Copying of this service manual, or part of it, is forbidden without prior written permission from Dantherm Air Handling A/S. Reservations Dantherm reserves the right to make changes and improvements to the product and the service manual at any time without prior notice or obligation. Table of contents This service manual covers the following main topics: Introduction .
• Proper work attire (long sleeve shirt and long pants) Please strictly observe the following: Special Skill is required to install the Dantherm products. Non-qualified personnel should not attempt any of the actions shown in this installation guide. Dantherm shall not be responsible for improper installation or any accidents, damage,...
Page 4
Overall description, continued Overall description, continued Outdoor view This illustrates the unit’s outdoor view: Introduction This illustrates the unit’s indoor view: Fig. 3 Fig. 1 Indoor part The table shows the part description for the indoor parts shown in Fig. 3: description Outdoor part The table shows the part description for the outdoor parts shown in Fig.
Electronic control description Overall description, continued This section describes key features of the electronic control and how it operates. The illustration and table below show the airflow of the Air conditioner. The two air flows Introduction Functionallity (internal/external) operate separately. External air is only used to cool down the condenser which dissipates the heat absorbed by the indoor evaporator.
Connections Connections, continued Connections This illustration shows the external connections to the controller The air conditioner can operate as a stand alone cooling system. For enhanced usage, it is illustration possible to connect an external display with keypad. See below table for options Connection Usage Specification...
Page 7
Operation Operation, continued Navigating menu Introduction The unit can operate on the built in operation panel. All operation parameters are set via TTL Menu structure and navigation. Step up/down to jump through menues, end enter to select or SD card. Cooling and heating setpoints are available in the control panel. the parameter to read or change.
DC Comp. [DCK][0/1]: 0 Ret Air Sens [RAS][0/1]: 1 Air Con 4000 Please mark the cutout area and holes, according the below dimensions: Hotspot Sens [HSS][0/1]: 0 wall cut out Evap in Sens [EIS][0/1]: 1 [8 5/8 in.]...
Page 9
Installation, continued Installation, continued Preparation Unpack the unit and place onto a table or similar stable placement. Electrical Please incorporate the following imperative requirements when installing the electrical requirements connections: The unit has small sheet metal parts that must be hand bent 90° in order for it to support the unit when attaching and securing the bolts and intalling the unit permanently to the wall.
Service Guide Preventative maintenance, continued Preventative maintenance Inspection The unit must be inspected prior to any re-assembly and put back into service. Please follow below steps: Introduction Preventive maintenance has to be performed in order to: Phase Description • Continue operation in specified range Are the fans clean and free of any corrosion? •...
3: Supply GND 2: NC Supply 1: Supply 12V Accessory 4000 btu . units This table shows the technical data for 4000 BTU models. 8: Evap out sens GND Specification Unit 115 VAC units 230 VAC units 7: Evap out sens signal...
Page 13
SPARTANBURG, SC 29303 SPARTANBURG, SC 29303 ANGLES ANGLES DANTHERM INC. ALL DESIGNS ORIGINATED BY DANTHERM INC, ARE THE PROPERTY OF DANTHERM INC. ALL DESIGNS ORIGINATED BY DANTHERM INC, ARE THE PROPERTY OF ISO 1101/ANSI Y14.5 ISO 1101/ANSI Y14.5 ALL INSIDE RADII TO BE MATERIAL THICKNESS ALL INSIDE RADII TO BE MATERIAL THICKNESS SAID COMPANY AND WILL BE PROTECTED BY PATENTS.
Electrical schematics, continued Cooling schematic Unit schematics This illustration shows the units schematics: Introduction This illustration shows the cooling circuit schematic. Compressor Condenser Evaporator Line drier Capillary tube Fig. 17 Fig. 16...
Declaration of conformity Declaration of Dantherm Air Handling A/S, Marienlystvej 65, DK-7800 Skive hereby declare that the Air Conformity Conditioners are in conformity with the following directives: UL 60335-1 ..... . Fifth Edition UL 60335-2-40 .
Need help?
Do you have a question about the 4000 Series and is the answer not in the manual?
Questions and answers