11415
5/27/2009
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH:
* * * * * * * * * * * * D D D D O O O O N N N N O O O O T T T T E E E E X X X X C C C C E E E E E E E E D D D D V V V V E E E E H H H H I I I I C C C C L L L L E E E E M M M M A A A A N N N N U U U U F F F F A A A A C C C C T T T T U U U U R R R R E E E E R R R R ' ' ' ' S S S S R R R R E E E E C C C C O O O O M M M M M M M M E E E E N N N N D D D D E E E E D D D D T T T T O O O O W W W W I I I I N N N N G G G G C C C C A A A A P P P P A A A A C C C C I I I I T T T T Y Y Y Y . . . . * * * * * * * * * * * *
ITEM
QTY
PART NUMBER
1
1
3/8-16 x 1 1/4 LG.
CARRIAGE BOLT
2
1
HFN3816
HEX FLANGE NUT
3
2
CM-SP7
.250 x 1.00 x 2.00" SQUARE HOLE SPACER
4
1
CM-SP48
.250 x 2.13 x 2.13" SQUARE HOLE SPACER
5
1
CM-SP18
.250 x 1.00 x 2.00" SQUARE HOLE SPACER
6
2
7/16-14 x 1 1/2
CARRIAGE BOLT
7
1
1/2-13 x 2"
HEX BOLT
8
2
7/16-14
HEX FLANGE NUT
9
1
HFN 1213
HEX FLANGE NUT
10
1
CM-438-FW
7/16 " FISHWIRE TOOL
REAR OF VEHICLE
4.313 in
DRIVER SIDE
PLASTIC UNDER BODY PANEL
CUTOUT DIAGRAM
HITCH WEIGHT:
26
LBS.
INSTALL TIME
60
PROFESSIONAL:
MINUTES
NOVICE (DIY): 125
MINUTES
INSTALL NOTES:
- NO DRILLING REQUIRED
- LOWER AND TRIM FASCIA
INSTALLATION STEPS
1) Remove (2) fascia nuts from the under body panel and lower panel from vehicle. (Nuts will be reinstalled
in step 8)
2) Trim under body panel as shown in plastic under body panel cutout diagram.
3) Fishwire 7/16" carriage bolt and spacer in through the access hole and out the mounting hole in the
passenger side frame rail. Leave fishwire attached. (See fishwire technique diagram)
4) Raise hitch into position over fishwired bolt, remove fishwire and secure with flange nut.
5) Use 3/8" and 7/16" carriage bolts, spacers and flange nuts to secure the center of the hitch to the bumper
beam tab as shown.
6) Secure driver side arm to top of tow loop using 1/2" bolt, spacer, and flange nut as shown.
7) Torque all 1/2" fasteners to 75 lb-ft, all 7/16" fasteners to 50 lb-ft, and all 3/8" fasteners to 30 lb-ft.
8) Reinstall the fascia nuts. (Nuts that were removed in step 1)
P P P P E E E E R R R R I I I I O O O O D D D D I I I I C C C C A A A A L L L L L L L L Y Y Y Y C C C C H H H H E E E E C C C C K K K K T T T T H H H H I I I I S S S S R R R R E E E E C C C C E E E E I I I I V V V V E E E E R R R R H H H H I I I I T T T T C C C C H H H H T T T T O O O O E E E E N N N N S S S S U U U U R R R R E E E E T T T T H H H H A A A A T T T T A A A A L L L L L L L L F F F F A A A A S S S S T T T T E E E E N N N N E E E E R R R R S S S S
Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
SAAB 9-3 SPORT COMBI WAGON
(ALL EXCEPT DUAL EXHAUST MODELS)
Parts List
DESCRIPTION
5.875 in
6.250 in
4.500 in
PASSENGER SIDE
9
4
7
TOOLS REQUIRED
10mm, 3/8", 7/16", 1/2" SOCKETS
RATCHET
TORQUE WRENCH
A A A A R R R R E E E E T T T T I I I I G G G G H H H H T T T T A A A A N N N N D D D D T T T T H H H H A A A A T T T T A A A A L L L L L L L L S S S S T T T T R R R R U U U U C C C C T T T T U U U U R R R R A A A A L L L L C C C C O O O O M M M M P P P P O O O O N N N N E E E E N N N N T T T T S S S S A A A A R R R R E E E E S S S S O O O O U U U U N N N N D D D D . . . .
2000
LBS. TRAILER WEIGHT &
10
2
5
8
3
BUMPER
BEAM TAB
DESIGNED FOR USE WITH
BALLMOUNT #55001 / 45501
200
LBS. TONGUE WEIGHT.
PASSENGER SIDE
FRAME RAIL
ACCESS HOLE
8
1
6
6
3
Need help?
Do you have a question about the 11415 and is the answer not in the manual?
Questions and answers