Othert6Exp Functions; Trainer Function; Throttle Cut Function - FUTABA 6EXP Instruction Manual

Trainer switch (ACRO mode)
To utilize the trainer function, the appropriate trainer cord (available separately) and a second Futaba transmitter (usually
provided by your flight instructor or R/C club) will be required. When two radios are connected with the trainer cord, they are
both capable of operating the model, but it's usually best for the instructor to hold the radio that has been setup for the plane
to be flown (as it is already programmed to fly the model). When the instructor holds the trainer switch on his radio, the student
will have control. When the instructor wishes to regain control he simply releases the switch. Then he will have immediate, full
control.
If connecting the 6EXP to another 6EXP with the small, square "micro" trainer jack, use the "Micro to Micro" (MM-TC) trainer
cord (FUTM4415). If connecting the 6EXP to Futaba radios with the larger, round, "DIN" connector, use "Micro to DIN" (MD-TC)
trainer cord (FUTM4420). The T6EXP transmitter may be connected to another T6EXP, or any 4VF, 6VA Skysport, T6EXA,
FF6 - 9, 9Z, 12Z, 14MZ, FX-40 series transmitter.
To use the trainer cord:
1. It is best for the instructor to use the transmitter that is already set up for the model to be
flown.
2. If the student's radio has PCM/PPM capability, set it to PPM.
3. If the student's radio has a plug-in RF module, remove the module.
4. Collapse the student's antenna and fully extend the instructor's antenna.
5. With the transmitters off, connect the trainer cord to both radios. (On the 6EXP the trainer jack is in the center of the rear
of the case.) Do not force the plug into the transmitter and note that the plug is "keyed" so it can go in only one way.
6. Turn on the instructor's transmitter. DO NOT turn on the students transmitter it will automatically "power up," but will not
transmit a signal. Set the servo reversing and trims of the student's radio to match that of the instructor's.
7. Turn on the receiver switch in the model. Depress the trainer switch on the instructor's radio. Use the student's radio to
operate the controls (ailerons, elevator, rudder, etc.) and observe how they respond. Make any adjustments necessary to
the student's transmitter to get the controls to respond correctly.
8. Check to see that the trims are in "sync" by toggling the trainer switch back and forth a few times. The controls on the
model should remain stationary. If the controls do not remain stationary, this indicates that the trim settings on the
student's radio do not match those on the instructor's radio. Adjust the student's trims as necessary.
Note: When the instructor initially depresses the trainer switch on his transmitter, there will be a one-second delay before the
student takes control. In most situations this momentary delay will go unnoticed.
Trainer function (HELI mode, student only)
The T6EXP (HELI mode) trainer function lets you practice flying as student by connecting the T6EXP to the instructor's Futaba
transmitter.
Throttle-cut function
The throttle-cut function is intended to be used for shutting off the engine. The engine can be conveniently shut off by pressing
the "THR Cut" button. The throttle-cut feature prevents inadvertently shutting off of the engine when lowering the throttle stick
all the way (such as when coming in for a landing). Throttle-cut works only when the throttle stick is down. To set up throttle-
cut, turn on the transmitter and receiver. Actuate the throttle-cut function by rapidly depressing, then releasing the switch twice.
Observe the momentary position of the carburetor barrel on the engine. It should be fully closed (thus shutting off the engine).
If necessary, use the throttle E.P.A. (channel 3) to fully close the carburetor barrel when the throttle-cut is activated. Now use
the throttle trim to open the carburetor barrel so the engine will idle at the desired R.P.M. when the throttle stick is all the way
down.
OTHER 6EXP FUNCTIONS
33