Turning On Your Tv For The First Time - Sanyo LCD-32R45F Instruction Manual

Turning on your TV for the first time

Running initial setup
Make sure that you have inserted the batteries in the
1
remote control, connected the antenna to the TV, and
connected the AC power.
2
Press (Power), then wait several seconds. The initial
Setup Wizard screen opens (only the first time you
turn on your TV).
Setup Wizard
Choose your menu language
Move
Select
3 Press 6 or 5 to select the menu language you want,
then press ENTER. The Time screen opens.
Setup Wizard
Time Zone
DST
Mode
Year
Month
Day
Time
Move
Select
4 to highlight Time Zone, press 3
Press 6 or 5
select your time zone. Pacific, Alaska, Hawaii,
Atlantic, Eastern, Central, Mountain can be
selected.
5 If your viewing area observes daylight savings time,
press 5 or 6 to highlight DST, then press 3
select On.
6
Press 5 or 6 to highlight Mode, then press 3
select Manual (to set the date/time manually), or Auto
(the date/time are automatically set by the TV signal
source, based on the time zone you selected).
If you select Manual mode, make the settings as
7
follows:
.
Press 5 or 6
to highlight Year, Month, or Day, then
press 3
or4 to adjust the setting.
.
Set the time by pressing 5
then press 3
or4
AM/PM field. Press 5
8 After the above setting, press ENTER and the Choose
your Picture Mode screen opens.
English
Fran ais ç
Español
Next
Next Previous
ENTER MENU
Time
Pacific
Off
Auto
2010
03
15
09 : 05 AM
Next
Next Previous
ENTER MENU
or 6 to highlight Time,
to highlight the hour, minute, or
or 6 to adjust the setting.
"Home mode" qualifies for ENERGY STAR,
"Store mode" is for the retail display setup.
Move
Press 6
9
ENERGY STAR) or Store Mode (for the retail display
setup), then press ENTER.
If you select Home Mode, the Choose your TV source
screen opens.
If you select Store Mode, a message stating "Are you sure you
want Store mode? Since in this mode Energy saving is not
realized" appears. Select Yes to proceed or No to exit.
Antenna
Cable
Cable/Satellite Box
Scan for channels
Move
Press 6
10
Cable/Satellite Box, depending on the type of
connection you have.
. If you are using an antenna for a standard or HD TV signal,
select Antenna.
. If your cable is connected directly to the TV (without a
or4 to
tuner box), select Cable.
. If your cable is connected to your TV through a tuner box,
select Cable/Satellite Box.
11
Press ENTER when you have made your selection. The
channel scan screen opens.
or4 to
If you selected Antenna or Cable, your TV automatically
scans for available channels in your area and stores the
channel information in the channel list. This may take several
minutes. While scanning, the TV displays a progress report.
or4 to
– OR –
If you selected Cable/Satellite Box, the auto scan is not
necessary and the screen will ask you to select the correct
input source for your set top box. Press EXIT to close the
menu.
Notes:
. During auto scan, digital programs will be scanned first, then
analog programs. When all available digital programs have
been searched, the screen will ask you to "Press MENU or
EXIT if you don't need analog channel scan." At this point you
can press EXIT to exit the analog channel scan, or just ignore
it and the TV will go on scanning.
. Channel scan can take up to 30+ minutes.
You can press EXIT at any time to stop the auto scan, but you
will need to run the auto scan again to create a channel list.
Select the corresponding video input source through the
12
INPUT SOURCE menu.
15
Setup Wizard
Choose your Picture Mode
Home Mode
Store Mode
Select Next
ENTER
or 5 to select Home Mode (qualifies for
Setup Wizard
Choose your TV source
RF CH : 0
0
Digital Channels
0
Analog Channels
Next
Select
ENTER
or 5 to select Antenna, Cable, or
Next
Previous
MENU
Previous
MENU