Advertisement
Quick Links
This documentation and the software included with this product are
copyrighted 2001 by Advantech Co., Ltd. All rights are reserved.
Advantech Co., Ltd. reserves the right to make improvements to the
products described in this manual at any time without notice.
No part of this manual or software may be reproduced, copied,
translated or transmitted, in any form or by any means without the
prior written permission of Advantech Co., Ltd. Information provided
in this manual is intended to be accurate and reliable. However,
Advantech Co., Ltd. assumes no responsibility for its use, nor for any
infringements of rights of third parties which may result from its use.
PC-LabCard is a trademark of Advantech Co., Ltd. IBM, PC and
PC/XT/AT are trademarks of International Business Machines
Corporation. MS-DOS, MASM, QuickBASIC, Microsoft C and MS-
PASCAL are trademarks of Microsoft Corporation. Intel is a trademark
of Intel Corporation. Turbo C and Turbo PASCAL are trademarks of
Borland International.
2nd Edition
Printed in Taiwan
July 2001
Advertisement
Related Manuals for Advantech PCI-1620
Summarization of Contents
Introduction to Advantech PCI Comm Cards
Product Description
Overview of the PCI Local Bus and Advantech serial communication cards, including the 16PCI954.
Product Features
Lists the key features of the Advantech PCI Comm Card Series, such as speed and UART capabilities.
Technical Specifications
Details on bus interface, data signals, communication controllers, speed, and power requirements.
Ordering Information
Information on available PCI card models and their specific configurations.
Hardware Configuration
Initial Inspection
Guidance on checking the shipping package contents and the PCI communication card for damage.
Jumper and Switch Locations
Visual guide to the physical locations of jumpers and switches on the PCI-1601 card.
Jumper Settings and Defaults
Instructions on setting jumpers for configuration and details on default settings.
PCI Card Installation
Step-by-step instructions for physically installing the PCI card into a computer.
RS-422/485 Mode Selection
How to configure ports for RS-422 or RS-485 operation using jumpers.
Enable Mode and Terminator Resistor Setup
Configuring the enable mode and installing termination resistors for impedance matching.
Driver Setup & Installation
Overview of Driver Installation
General overview of driver installation, configuration, and removal for Windows 95/98 and NT.
Windows 95/98 Driver Setup Steps
Step-by-step guide for installing drivers on Windows 95/98, including rebooting and verification.
Windows 95/98 Driver Configuration and Removal
Guide to configuring serial devices and removing drivers/devices on Windows 95/98.
Windows NT Driver Setup Steps
Step-by-step guide for installing drivers on Windows NT.
Windows NT Driver Operation and Verification
How to start, verify, and stop device functions and services on Windows NT.
ICOM Tools
Introduction to ICOM Tools
Introduction to the Advantech ICOM Tools utility for port status analysis.
ICOM Tools Installation and Interface
Instructions for installing the utility and an overview of its user interface elements.
Port Configuration and Testing
How to configure specific ports, run tests, and stop tests using ICOM Tools.
Status and Message Area Explanations
Explanation of messages displayed on the Status Bar and Message Logo area in ICOM Tools.
Pin Assignment & Wiring
PCI-1601/1602 Pin Assignments (RS-422/RS-485)
Pinout details for PCI-1601/1602 connectors in RS-422 and RS-485 modes.
RS-422 Signal Wiring
Wiring details for the RS-422 interface, explaining full duplex connections.
PCI-1610/1612 RS-232 Pin Assignments
Pin assignments for PCI-1610/1612 cards' DB-37 and DB-25 connectors for RS-232.
PCI-1612 RS-422/485 Pin Assignments
Pin assignments for PCI-1612 cards' DB-37 and DB-25 connectors for RS-422/485.
PCI-1610/1612 RS-232 (Opt 4A) Pin Assignments
Pin assignments for PCI-1610/1612 cards' DB-9 connectors for RS-232 (Opt 4A).
PCI-1612 RS-422/485 (Opt 4A) Pin Assignments
Pin assignments for PCI-1612 cards' DB-9 and DB-25 connectors for RS-422/485 (Opt 4A).
PCI-1620 Pin Assignments
Pin assignments for the PCI-1620's DB62 connector and DB25 octopus cables.
RS-232 Wiring and Connections
Detailed wiring instructions for RS-232, including DTE/DCE and handshake options.
RS-422 Signal Wiring
Wiring specifications for RS-422 interfaces, covering full-duplex communication.
RS-485 Signal Wiring and Termination Setup
RS-485 wiring topology and guidance on installing termination resistors.
Register Structure and Format
UART Register Structure
Description of the register organization, bit significance, and addressing for the UART chip.
Baud Rate Configuration
Table mapping baud rates to their corresponding divisor values for configuration.
Detailed Register Descriptions
Explains the function of specific UART registers like ISR, FCR, LCR, MCR, LSR, and MSR.
PC I/O Address Reference
PC I/O Address Conflicts
Table of common PC I/O addresses to avoid when selecting port base addresses.
Need help?
Do you have a question about the PCI-1620 and is the answer not in the manual?
Questions and answers