Protekt P-01B Instruction Manual

there are many hazards that may affect the performance of the equipment and corresponding safety precautions that have to be observed during equipment utilization, especially:
!
- trailing or looping of lanyards or lifelines over sharp edges,
- any defects like cutting, abrasion, corrosion,
- climatic exposure,
- pendulum falls,
- extremes of temperature,
- chemical reagents,
- electrical conductivity.
personal protective equipment must be transported in the package (e.g.: bag made of moisture-proof textile or foil bag or cases made of steel or plastic) to protect it against damage or moisture.
!
the equipment can be cleaned without causing adverse effect on the materials in the manufacture of the equipment. For textile products use mild detergents for delicate fabrics, wash by hand or in a
!
machine and rinse in water. Plastic parts can be cleaned only with water. When the equipment becomes wet, either from being in use or when due cleaning, it shall be allowed to dry naturally, and shall
be kept away from direct heat. In metallic products some mechanic parts (spring, pin, hinge, etc.) can be regularly slightly lubricated to ensure better operation.
Other maintenance and cleaning procedures should be adhered to detailed instructions stated in the manual of the equipment.
personal protective equipment should be stored loosely packed, in a well-ventilated place, protected from direct light, ultraviolet degradation, damp environment, sharp edges, extreme temperatures and
!
corrosive or aggressive substances.
IT IS THE RESPONSIBILITY OF THE USER ORGANISATION TO PROVIDE THE IDENTITY CARD AND TO FILL IN THE DETAILS REQUIRED.
THE IDENTITY CARD SHOULD BE FILLED IN BEFORE THE FIRST USE BY A COMPETENT PERSON, RESPONSIBLE INTHE USER ORGANIZATION FOR PROTECTIVE EQUIPMENT.
ANY INFORMATION ABOUT THE EQUIPMENT LIKE PERIODIC INSPECTIONS, REPAIRS, REASONS OF EQUIPMENT'S WITHDRAWN FROM USE SHALL BE NOTED INTO THE IDENTITY CARD BY A COMPETENT PERSON.
THE IDENTITY CARD SHOULD BE STORAGED DURING A WHOLE PERIOD OF EQUIPMENT UTILIZATION.
DO NOT USE THE EQUIPMENT WITHOUT THE IDENTITY CARD.
ALL RECORDS IN THE IDENTITY CARD CAN BE FILLED IN ONLY BY A COMPETENT PERSON.

IDENTITY CARD

MODEL AND TYPE OF EQUIPMENT
REF. NUMBER
SERIAL NUMBER
USER NAME
DATE OF PURCHASE
PERIODIC EXAMINATION AND REPAIR HISTORY
REASON FOR
DATE
ENTRY PERIODIC EXAMINATION
OR REPAIR AND OTHER REVELANT INFORMATIONS
1
2
3
4
EC type examination carried out by CETE APAVE SUDEUROPE, BP 193, 13322 Marseille, France - 0082
PROTEKT, 93-403 LODZ, ul. Starorudzka 9, POLAND, TEL: (48 42) 680 20 83, FAX: (48 42) 680 20 93, www.protekt.com.pl
DATE OF MANUF.
DATE OF PUTTING INTO OPERATION
DEFECTS NOTED, NAME AND SIGNATURE
REPAIRS CARRIED OUT OF COMPETENT PERSON
Instruction Manual
READ CAREFULLY BEFORE USE
Safety harness is basic of fall arrest equipment and complies
with EN 361.

DESCRIPTION

Full body harness P-01B is made of pieces of polyamide
webbing which are sewn and connected by metal buckles.
This configuration guarantee full safety and comfort work.

BASIC EQUIPMENT

back attaching buckle - for attaching fall arrest system;
!
connecting and adjusting buckles - for comfort wearing
!
and using of harness;

SIZES

The harness P-01B is manufactured in two sizes:
- universal: M-XL
- extra large: XXL

ADMISSIBLE TIME OF USE

Safety harness can be used for 5 years counting from a date of
putting the harness into operation. After this period the harness
be withdrawn from use to carry out
inspection
.
The manufacturer's inspection can be carried out by:
- manufacturer
- or person recommended by manufacturer
- or company recommended by manufacturer.
During this inspection will be established admissible time of harness
use till next manufacturer's inspection.
The harness must be withdrawn from use immediately and destroyed
when it has been used to arrest a fall.

CONTENT OF HARNESS IDENTITY LABEL

trade mark of the device
type of the device
reference number
PERIODIC
size
EXAMINATION
NEXT DUE DATE
month/year of the device manufacture
number of the manufacturing series
number / year of the European standards
the equipment conform
CE marki n g and number of a not i f i e d body
cont r ol l i n g manufact u ri n g of t h e equi p ment (art . 11)
caution: read the manual
marking of the manufacturer
or distributor
SAFETY
THE EQUIPMENT
HARNESS
EN 361:2002 Ref.: AB 101 03
shoulder strap
connecting
and adjusting
plastic clip
of the chest
strap
must
connecting
manufacturer's detailed
and adjusting
buckle
of the thigh strap
back attaching
buckle for attaching
P-01B
fall arrest system

SAFETY HARNESS

Ref. AB 101 03
identity label
Size: M-XL
XXL
Date
of manufacture: 03/2003
Serial
number: 0000001
EN 361:2002
P-01B
front view
chest strap
thigh strap
back view