Input Port - Sony BVM-E250 Operation Manual

Menu
Dual Link HD-SDI
Composite
YC
Component
HDMI
DisplayPort

Input Port

Function and operation ([
Sets the Dual-link HD-SDI signal format when two BKM-243HS or BKM-244CC are installed
in the OPTION 1 and 2 or OPTION 3 and 4 option ports or BKM-250TG is installed.
4:2:2 YCbCr 10bit
4:4:4 YCbCr 10bit
4:4:4 RGB 10bit
4:4:4 YCbCr 12bit
4:4:4 RGB 12bit
4:4:4 XYZ 12bit
Sets the composite signal format when BKM-227W is installed.
Auto: Changes automatically according to the format of the input signal.
It will take a few seconds to detect the format of an input signal. It is recommended that
a particular format be selected if it is determined.
NTSC
PAL
PAL-M
SECAM
Sets the Y/C signal format when BKM-227W is installed.
Auto: Changes automatically according to the format of the input signal.
It will take a few seconds to detect the format of an input signal. It is recommended that
a particular format be selected if it is determined.
NTSC
PAL
PAL-M
SECAM
Sets the analog component signal format or analog RGB signal format when BKM-229X is
installed.
You can select from YPbPr or RGB.
Sets the HDMI signal format.
In this manual, the 800 × 600, 1024 × 768, 1280 × 960, 1280 × 1024 and 1400 × 1050 signals
are referred to as the HDMI computer signals.
For the signal format to be displayed, see page 114.
Sets the DisplayPort signal format.
In this manual, the 800 × 600, 1024 × 768, 1280 × 960, 1280 × 1024 and 1400 × 1050 signals
are referred to as the DisplayPort computer signals.
For the signal format to be displayed, see page 114.
Enters the input port number.
You can select from [Standard], Option1 to Option4, Option1&2 or Option3&4.
Standard
When using the standard SDI input of the monitor
• When Format is set to 3G/HD/SD-SDI Auto or 4:2:2 YCbCr 10bit, 4:4:4 YCbCr 10bit,
4:4:4 RGB 10bit, 4:4:4 YCbCr 12bit, 4:4:4 RGB 12bit or 4:4:4 XYZ 12bit of 3G-SDI
• When Format is set to HD/SD-SDI Auto
• When Format is set to SD-SDI
Option1 to Option4
When the signal is input from the input adaptor installed to the option port
• When the BKM-250TG is installed and Format is set to 3G/HD/SD-SDI Auto or 4:2:2
YCbCr 10bit, 4:4:4 YCbCr 10bit, 4:4:4 RGB 10bit, 4:4:4 YCbCr 12bit, 4:4:4 RGB 12bit or
4:4:4 XYZ 12bit of 3G-SDI
• When the BKM-243HS, BKM-244CC or BKM-250TG is installed and Format is set to HD/
SD-SDI Auto
• When the BKM-220D, BKM-243HS, BKM-244CC or BKM-250TG is installed and Format
is set to SD-SDI
• When the BKM-227W is installed and Format is set to Composite Auto, Composite
NTSC, Composite PAL, Composite PAL-M, Composite SECAM, YC Auto, YC NTSC, YC
PAL, YC PAL-M or YC SECAM
• When the BKM-229X is installed and Format is set to Component YPbPr or Component
RGB
]: factory setting)
49
Channel Configuration Menu