Chint Power CPS SCA2KTL-PS1/EU Quick Installation Manual

QUICK INSTALLATION GUIDE
Single-phase Grid-tied PV String Inverter
CPS SCA�/�/�.�KTL-PS�/EU
CPS SCA�.�/�/�KTL-PSM�/EU
Version: �.�
Date: ��/��/����
SHANGHAI CHINT POWER SYSTEMS CO.,LTD
Office Site: www.chintpower.com
Customer Service Line: ���-��������-������
INSTALLATION LOCATION
�
≤��℃
≥-��℃
≤���%
%
�
DIMENSIONS Type A bracket for �K-�.�K
���
���
�K-�.�K
�K-�K
(Single MPPT) （Double MPPT）
� GROUNDING
�. According to regulations, the secondary protection grounding can' t replace the PE terminal connection of
the AC cable. Ensure that both are grounded reliably.
�. Ensure that inverter and all cables to be installed are completely powered off during whole installation and
connection. Otherwise, fatal injury can occur due to the high voltage caused from AC and DC cables.
➁ ➀
（Only take �-�.�K model as an example）
�
PACKAGE CONTENTS
A B C D
or
F G H I J
A Inverter G Removal tool for DC connector
B Mounting bracket H Removal tool for AC connector(optional)
C AC output Connector I DC terminal connector group
D File package J Expansion screw group
E Screws K �-Pin terminal
F RS��� Cover
Type B bracket for �.�K-�K
(Hole , ,
� � �
���
���
���
���.�
���
��� ��
�� ���
� �
���
�
Items Remark
Screw M� X ��mm; �.� N m
·
OT Terminal OT�-�
S S
≥
Yellow green lines
(Yellow green lines)
(PE line of AC cable)
S
is the cross-sectional area.
Note： ➀ is for WiFi/GPRS communication
➁ is for RS��� communication (For RS��� cable connection, refer to
user manual.)
�
INSTALLATION
E
�. The walls must be fireproof and non-flammable materials, otherwise there is a fire risk.
�. Before drilling holes, check whether there are electric power pipes or other pipes buried in the walls to avoid risks.
Note: The following steps are only illustrated by the type A bracket.
K
Set bracket horizontally.
Mark the holes position
on the wall.
�
Unit:mm
M� Expansion screws; �~�.�N
�
�
AC CONNECTION
or , , )
� � �
Before connecting the AC terminal, ensure that both the AC terminal and the DC terminal are powered off and
the DC SWITCH is OFF. Otherwise there is a risk of high voltage shock.
��
Note: There are two types of AC terminals.
type A
Whether you use
� �
It is recommended to use outdoor dedicated
cables with multiple copper cores.
Unit:mm ��~��mm
A B
A Diameter （ mm） ��-��
B Cross-Section
(mm²)
�
Ø：��mm; Depth: ��mm
Drill the holes.
�
m
Install the inverter.
·
�
Please refer to the object in the delivery.
B
or , tighten the waterproof nut to avoid loosening.
�
(Recommended)
�~�mm
�
Tighten three screws
and ensure each screw
cap does not exceed
the surface.
Earth
PE
�
L N Neutral
�
(Range)
≤
�
Line
�
(Recommended)
�-A
Pay attention to not too much strength to
avoid damaging the expansion tube.
Install the expansion tubes.
�
M� Security screw x�;
Tighten the screws
at both sides.
�
Type A is in usual.
Take type A as example in the following steps.
�.�~�.�N m
·
Click
Tighten nut to Insert the AC terminal.
avoid loosening.
�-A