Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Dantherm 6000
Summarization of Contents
Introduction
Overview
This is the service manual for the Dantherm DC Air Conditioner 4000/6000 series.
Target group
This service manual is designed for technicians who install and maintain the DC Air Conditioner, as well as the users of the unit.
Copyright
Copying of this service manual, or part of it, is forbidden without prior written permission from Dantherm Air Handling A/S.
Reservations
Dantherm reserves the right to make changes and improvements to the product and the service manual at any time without prior notice or obligation.
Warning
General precaution
This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities.
Warning symbols
Explains warning and caution symbols and their implications for safe use.
Personal protective equipment
Lists required PPE and emphasizes qualified personnel for installation safety.
Product description
Overall description
This section describes the overall product and its functionality.
Model overview
Lists available air conditioner models and their key specifications.
Available accessories
Shows the accessories available from the supplier for the unit.
Overall description, continued
Outdoor view
Illustrates the unit's outdoor view and labels key external components.
Outdoor part description
Details the components identified in the unit's outdoor view illustration.
Drainage
Describes the condensate drain feature that routes water away from the unit.
Overall description, continued
Indoor view
Illustrates the unit's indoor view and labels key internal components.
Indoor part description
Details the components identified in the unit's indoor view illustration.
Overall description, continued
Functionality
Shows the airflow of the air conditioner, distinguishing internal and external flows.
Internal air flow
Describes how warm internal air is drawn into and processed by the unit.
External air flow
Describes how cold external air is used to cool the condenser.
Filters
Discusses the optional pre-filter for the external air inlet to prevent debris.
Electronic control description
Introduction
Key features and operation of the electronic control system.
Warning
Safety warning regarding power supply disconnection before maintenance.
Embedded Controller
Setting basic parameters via the on-board control panel and SD card.
Control strategy
How the controller manages fans, heater, and compressor based on temperature.
Operation panel
Illustration and description of the unit's main operation panel interface.
Connections
Connections illustration
Shows the external electrical connections to the unit's controller.
External interfaces
Details specific external interface connections like RS485 and J15 ports.
Connections, continued
Options
Table detailing various connection options and their specifications.
Operation
Introduction
Unit operation via built-in panel, TTL, or SD card for parameters.
Key operation
Describes the function of the Up, Down, and Enter keys on the control panel.
Operation, continued
Navigating menu
Explains how to navigate through the unit's menus using control panel keys.
Toggle Celsius to Fahrenheit readings
How to switch between Celsius and Fahrenheit temperature units.
Operation, continued
Error list
Provides a list of error codes and their corresponding causes.
Steps in test program
Outlines the sequence of component tests performed by the unit.
Installation
Introduction
Recommends outdoor mounting flush to the wall as the primary installation method.
Installation placement
Guidance on selecting unit placement for optimal airflow and heat dissipation.
Air Con wall cut out
Provides precise dimensions for marking wall cutouts and mounting holes.
Installation, continued
Preparation
Instructions for unpacking and preparing the unit for wall mounting.
Installation
Steps for lifting and securing the unit onto brackets after wall cutouts are made.
Installation, continued
Electrical requirements
Imperative requirements for electrical connections and safety during installation.
Electrical connections
Details on routing, securing, and connecting power and other cables to the unit.
Service Guide
Preventative maintenance
Importance and recommended intervals for performing preventive maintenance.
Cleaning
Recommended procedure and required tools for cleaning the air conditioner unit.
Service Guide, continued
Inspection
Checks to perform before re-assembly and putting the unit back into service.
Test cooling circuit
Procedure for testing the cooling circuit if a problem is suspected.
Test safety shut down
Manual test procedure for the compressor's safety shut down switch.
Spare parts
Illustration, external parts
Shows available spare parts for the condenser section of the unit.
Sparepart list External
Lists external spare parts with their part numbers and descriptions.
Spare parts, continued
Illustration, internal parts
Shows available spare parts for the evaporator section of the unit.
Sparepart list Internal
Lists internal spare parts with their part numbers and descriptions.
Technical data
Introduction
General description of the units' design for reliability and electrical efficiency.
4000 btu. units
Technical data table detailing specifications for 4000 & 6000 BTU models.
Electrical schematics
Overall controller
Shows the complete controller connections, internal as well as external.
Electrical schematics, continued
Unit schematics
Shows the unit's internal electrical schematics and wiring.
Cooling schematic
Introduction
This illustration shows the cooling circuit schematic of the unit.
Declaration of conformity
Declaration of Conformity
Declares conformity with directives like UL and CSA standards.
Recycling
Guidance on proper recycling procedures for the unit to protect the environment.
Need help?
Do you have a question about the 6000 and is the answer not in the manual?
Questions and answers