Advertisement
Quick Links
FENDER FLARE
PLEASE READ AND FOLLOW THIS APPROVED INSTRUCTION CARE-
FULLY BEFORE INSTALLATION. FAILURE TO DO SO MAY CAUSE
DAMAGE TO THE VEHICLE AND WILL INVALIDATE THE WARRANTY.
PRIOR TO INSTALLATION
• Remove contents from box. Verify all parts are present and free
from any defects or damage.
• Make sure installation is done on a non-abrasive surface to avoid
scratching the flare surface.
• Pre-fit each flare to the vehicle body to ensure they suit the
profile of the vehicle.
• Remove existing decals and mud flaps on the vehicle that may
interfere with flare installation.
• Make sure all flares and fender wheel well are clean as the
presence of dirt or sand may scratch auto body paint.
• Suggest removing the tire before installation for easier access.
• Do not use any harsh abrasive detergent to clean the flare.
PAINTING
Painted flares cannot be returned. Test fit before painting. We are
not responsible for any costs that may incur if flares were painted
without test fitting.
• Clean surface to be painted with a mild detergent or grease
remover. Do not use lacquer thinner or any solvent based product.
• To achieve best result, wipe flare surface to be painted com-
pletely dry with a tack rag prior to paint.
• Use high quality polyurethane automotive paint to paint the
flares. Application of primer may be needed. Please see paint
manufacturer's specifications.
• Not recommend to paint the edge trim, but if desired, use a flex
additive.
WARNING
Dirt or debris may become lodged between flares and vehicle's
fenders causing scratching and paint wear from vehicle vibration.
TYGER is not responsible for any damage, and installation is done
with buyer's understanding that this damage may potentially
occur.
SAFETY INFORMATION
• Before driving, ensure that flare is properly secured to vehicle.
• Do not use automatic "brush-style" car wash.
• Periodically check all components for tightness.
TG-FF6D4198
Customer Support: www.TygerAuto.com/Contact
1/5
Customer Support 1-866-340-3038
Tools Required
Electric Drill
1/4" Drill
10mm Socket
Hardware Included
x24
x14
[A]
[B]
DAMAGED or MISSING PARTS?
www.TygerAuto.com/Contact
TM
1/8" Drill
Socket Wrench
x4
[C]
Advertisement
Related Manuals for Tyger TG-FF6D4198
Summary of Contents for Tyger TG-FF6D4198
- Page 1 WARNING Dirt or debris may become lodged between flares and vehicle's fenders causing scratching and paint wear from vehicle vibration. TYGER is not responsible for any damage, and installation is done with buyer's understanding that this damage may potentially occur.
- Page 2 Front Flare Installation (passenger side) STEP 1: Remove 3 factory screws from front fender wheel well. STEP 2: Position flare in place and install 3 supplied Bolts [A]. Do not tighten. STEP 3: Adjust and hold flare to sit flush against the vehicle, and use STEP 4: Remove bolts installed in Step 2 and remove flare.
- Page 3 STEP 7: Reposition flare & install 6 supplied Bolts [A] and tighten. STEP 8: Install a supplied Nylon Fastener [C] to complete front pass- enger flare installation. Rear Flare Installation STEP 10: Install 2 supplied U-clips [B] over existing holes as indicat- STEP 9: Remove 2 factory screws.
- Page 4 STEP 13: Remove bolts installed in Step 11 and remove flare. Drill 3 STEP 14: Install 2 supplied U-clips [B] over the drilled holes as indi- mounting holes over the pilot holes with 1/5" drill bit. cated. STEP 15: Reposition flare & install 6 supplied Bolts [A] and tighten. STEP 16: Install a supplied Nylon Fastener [C] to complete rear passener flare installation.
- Page 5 Customer Support: www.TygerAuto.com/Contact...
Need help?
Do you have a question about the TG-FF6D4198 and is the answer not in the manual?
Questions and answers