Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Martin Exterior Wash 100
Summarization of Contents
Safety information
Protection from electric shock
Warnings and guidelines to prevent electrical hazards associated with the fixture.
Protection from burns and fire
Precautions against heat and fire risks associated with the fixture's operation.
Protection from eye injury
Warnings regarding the fixture's light output and potential eye safety hazards.
Protection from injury
General guidance on secure installation and preventing physical harm during use.
Introduction
Fixture overview
Description and identification of fixture components and their functions.
Before using the product for the first time
Essential initial steps and checks before operating the fixture for the first time.
Physical installation
Fixture location
Criteria and limitations for selecting a suitable installation site for the fixture.
Mounting the fixture
Procedures and requirements for securely attaching the fixture to a support.
Mounting on a surface
Specific instructions for surface mounting methods and required hardware.
Suspending from a truss
Guidelines for rigging and suspending the fixture from truss structures.
Adjusting tilt
Instructions for changing the fixture's vertical aiming angle.
Installing a diffuser
Steps for fitting optional lenses to modify the fixture's beam characteristics.
Installing a snoot
Procedure for attaching an optional snoot accessory to the fixture.
AC power
Protecting connections from moisture
Methods to prevent water ingress and corrosion at power connections.
Connecting to power
Detailed steps for wiring the fixture to the electrical power supply.
Installing a temporary power plug
Instructions for adding a power plug for temporary fixture use.
Control data link
Connecting the data link
How to physically connect DMX cables for fixture control and communication.
Setup
Accessing and navigating the control menus
How to enter and move within the fixture's menu system for configuration.
DMX settings
Overview of available DMX control modes for the lighting fixtures.
Selecting DMX mode in the Exterior Wash 100 and 110
Guide to choosing DMX modes for specific Exterior Wash 100/110 models.
DMX channels in the Exterior Wash 120
Explanation of DMX channel usage and structure for the Exterior Wash 120 model.
DMX addresses
Instructions on how to assign start channels for DMX control.
Programming a standalone show
Instructions for creating and running shows without external DMX control.
Manual mode
How to manually adjust fixture output levels and attributes.
Display setting
Options to configure the fixture's control panel display settings.
Display inverse
How to flip the display for easier reading when mounted upside down.
Display auto turn off
Setting the display to turn off automatically after a period of inactivity.
Automatic test
Procedure to run an internal LED performance and diagnostic test.
Fixture status
Accessing information like LED temperature and operating hours.
Fixture config
Accessing advanced configuration options for customizing fixture behavior.
Master/slave operation - important guidelines
Key principles and guidelines for synchronizing multiple fixtures.
Setting up master/slave operation
Step-by-step guide to configure master/slave operation mode.
DMX mode
Reference to the available DMX control modes for the fixtures.
Dimmer curve
Selecting different intensity response curves for DMX dimming.
Effects speed
Adjusting the transition speed between programmed effects.
White balance
Fine-tuning color mix for specific white tones on applicable models.
DMX State - behavior when no DMX or Master signal is received
Configuring fixture response to loss of DMX or Master signal.
Display lock - password protection
Enabling password protection for the control panel to prevent unauthorized access.
Control menu passwords
How to set or change user and service passwords for menu access.
Factory reset
Restoring all user settings to their default factory values.
Setup via RDM
Setting Effects Speed via RDM
Example of changing effects speed using Remote Device Management (RDM).
Maintenance
Cleaning
Guidelines for cleaning the fixture to maintain performance and longevity.
Pressure relief valve
Information on the fixture's pressure equalization valve and its service.
DMX protocol
Exterior Wash 100 and Exterior Wash 110
DMX channel assignments and functions for Exterior Wash 100/110 models.
Exterior Wash 120
DMX channel assignments and functions for the Exterior Wash 120 model.
Specifications
Physical
Fixture dimensions, weight, and physical characteristics.
Dynamic Effects
Information on intensity control and color mixing capabilities.
Control and Programming
Details on control systems, DMX, RDM compliance, and receiver types.
Optics
Specifications related to LED lifetime and available beam angles.
Construction
Details on housing materials, protection ratings, and impact resistance.
Connections
Information on power and data cable connections and entry.
Electrical
Power supply requirements, consumption, and inrush current.
Typical power and current
Specific power and current draw values at different voltages.
Thermal
Operating temperature limits and total heat dissipation.
Approvals
List of safety and regulatory certifications obtained by the fixture.
Included Items
List of components supplied with the fixture in the package.
Accessories
List of optional parts available for purchase for the fixture.
Related Items
Other products or interfaces relevant to the fixture's operation.
Ordering Information
Product codes and variations for purchasing the fixture.
Need help?
Do you have a question about the Exterior Wash 100 and is the answer not in the manual?
Questions and answers