn the zoom lever to the right/
left to determine the zoom position while viewing the camera
images on the monitor, and then re-tighten the screw.
3
Loosen the focus lever screw, turn the focus lever to the right/
left to determine the focus position while viewing the camera
images on the monitor, and then re-tighten the screw.
4
Tighten the drop-prevention cord fixing screw.
NOTE on image direction (Wall Installed):
If the monitor image is misaligned, follow the steps below to adjust.
Loosen the screws (B) with the supplied hexagon wrench
(small).
Turn the indented dial (C) to adjust the image direction.
Tighten the screws (B) after adjustments are finished.
Supported coaxial cables
You can use any of the following coaxial cables:
RG-59U (3C-2V) Length: 250 m (273.4 yds) max.
RG-6U (5C-2V)
Length: 500 m (546.8 yds) max.
RG-11U (7C-2V) Length: 600 m (656.2 yds) max.
When using an RG-59U (3C-2V) cable, do not attach it
to piping or wiring.
Select the cable according to the distance between the
devices you wish to connect.
If you use a cable other than the types above, the image
or sync signal will be attenuated and will not be
transmitted correctly.
VDC-W1594VA
1 2 3 4
2 3 5 4
ON
6
ON
1 2 3 4
1 2 3 4
6
7
Board on the
opposite side of the
7
lens
Monitor checking
connector (a)
DAY/NIGHT FUNCTION (VDC-D1584VA)
When connected to power, the VDC-D1584VA turns on the DAY/
NIGHT function for continuous operation.
The DAY/NIGHT function automatically switches over between
color and black-and-white mode depending on the ambient
brightness; for example, choosing color mode during daytime, and
black-and-white mode for nighttime monitoring with its increased
sensitivity in a darker environment.
NOTE:
This function is disabled if 4 is set to "Down".
CAMERA SETTINGS
The camera comes from the factory pre-adjusted and ready to
install, but you can make adjustments or settings if you need.
If you have trouble adjusting the camera, consult your dealer or an
Authorized Sanyo Service Center.
( =Factory default setting)
1 Backlight compensation setting
(VDC-C1574VA, VDC-D1584VA)
ON
Compensates for backlighting with the
centerweighted metering mode.
Down
This function is off.
NOTE:
This function is disabled if 4 is set to "Down".
If backlight compensation is not corrected in the VDC-C1574VA and
VDC-D1584VA when 1 is set to "ON", you can correct by adjusting level
volume 6.
2 Iris setting
ON
AI: Normal setting (Auto iris)
Down
EI: Electronic iris
NOTE:
This factory preset is optimal, so it is not necessary to change the
setting.
3 White balance setting
VDC-C1574VA, VDC-D1584VA
ON
ATW-A (Auto-tracing white balance - All): Automatic
setting for white balance, covering wider range of
color temperature than with "ATW".
• May result in an excessively and unnaturally
effected image, depending on the conditions.
Down
ATW (Auto-tracing white balance): Automatic setting
for white balance.
VDC-W1594VA
ON
ATW-A (Auto-tracing white balance - All): Automatic
setting for white balance, covering wider range of
color temperature than with "ATW".
• May result in an excessively and unnaturally
effected image, depending on the conditions.
Down
ATW (Auto-tracing white balance): Automatic setting
for white balance.
4 Auto Gain Control (AGC) setting
For adjusting the sensitivity of the camera. Use this setting for
shooting in dark environments.
ON
Normal setting
Down
Set this when there is excessive noise (AGC off)
SANYO INDUSTRIAL VIDEO
COLOR CCD CAMERA LIMITED WARRANTY
OBLIGATIONS
In order to obtain warranty service, the product must be delivered to and picked up from an
Authorized Sanyo Service Center at the user's expense, unless specifically stated otherwise in
this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained
by calling the toll-free number listed below.
For product operation, authorized service center referral, service assistance or problem
resolution, call
CUSTOMER INFORMATION 1-800-421-5013
Weekdays 8:30 AM – 5:00 PM Pacific Time
For accessories and/or parts, call
PARTS ORDER INFORMATION 1-800-726-9662
Weekdays 8:30 AM – 5:00 PM Pacific Time
THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN
THE UNITED STATES OF AMERICA, EXCLUDING ALL U.S. TERRITORIES AND
PROTECTORATES. THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL
PURCHASER OR END-USER. THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR
RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE
CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED.
Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO Fisher Company
warrants this SANYO product against defects in materials and workmanship for the periods
specified below. SFC will repair or replace (at its option) the product and any of its parts which fail
to conform to this warranty. The warranty period commences on the date the product was first
purchased or rented at retail.
LABOR
PARTS
IMAGE DEVICE
3 YEARS
3 YEARS
3 YEARS
5 Wide dynamic range setting (VDC-W1594VA)
Correction is made for simultaneous monitoring of subjects which
are different in brightness, one in a dark room and another in bright
outdoor environment, for example.
ON
When monitoring of subjects which differ in
brightness.
Down
This function is off.
6 Level volume
If the entire image is too dark or bright, or the backlight
compensation is not correct even after 1 is set to "ON", you need
to adjust the level volume.
Counterclockwise
Opens the lens iris, making the entire
(High)
image brighter
Clockwise
Closes the lens iris, making the entire
(Low)
image darker
7 Adjusting synchronization error
(AC 24 V users only)
Vertical sync disturbance may occur when a selector is used to
switch between multiple cameras connected to one monitor. To
prevent vertical sync disturbance, adjust 7.
VDC-C1574VA,
Press the button to eliminate sync
VDC-D1584VA
disturbances when needed.
VDC-W1594VA
Press each button to eliminate sync
disturbances when needed.
When using the DC 12V adaptor, sync setting is set to internal
sync.
EXCLUSIONS
This warranty does not cover (A) the adjustment of customer-operated controls as explained in
the appropriate model's instruction manual, or (B) the repair of any product whose serial number
has been altered, defaced or removed.
This warranty shall not apply to the cabinet or cosmetic parts, batteries or routine maintenance.
This warranty does not apply to uncrating, setup, installation, removal of the product for repair or
reinstallation of the product after repair.
This warranty does not apply to repairs or replacements necessitated by any cause beyond the
control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting
from unauthorized service or parts, improper maintenance, operation contrary to furnished
instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse,
neglect, accident, incorrect power line voltage, fire, flood or other Acts of God, or normal wear and
tear.
The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize
any party to assume for it any other obligation or liability.
SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED, WITH REGARD TO
THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS). IN
NO EVENT SHALL SFC BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY
DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO
CAUSES BEYOND ITS CONTROL. SFC'S LIABILITY FOR ANY AND ALL LOSSES AND
DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER, ARISING OUT OF OR IN
CONNECTION WITH THE SALE, USE OR OWNERSHIP OF THIS PRODUCT INCLUDING
WARRANTOR'S NEGLIGENCE, ALLEGED DAMAGED OR DEFECTIIVE GOODS, WHETHER
SUCH DEFECTS ARE DISCOVERABLE OR LATENT, SHALL IN NO EVENT EXCEED THE
PURCHASE PRICE OF THE PRODUCT.
ATTENTION
For your protection in the event of theft or loss of this product, please fill in the information below
for your own personal records.
Model No.
Serial No.
(Located on back or bottom side of unit.)
Date of Purchase
Purchase Price
Where Purchased
Advertisement
