Table of Contents
Advertisement
other
connectors
data connectors
rLead/irdock
For use with an Arcam rLead or irDock accessory. See
page E-15 and the accessory documentation for details.
RS232 serial connector
Use with control devices having an rS232 serial
port (for example, Crestron and AMX touch screen
controllers).
network connector
This section deals with installation of the unit into an
existing home network. For
information on how to use the
AVr400's network features,
the USB socket, and for a list
of supported file types, refer
to page E-45.
networking is a large subject
and only the briefest guidelines are presented in
this handbook. Please contact your Arcam dealer
or specialist installer for more information about
introducing the AVr400 into your computer network.
Ethernet
If an Ethernet cable is connected, the AVr400 will
automatically attempt to connect to your network.
You should use CAT5 cable plugged into the rJ45 socket
labelled
on the rear panel.
ETHERNET
If your network uses static IP addressing rather than
DHCP, you will need to provide IP address, gateway,
DnS and proxy information. See page E-39 for
information on setting up the network.
USb connector
The AVr400 can play files
stored on a USB mass storage
device, typically a pen drive,
but any USB device that
complies with the 'mass storage
device' class is compatible.
The AVr400 only supports the direct connection of USB
devices and will not support devices connected through
a hub. If regular access to the
socket is required, you
USB
may find it convenient to use a USB extension lead.
See page E-45 for details of supported file types.
Trigger connectors
The trigger connectors (
and
TRiG Z1
1
) provide an electrical signal
TRiG Z2
whenever the AVr400 is switched on and
the relevant zone enabled.
The trigger signal can be used to switch
on and off compatible pieces of home
entertainment equipment, for example,
you could set up a trigger to turn on your
television and BD player whenever the
AVr400 was switched on.
There are two trigger output sockets on the AVr400,
each capable of outputting a 12V, 70mA switching
signal. The socket is designed for mono 3.5mm jacks: tip
is the trigger output, sleeve is ground.
tip: Trigger output
sleeve: ground
TRIG Z1
Use for remotely turning on and off power amps or
source equipment for Zone 1. On = 12V, Off = 0V.
TRIG Z2
Use for remotely turning on and off power amps or
source equipment for Zone 2. On = 12V, Off = 0V.
Infra-red (IR) connectors
The infra-red inputs (
and
Z1 iR
Z2 iR
the connection of external Ir receivers, either
when the AVr400 front panel Ir receiver is
fully or partially obstructed or to allow the
use of a remote control in Zone 2.
There are two Ir inputs on the AVr400, each
designed for stereo or mono 3.5mm jacks. Tip
is the modulated signal, sleeve is ground.
tip: Modulated signal
sleeve: ground
E-17
noTE
Sockets referring to 'Z2' relate to connections used
in multi-room installation. For more information on
these connectors, see page E-46.
Z1 IR
This input is intended for use with a local Ir receiver
when the front panel of the AVr400 is blocked.
Connecting an Ir receiver to
will disable to front
Z1 iR
panel Ir receiver to prevent problems with multiple
commands if the front panel Ir receiver is only partially
obstructed.
Z2 IR
This input is intended for use with an Ir receiver in
Zone 2 to allow remote control of AVr400 from a
second room.
A supplier of infra-red receivers and emitter accessories
and systems is Xantech. See
www.xantech.com
more information, or ask your Arcam dealer.
NOTE
The Ir inputs on the AVr400 are designed for
modulated signals. If the external Ir receiver
) allow
demodulates the Ir signal, it will not work. Also
the AVr400 does not provide power for external
receivers on the Ir jack, therefore an external power
source will be required.
for
Hide quick links:
Advertisement
Table of Contents
