Welcome to the DV27 DVD player .......... 3 It may be that the DV27 has been installed and set up as part of your Safety guidelines ................4 Hi-Fi installation by a qualified Arcam dealer. In this case, you may wish Important safety instructions ............4...
Safety guidelines We do not advise the use of furniture cleaning sprays or polishes as CAUTION ATTENTION they can cause indelible white marks if the unit is subsequently wiped RISK OF ELECTRIC RISQUE DE CHOC ELECTRIQUE with a damp cloth. SHOCK DO NOT OPEN NE PAS OUVRIR 9.
TV, monitor or projector. AV control:The SCART output has a control signal that switches your TV to its SCART input when the DV27 is turned on. It will also signal to The DV27 has five video outputs: wide screen TVs the correct aspect ratio (16:9 or 4:3), provided these ...
‘multi-room’ use or routed to a tape recorder for making recordings. REMOTE CONTROL INPUT input can be used to pass RC5 code to the DV27 if it is REMOTE IN installed in a position (or system) where infrared cannot be used.
Configuring your DVD player INTRODUCTION OPERATIONAL SETUP Congratulations – if you have followed the installation instructions then the required connections to other equipment will have been made. It Operation 1/4 is now essential to go through an initial set up procedure to ensure the OSD Language English DVD player is configured correctly for use.
PROGRESSIVE PRIORITY This item is not applicable to the DV27 and should not be changed. This item is not applicable for the DV27, and should not be changed. HQ VIDEO (HIGH QUALITY VIDEO) This setting controls the type of video given out on the Component VIDEO SETUP and SCART video outputs.
Only material of parental level 1 may be played. This corresponds to MPAA rating G. This item is not applicable for the DV27, and should not be changed. Once the rating level has been set, DVD titles with parental level higher than the setting will not play.
COMPLETING THE SET-UP Complete the setup procedure by pressing on the remote SETUP control.This saves all the data and closes the setup menu.You can press at any time while in a menu to quit from it. SETUP To return to the setup menu at any time, ensure that there is no disc playing and press the button.
Basic use of your DVD player DV27 DVD PLAYER LOAD PLAY STOP PAUSE POWER Motion Adaptive Progressive Scan FAST PLAY INTRODUCTION Press on the front panel or remote control to play fast forward or backwards. For DVDs,VCDs and CDs the following speeds ‘Basic operation’...
15, press , then , then DISP (display) Standby Dims or turns the DV27’s display on or off.Turning the display off Press to toggle the standby state of the DVD player. STANDBY generally gives a slight improvement in sound quality.
The status information displayed varies depending on the type of disc – DVD, CD or VCD. SETUP ‘Setup’ allows you to configure the DV27 for use in your system. Ensure that no disc is playing and press SETUP to access the ‘Setup’...
A jump can be performed using different specifiers: jump to a particular PEFORMING AN A-B REPEAT time or to a specified chapter/track on the disc. The DV27 can repeat a specific section of a DVD or VCD; this is called TIME an A-B repeat.
TO PROGRAM A SPECIAL SEQUENCE The bottom of the screen shows the number of tracks present on the disc. Below this is an information line, giving relevant information for the cursor position. Press on the remote control to open the ‘Programme’ menu. PROG Note that playback must be stopped first.
Advanced MP3/WMA/JPEG and audio CD features The DV27 DVD player has the ability to handle MP3, WMA and JPEG When playing CD-ROMs, tag information from MP3 and WMA files, when these are burned on to a CD-R or CD-RW disc. Picture/ files is displayed here, if present on the disc.
PROG before transferring large numbers of MP3 files to CD-R or list (‘Playlist’ mode) and playback starts automatically. CD-RW for subsequent playback on the DV27. Playback can be stopped and started using the keys, STOP PLAY as normal.
The system code for the DVD player is 25 (hex. 0x19).The on/off codes are: use with my learning remote? On = 123 (hex. 0x7b) Off = 124 (hex. 0x7c) A complete list of codes can be found on our website at www.arcam.co.uk PROBLEMS WITHVIDEO OUTPUT Problem Possible cause...
Some discs are manufactured incorrectly, and are known to cause problems displayed) the disc on ARCAM (and other) DVD players. Naturally, we aim to support all discs; from time-to-time we issue software upgrades for the player that fixes new problems of which we are aware. Please contact ARCAM customer support for further details.
2 x AAA batteries Mains lead E&OE Continual improvement policy NOTE: All specification values are typical unless otherwise stated. Arcam has a policy of continual improvement for its products. This means that designs and specifications are subject to change without notice.
Arcam distributor in the country of residence. It should be sent carriage prepaid by a reputable carrier -– NOT by post. No responsibility can be accepted for the unit whilst in transit to the dealer or distributor and customers are therefore advised to insure the unit against loss or damage whilst in transit.