Related Manuals for ESAB Tig 200i
Summary of Contents for ESAB Tig 200i
- Page 1 Tig 150i Tig 200i Origot TA33 Instruction manual 0459 262 201 060523 Valid for serial no. 620- -xxx- -xxxx...
-
Page 2: Table Of Contents
1 DIRECTIVE ............2 SAFETY . -
Page 3: Directive
SAFETY Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who works on or near the equipment observes all the relevant safety precautions. Safety precautions must meet the requirements that apply to this type of welding equipment. - Page 4 MALFUNCTION - - Call for expert assistance in the event of malfunction. READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING. PROTECT YOURSELF AND OTHERS! ESAB can provide you with all necessary welding protection and accessories. WARNING! Read and understand the instruction manual before installing or operating.
-
Page 5: Introduction
INTRODUCTION The Tig 150i/Tig 200i is a welding current power source intended for use with coated electrodes (MMA welding) and TIG welding. Equipment The Tig 150i/Tig 200i is supplied with a mains cable and an instruction manual. ESAB’s accessories for the product can be found on page 19. -
Page 6: Installation
Slope down time 0--10 s 0.1 s 1.0 s Gas post--flow 0--25 s 0.1 s 2.0 s Current TIG Tig 150I 3 -- 150 A 100 A Current TIG Tig 200I 3 -- 200 A 100 A Current MMA Tig 150I... -
Page 7: Mains Power Supply
A protective earth connection must be made in accordance with regulations. 5.3.1 Recommended fuse sizes and minimum cable areas Tig 150i Tig 200i Mains voltage 230 V ¦10 %, 1--phase 230 V ¦10 %, 1--fas... -
Page 8: Operation
OPERATION General safety regulations for the handling of the equipment can be found on page 3. Read through before you start using the equipment! Connections and control devices Make sure that the welding power source is connected to the correct supply voltage and that it is protected by the correct fuse rating. -
Page 9: Control Panel Ta33
Control panel TA33 The power source checks the LEDs and all segments in the display when main switch is turned on. The machine type and program version are also displayed. Mains voltage (green) LED Data display Overheating (yellow) LED Knob for setting data. Increase (+) or Decrease (- -) selected by the function pushbuttons 6.2.1... - Page 10 7.1.1 2- - stroke Gas pre--flow Slope Slope down Gas post--flow Functions when using 2- -stroke control of the welding torch. In the 2- - stroke control mode, pressing the trigger switch starts gas pre--flow (if used) and strikes the arc (1). The current rises to the set value (as controlled by the slope up function, if in operation).
- Page 11 7.1.4 LiftArct The lift arc function strikes the arc when the electrode is brought into contact with the workpiece and then lifted away from it. Striking the arc with the Lift Arc function. Step 1: the electrode is touched on to the workpiece. Step 2: the trigger switch is pressed, and a low current starts to flow.
-
Page 12: Mma Welding
Tig 150i/Tig 200i gives direct current, and you can weld most metals to alloy and non--alloy steel, stainless steel and cast iron. The Tig 150i allows you to weld most coated electrodes from ∅ 1.6 to ∅ 3.25. The Tig 200i allows you to weld most coated electrodes from ∅ 1.6 to ∅ 4.0. -
Page 13: Fault Tracing
Check that the correct electrodes are being used. Fault codes The Tig 150i/Tig 200i comes with built--in fault monitoring. If a fault occurs, a code is shown in the display. If any of these fault codes (Exx) reappears once the unit has been restarted, the welding power source should be sent to an authorised ESAB service workshop for repair. -
Page 14: Diagram
Diagram - - 14 - - Tig150i... - Page 15 - - 15 - - Tig150i...
-
Page 16: Diagram
Diagram - - 16 - - Tig200i... - Page 17 - - 17 - - Tig200i...
-
Page 18: Ordering Number
Tig 150i, Tig 200i Ordering number Ordering no. Denomination Type Notes 0459 200 881 Welding power source OrigotTig 150i, TA33 for 230 V mains voltage 0459 200 887 Welding power source OrigotTig 150I, TA33 for 230 V Australian version mains voltage... -
Page 19: Accessories
Tig 150i, Tig 200i Accessories MMA welding and return cable kit (”crocodile” type holder) ....0349 501 078 MMA welding and return cable kit (”screwe” type holder) . - Page 20 ESAB subsidiaries and representative offices Europe Asia/Pacific Representative offices NORWAY AS ESAB AUSTRIA BULGARIA CHINA Larvik ESAB Ges.m.b.H ESAB Representative Office Shanghai ESAB A/P Tel: +47 33 12 10 00 Vienna- -Liesing Sofia Shanghai Fax: +47 33 11 52 03...
Need help?
Do you have a question about the Tig 200i and is the answer not in the manual?
Questions and answers