Kodak I810 - Scanner Firmware - PC Installation Planning Manual
I800 series scanners
Hide thumbs
Also See for I810 - Scanner Firmware - PC:
- User manual (123 pages) ,
- User manual (86 pages) ,
- Instruction manual (25 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kodak I810 - Scanner Firmware - PC
Summary of Contents for Kodak I810 - Scanner Firmware - PC
- Page 1 i800 Series Scanners Installation Planning Guide A-61176...
- Page 2 Safety Information for Users of the Kodak i800 Series Scanners IMPORTANT: Equipment shall be installed by qualified personnel. WARNING: Dangerous voltage. Disconnect the main power before installation. WARNING: Before changing a lamp, always power down the scanner and let it cool a minimum of 10 minutes before proceeding (see Warning Labels below).
-
Page 3: Acoustic Emission
Take sufficient breaks to maintain mental alertness. Supervisors should review their practices and make compliance with these precautions a part of the job description for operation of the Kodak i800 Series Scanners or any mechanical device. Acoustic Emission Maschinenlärminformationsverordnung – 3, GSGV Der arbeitsplatzbezogene Emissionswert beträgt <70 dB(A). -
Page 4: Site Specifications
Kodak i800 Series Scanners The Kodak i800 Series Scanners are a new high speed, dual stream Introduction scanning platform consisting of four different models providing advanced image processing and superior throughput. The i800 Series Scanners are designed to handle mixed document batches for any production scanning workflow. - Page 5 Following are the physical dimensions and weight for the i800 Series Dimensions and weight Scanners (without shipping material). Height: 124 cm (49 in.) Width: 66 cm (26 in.) Depth: 127 cm (50 in.) Weight: 204 kg (450 lbs) including packaging 188 kg (414 lbs) without packaging Place the i800 Series Scanner in a location where there is sufficient Space requirements...
-
Page 6: Operating Requirements
Electrical Following are the electrical requirements for the Kodak i800 Series Scanners. requirements The scanner has a SCSI port for connection to the host computer. - Page 7 Power conditioning equipment may be required to overcome the power quality problems. Kodak can make arrangements for an on-site power analysis in an area with exceptionally unstable power. Consult with your electrical contractor or utility company to ensure that on-site wiring complies with the specifications and that wall outlets have isolated grounds and comply with codes.
- Page 8 NOTE: All data was measured in accordance with DIN 45635, ANSI S12.10-1985, and ISO 7779 in a hemi-anechoic chamber. Safety, regulatory The Kodak i800 Series Scanners conform to all applicable national and international product safety and electronic emission regulatory conformance, and requirements.
- Page 9 Supplies The following supplies are available. Order them in the United States by calling DI Supply at 1-888-247-1234 or contact your local Kodak Reseller. Outside of the United States, contact your local Kodak dealer. Description CAT No. Calibration Target (Qty 50)
-
Page 10: System Requirements
The recommended requirements for the i820/840 are needed to achieve dual-stream at the rated throughput. Testing was done with Kodak’s Scan Validation Tool using 200 dpi color and 200 dpi bi-tonal dual stream duplex, letter/A4/landscape while viewing every image. Both the TWAIN Data Source and ISIS Driver were tested. - Page 11 NOTE: All site preparation should be completed in advance of the equipment delivery. Kodak must be notified in advance of any special site requirements. These requirements include special delivery procedures, time restrictions and security clearance. The customer is responsible for inspecting the shipment and signing the Inspecting shipment Bill of Lading.
- Page 12 Do not move damaged equipment any farther than necessary (equipment should be moved no farther than an immediately adjacent area). Do not attempt any repairs until authorized by Kodak’s Equipment Customer Relations in Rochester, New York. Obtain and keep a copy of the Bill of Lading.
- Page 13 The integrator or his/her representative will conduct training for the key Training operator. A Sales and Customer Training CD, A-5611, is included with the Kodak i800 Series Scanner. This CD includes the Kodak i800 Series Scanner User Interface Software, PDF files of supporting user documentation and a training program.
- Page 14 Quick Reference Card, A-61171 hard copy Image Processing User’s Guide, A-61172 PDF file available on In the event the customer’s host computer does not meet Kodak’s Installation Warning and specifications, customer acknowledges that the i800 Series Scanners Disclaimer may not operate as efficiently and effectively as possible.
- Page 15 New equipment warranty coverage is available for DI products located within the contiguous United States; Oahu, Hawaii; Anchorage, Alaska In Canada, coverage is available within 325 road Km of a Kodak Service City; excluding Yukon and Northwest Territories, Northern Quebec, Labrador, and other remote areas.
- Page 16 4. Response Time Kodak’s objective is to provide on-site service, during Kodak’s normal working hours, within the following time frames: In the USA Distance from Kodak Within Contract Hours Service City Zone 1 (0 to 25 Miles) 4 Hours Zone 2 (26 to 50 Miles)
- Page 17 EASTMAN KODAK COMPANY Document Imaging Rochester, New York 14650 Kodak is a trademark of Eastman Kodak Company. Printed on recycled paper. DOCUMENT I M A G I N G A-61176 10/01 © Eastman Kodak Company, 2001 Printed in U.S.A.
Need help?
Do you have a question about the I810 - Scanner Firmware - PC and is the answer not in the manual?
Questions and answers