Protekt PROT-6 Instruction Manual

it is obligatory to verify the free space required beneath the user at the workplace before each occasion of use the fall arrest system, so that, in the case of a fall, there will
!
be no collision with the ground or other obstacle in the fall path. The required value of the free space should be taken from instruction manual of used equipment.
! there are many hazards that may affect the performance of the equipment and corresponding safety precautions that have to be observed during equipment utilization,
especially:
- trailing or looping of lanyards or lifelines over sharp edges,
- any defects like cutting, abrasion, corrosion,
- climatic exposure,
- pendulum falls,
- extremes of temperature,
- chemical reagents,
- electrical conductivity.
! personal protective equipment must be transported in the package (e.g.: bag made of moisture-proof textile or foil bag or cases made of steel or plastic) to protect it against
damage or moisture.
! the equipment can be cleaned without causing adverse effect on the materials in the manufacture of the equipment. For textile products use mild detergents for delicate
fabrics, wash by hand or in a machine and rinse in water. Plastic parts can be cleaned only with water. When the equipment becomes wet, either from being in use or when
due cleaning, it shall be allowed to dry naturally, and shall be kept away from direct heat. In metallic products some mechanic parts (spring, pin, hinge, etc.) can be regularly
slightly lubricated to ensure better operation.
Other maintenance and cleaning procedures should be adhered to detailed instructions stated in the manual of the equipment.
! personal protective equipment should be stored loosely packed, in a well-ventilated place, protected from direct light, ultraviolet degradation, damp environment, sharp edges,
extreme temperatures and corrosive or aggressive substances.
IT IS THE RESPONSIBILITY OF THE USER ORGANISATION TO PROVIDE THE IDENTITY CARD AND TO FILL IN THE DETAILS REQUIRED.THE IDENTITY CARD SHOULD BE FILLED IN BEFORE THE FIRST USE BY A COMPETENT
PERSON, RESPONSIBLE INTHE USER ORGANIZATION FOR PROTECTIVE EQUIPMENT.ANY INFORMATION ABOUT THE EQUIPMENT LIKE PERIODIC INSPECTIONS, REPAIRS, REASONS OF EQUIPMENT'S
WITHDRAWN FROM USE SHALL BE NOTED INTO THE IDENTITY CARD BY A COMPETENT PERSON. THE IDENTITY CARD SHOULD BE STORAGED DURING A WHOLE PERIOD OF EQUIPMENT UTILIZATION.DO NOT
USE THE EQUIPMENT WITHOUT THE IDENTITY CARD.ALL RECORDS IN THE IDENTITY CARD CAN BE FILLED IN ONLY BY A COMPETENT PERSON.
IDENTITY CARD
MODEL AND TYPE OF EQUIPMENT
REF. NUMBER
SERIAL NUMBER
USER NAME
DATE OF PURCHASE
PERIODIC EXAMINATION AND REPAIR HISTORY
REASON FOR
DATE
ENTRY PERIODIC EXAMINATION
OR REPAIR AND OTHER REVELANT INFORMATIONS
1
2
3
4
Manufacturer:
PROTEKT - Starorudzka 9 - 93-403 Lodz - Poland
tel. +4842 6802083 - fax. +4842 6802093 - www.protekt.com.pl
Notified body for EU type examination according to PPE Regulation 2016/425:
Apave Exploitation France SAS (n°0082) 6 Rue du Général Audran 92412 COURBEVOIE cedex France
Notified body for control production:
Apave Exploitation France SAS (n°0082) 6 Rue du Général Audran 92412 COURBEVOIE cedex France
DATE OF MANUF.
DATE OF PUTTING INTO OPERATION
DEFECTS NOTED, NAME AND SIGNATURE
REPAIRS CARRIED OUT OF COMPETENT PERSON
Instruction Manual
READ CAREFULLY BEFORE USE
APAVE SUDEUROPE SAS
The work positioning device PROT-6 is the component of the personal protective equipment for work positioning and prevention of falls from a height. It
complies with EN 358.
The function of the device is to prevent an occurrence of a fall from the height. PROT-6 is very useful performing works at the height on the pillars, trees,
lattice constructions. It is needful when the job you are performing require a stable work position, very often without holding on with hands.
The device PROT-6 complies with EN 358.
BASIC EQUIPMENT
twisted polyamide rope of diameter ø16 mm;
!
stainless steel adjuster of the rope length;
!
AZ017T connector mounted on the mechanism
!
rope protecting tube.
!
ATTENTION! The work positioning device PROT-6 can be equipped only with certified (according to EN 362) snap hooks.
identity label
twisted polyamide rope
ADMISSIBLE TIME OF USE
Work positioning device can be used for 5 years. After this period the device
The manufacturer's inspection can be carried out by:
- manufacturer
- or person recommended by manufacturer
PERIODIC
- or company recommended by manufacturer.
EXAMINATION
NEXT DUE DATE During this inspection the rope will be changed and will be established admissible time of device use till next manufacturer's inspection.
CONTENT OF THE DEVICE IDENTITY LABEL
PROT-6
WORK POSITIONING DEVICE
AF 206 xx
LENGTH: xx m
000003
Serial number:
02/2014
Date of manufacture:
EN 358:1999
THE EQUIPMENT
WORK
POSITIONING
Ref.: AF 206 xxx
EN 358:1999
DEVICE
is the Notify Body 0082 and is involved in the production control phase.
total length 1 m - 20 m
adjuster of the
rope protecting tube
ø1 mm 6
free ending
of the rope
must be withdrawn from use to carry out
name of the device
type of the device
reference number of the device*
number of the manufacturing series
month/year of the device manufacture
CE marking and number of a notified body
controlling manufacturing of the equipment (art. 11)
caution: read the manual
number / year of the European standard
®
the equipment conform
marking of the manufacturer or distributor
®
PROT-6
rope length
connector
AZ017T
(mounted permanently)
manufacturer's detailed inspection
*) xx - code of length
for example: xxx=03 - length 3 m
xxx=20 - length 20 m