Subscribe to Our Youtube Channel
Related Manuals for ITRON OpenWay Riva CENTRON ACT2
Summary of Contents for ITRON OpenWay Riva CENTRON ACT2
- Page 1 Certification Exhibit FCC ID: SK9ACT2 IC: 864G-ACT2 FCC Rule Part: 15.247 ISED Canada’s Radio Standards Specification: RSS-247 TÜV SÜD Project Number: 72166854 Manufacturer: Itron, Inc. Model: ACT2 Manual...
- Page 2 Date: April 6, 2017 PIL #: Product Line: OpenWay® Riva™ CENTRON® Distribution: Itron Internal Customers Distributors / Manufacturer Reps 6 June 2012 Page 1 of 5...
- Page 3 RF signal, but provides a method to relocate the transceiver. Some signal attenuation is expected with this configuration. The assembly consists of an Itron flex coupler that fits the outer cover of the meter. This allows for attaching customer provided remote fixed antennas and cabling. See Figure 1 below for a photo of the flex coupler assembly.
- Page 4 Approved customer supplied antenna specifications Since each customer deployment will be unique with regards to the required cabling and type of antenna, the cabling and antennas will be customer provided. Note: Under ISED Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by ISED.
- Page 5 Maximum Gain: 2.0 dBi Customer supplied cabling recommendation The Itron flex antenna is supplied with an SMA male connector. Customer supplied cabling that attaches to the Itron flex antenna should meet the following specifications. RG58C Coaxial Cable, SMA Male / Female...
- Page 6 Flex Coupler for OpenWay Riva CENTRON and OpenWay CENTRON with Velcro mount separate; not adhered to the antenna Please contact your Account Manager for ordering instructions. Should you have any questions please call Itron Support at 1-877-487-6602. Steve Wright Sr. Product Manager, Electric Metering 6 June 2012...
-
Page 7: Meter Module
ACT 2 Meter Module Technical Reference Guide Effective Date: July, 2016 ACT2 Meter Module... - Page 8 Revision History The following table describes the changes to this document for each revision of the ACT 2 meter module: Revision Date Description of Change July, 2016 Initial Release ACT2 Meter Module...
-
Page 9: Regulatory Compliance
• Consult the dealer or an experienced radio/TV technician for help. • Changes or modifications to this device not expressly approved by Itron, Inc. could void the user’s authority to operate the equipment. Innovation, Science and Economic Development Canada (ISED) This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. - Page 10 General Description The Itron ACT 2 is an electricity metering module which includes a 902.4 MHz to 927.6 MHz transmitter as well as WiFi. The module operates on AC as well as DC voltage which is supplied by a host device.
- Page 11 Installation The ACT 2 module will be installed in the Itron OPENWAY RIVA CENTRON electric meter. Shown are the meter base with metrology board, the board to board connector, the ACT 2 module, the display and the inner and outer cover.
- Page 12 Install the display on the ACT 2 module by pushing metal pins of display into module connector. ACT 2 Meter Module...
- Page 13 Insert module into upper section of inner cover and connect two wired connectors to module. ACT 2 Meter Module...
- Page 14 Connect metrology and the ACT 2 module using the board to board connector. ACT2 Meter Module...
- Page 15 Install lower inner cover. ACT2 Meter Module...
- Page 16 Install outer cover. ACT 2 Meter Module...
Need help?
Do you have a question about the OpenWay Riva CENTRON ACT2 and is the answer not in the manual?
Questions and answers