Table of Contents
Advertisement
Quick Links
SIDE-
POWER
Thruster systems
Installation and user's manual
GB
Installasjons og brukermanual
N
SLEIPNER MOTOR AS
P.O. Box 519
N-1612 Fredrikstad
Norway
Tel:
Fax:
+47 69 30 00 60
+47 69 30 00 70
SE 120/215T
SE 150/215T
w w w . s i d e - p o w e r . c o m
s i d e p o w e r @ s l e i p n e r. n o
© Sleipner Motor AS 2007
Advertisement
Table of Contents
Related Manuals for Side-Power SE 150-215T
Summarization of Contents
Technical Specifications
Motor Specifications
Details about the custom-made reversible DC-motor and its characteristics.
Gearhouse and Bracket Details
Information on the seawater resistant gearhouse and aluminium motor bracket.
Tunnel and Propeller Data
Specifications for the tunnel material and the 5-blade skewback propeller.
Battery and Usage Specifications
Recommended battery capacity and maximum continuous usage time.
Safety Features Overview
Details on electronic time-lapse devices and thermal cut-offs.
Planning and Installation Precautions
General Installation Guidelines
Installer must read guide, avoid ignition proof compartments, and ensure proper motor separation.
Mounting, Ventilation, and Handling
Ensure ventilation, correct motor angle support, and careful handling.
Environmental Protection and Safety
Protect electricals from water, use antifouling, and avoid internal tunnel coatings.
Operational Safety and Warnings
Avoid running thruster on land, near people, or flammable objects.
Tunnel and Thruster Positioning
Forward Placement Strategy
Position thruster as far forward as possible for optimal leverage and thrust.
Deep Installation Rationale
Install tunnel deep to avoid air intake and maximize propeller efficiency.
Optimal Tunnel Length
Recommended tunnel length is 2-4x diameter to minimize friction and cavitation.
Tunnel End Design
Benefits of Rounded Tunnel Ends
Rounded ends maximize thrust and minimize noise by preventing turbulence.
Hull Water Intake for Thrust
Curved ends draw water from hull sides, creating vacuum for additional thrust.
Preventing Drag from Tunnel Installation
Hull Recess Method
Create a recess at the tunnel's rear to eliminate drag and noise.
Deflector/Spoiler Application
Install a deflector in front of the tunnel to direct water flow around it.
Sailboat Tunnel Installation
Addressing Sailboat Hull Constraints
Adapting installation for flat-bottomed or shallow-draft racing hulls.
Modified Installation Method for Sailboats
Fitting tunnel halfway into hull and moulding a bulb for support.
Tunnel Installation Process (Fiberglass)
Professional Fiberglass Work Recommendation
Recommends professional installation for fiberglass work; installer responsible for faults.
Marking, Cutting, and Surface Preparation
Steps for marking tunnel position, cutting the hole, and preparing the hull surface.
Casting Tunnel to Hull Procedure
Details on casting the tunnel to the hull using glass fiber layers.
Tunnel Installation Finishing Touches
Edge Treatment for Optimal Performance
Softening tunnel edges with radius or slope for better performance and less noise.
Waterproofing External Castings
Applying topcoat/epoxy and primer to external areas to ensure water resistance.
Fitting Gearhouse and Motor Bracket
Alignment and Surface Preparation
Marking centerlines, preparing the tunnel surface for bracket attachment.
Drilling, Fitting, and Securing Components
Drilling holes, testing fit of lower unit, and securing gearhouse and bracket.
Propeller Installation
Propeller Alignment and Securing Steps
Instructions for fitting the propeller onto the shaft and securing it.
Electromotor Installation
Motor Mounting and Alignment
Steps for mounting the motor to the bracket and aligning components.
Securing, Support, and Protection
Fastening motor, providing support for angled motors, and tunnel protection.
Electrical Installation Guide
Cable, Battery, and Fuse Sizing
Guidance on selecting appropriate cable, battery, and fuse sizes.
Main Switch, Fuse, and Wiring
Instructions for installing main switch, fuses, and making electrical connections.
Pre-Connection Electrical Checks
Performing checks with an ohm meter before final connections.
Control Panel and Wiring
Control Panel Setup and Compatibility
Guidelines for installing and using Sidepower control panels.
Wiring Pin Configuration
Details on the pinout for the 4-pole AMP connector.
Visual Wiring Diagram
Electronic Control Box Connections
Schematic showing connections to the 6 1232i electronic control box.
Motor, Battery, and Switch Wiring
Diagram illustrating wiring for the motor, battery, main switch, and thermal switch.
Technical Wiring Diagram
AMP Connector Pinout and System Wiring
Detailed wiring diagram including AMP connector pinout.
Installation Checklist
Component and Connection Verification
Checks for propeller, gearhouse, electrical connections, and motor mounting.
Final Checks and Compartment Integrity
Ensuring correct installation, isolation, and absence of flooding risks.
Important User Precautions
Safety Switch and General Safety Rules
Locate main switch, turn off power before touching, and avoid operating near people.
Operational Limits and Battery Care
Understand usage limits, thermal cut-off, and importance of battery condition.
Control System Usage and Error Handling
Use one control at a time; shut down immediately if issues arise.
Operating Sidepower Thrusters
Bowthruster Operation
Instructions for turning on and operating the bowthruster using control panels.
Sternthruster and Combined Operation
Using sternthruster and combining bow/stern for enhanced maneuverability.
Maintenance and Servicing
Regular Tightening, Cleaning, and Antifouling
Retighten bolts, keep components clean, and apply antifouling.
Zinc Anode Replacement and Seasonal Checks
Replace zinc anode as needed and perform seasonal checks.
Troubleshooting Common Issues
No Thrust or Motor Operation Problems
Diagnosing issues when the motor runs but produces no thrust.
Start, Direction, and Performance Issues
Resolving problems with starting, incorrect direction, or low thruster performance.
Solenoid, Voltage, and Control Signal Problems
Addressing issues related to solenoids, low voltage, and control panel signals.
Warranty Information
Warranty Coverage and Claim Process
Details on warranty duration, what's covered, and how to make a claim.
Warranty Exclusions and Limitations
Specifies conditions and damages not covered by the warranty.
Parts List (SE 120/215 T)
Electric Motor Assembly Parts
List of components for the electric motor assembly.
Gearhouse and Bracket Parts
List of parts for the gearhouse and motor bracket.
Propeller and Drive Components
List of parts including propeller, washer, and drivepin.
Parts List (SE 150/215 T)
Electric Motor Assembly Parts
List of components for the electric motor assembly.
Gearhouse and Bracket Parts
List of parts for the gearhouse and motor bracket.
Propeller and Drive Components
List of parts including propeller, washer, and drivepin.
Service Centres Directory
Global Authorized Service Network
Directory of authorized service centres worldwide for assistance and support.
Need help?
Do you have a question about the SE 150-215T and is the answer not in the manual?
Questions and answers