Related Manuals for ESAB Aristo Mig 4001i
Summary of Contents for ESAB Aristo Mig 4001i
- Page 1 Origo™, Aristo® Mig 4001i Instruction manual Valid for: 833-xxx-xxxx, 852-xxx-xxxx 0460 740 001 GB 20170604...
-
Page 3: Table Of Contents
MAINTENANCE ..................... 15 Power unit ....................Welding torch.................... TROUBLESHOOTING ................... 16 ORDERING SPARE PARTS ................17 DIAGRAM ......................ORDERING NUMBERS ..................SPARE PARTS LIST..................... ACCESSORIES ....................Rights reserved to alter specifications without notice. 0460 740 001 © ESAB AB 2017... -
Page 4: Safety
Data Sheets (SDSs). Safety precautions Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or near the equipment observes all the relevant safety precautions. Safety precautions must meet the requirements that apply to this type of equipment. The following recommendations should be observed in addition to the standard regulations that apply to the workplace. - Page 5 • Protect your eyes and body. Use the correct welding screen and filter lens and wear protective clothing. • Protect bystanders with suitable screens or curtains. NOISE - Excessive noise can damage hearing Protect your ears. Use earmuffs or other hearing protection. 0460 740 001 - 5 - © ESAB AB 2017...
- Page 6 For further information contact the nearest ESAB dealer. ESAB has an assortment of welding accessories and personal protection equipment for purchase. For ordering information contact your local ESAB dealer or visit us on our website. 0460 740 001 - 6 -...
-
Page 7: Introduction
Mig 4001i is a welding power source intended for MIG/MAG welding, as well as for welding with powder filled cored wire (FCAW-S), TIG welding and for welding with coated electrodes (MMA). ESAB accessories for the product can be found in the "ACCESSORIES" chapter of this manual. Equipment Mig 4001i can be supplied with or without cooling unit. -
Page 8: Technical Data
58 V DC VRD function deactivated < 35 V VRD function activated Operating temperature -10 to +40°C Transportation temperature -20 to +55°C Constant sound pressure when idling < 70 db (A) 0460 740 001 - 8 - © ESAB AB 2017... - Page 9 Equipment marked IP23 is intended for indoor and outdoor use. Application class The symbol indicates that the power source is designed for use in areas with increased electrical hazard. 0460 740 001 - 9 - © ESAB AB 2017...
-
Page 10: Installation
S . Refer to the technical data in the scmin TECHNICAL DATA chapter. 0460 740 001 - 10 - © ESAB AB 2017... - Page 11 The mains cable areas and fuse sizes as shown above are in accordance with Swedish regulations. For other regions, supply cables must be suitable for the application and meet local and national regulations. 0460 740 001 - 11 - © ESAB AB 2017...
-
Page 12: Operation
Turning on the power source Turn on the mains power by turning switch (4) to the ”START” position. Release the switch, and it will return to the ”1” position. 0460 740 001 - 12 - © ESAB AB 2017... -
Page 13: Fan Control
For TIG welding, the welding power source is supplemented with: • a TIG torch with gas valve • an argon gas tube • an argon gas regulator • tungsten electrode 0460 740 001 - 13 - © ESAB AB 2017... -
Page 14: Mma Welding
(12 - 15 A) MMA welding For welding with coated electrodes, the power source is supplemented with: • welding cable with electrode clamp 0460 740 001 - 14 - © ESAB AB 2017... -
Page 15: Maintenance
Ensure that the filter with the finest mesh is placed towards the grille. • Reinstall the filter. Welding torch Wear parts should be cleaned and replaced at regular intervals in order to achieve trouble-free welding. 0460 740 001 - 15 - © ESAB AB 2017... -
Page 16: Troubleshooting
• Check that the welding and return cables are correctly connected. • Check that the correct current value is set. • Check that the correct wire or electrode is used. • Check the mains power supply fuses. 0460 740 001 - 16 - © ESAB AB 2017... -
Page 17: Ordering Spare Parts
Spare parts and wear parts can be ordered through your nearest ESAB dealer, see the back cover of this document. When ordering, please state product type, serial number, designation and spare part number in accordance with the spare parts list. -
Page 18: Diagram
DIAGRAM DIAGRAM 0460 740 001 - 18 - © ESAB AB 2017... - Page 19 DIAGRAM 0460 740 001 - 19 - © ESAB AB 2017...
-
Page 20: Ordering Numbers
A24 0459 839 032 Spare parts list Origo™ Mig 4001i 0460 737 0 Instruction manual Control panel A22, A24 Technical documentation is available on the Internet at: www.esab.com 0460 740 001 - 20 - © ESAB AB 2017... -
Page 21: Spare Parts List
SPARE PARTS LIST SPARE PARTS LIST Item Ordering no. Denomination 0458 398 002 Dust filter 0460 740 001 - 21 - © ESAB AB 2017... -
Page 22: Accessories
0460 565 880 Trolley with four wheels 0460 911 880 Mounting brackets 0460 946 880 Stabilizer kit for counter balance 0460 815 880 Shelf for feed unit for two wheel trolley 0460 740 001 - 22 - © ESAB AB 2017... - Page 23 0461 203 880 Installation kit water return flow guard 0465 720 002 ESAB ready mixed coolant (10 l / 2.64 gal) Use of any other cooling liquid than the prescribed one might damage the equipment. In case of such damage, all warranty undertakings from ESAB cease to apply.
- Page 24 Remote control cable 10 pole - 4 pole 0459 960 880 0459 960 881 10 m 0459 960 882 25 m Information on PSF welding torches can be found in separate brochures. 0460 740 001 - 24 - © ESAB AB 2017...
- Page 25 ACCESSORIES 0460 740 001 - 25 - © ESAB AB 2017...
- Page 26 ESAB subsidiaries and representative offices Europe THE NETHERLANDS North and South America SOUTH KOREA ESAB Nederland B.V. ESAB SeAH Corporation AUSTRIA Amersfoort ARGENTINA Kyungnam ESAB Ges.m.b.H Tel: +31 33 422 35 55 CONARCO Tel: +82 55 269 8170 Vienna-Liesing Fax: +31 33 422 35 44...
Need help?
Do you have a question about the Aristo Mig 4001i and is the answer not in the manual?
Questions and answers