1. Manuals
  2. Brands
  3. V-TUF Manuals
  4. Vacuum Cleaner
  5. GCX4000
  6. Operator's manual

V-TUF GCX4000 Operator's Manual

Industrial vacuum cleaner
Hide thumbs

Advertisement

Table of Contents

Version 240724 – This supersedes and should be used instead of all previous versions.
GCX4000
INDUSTRIAL VACUUM CLEANER
OPERATOR MANUAL
Please read this manual before using the GCX4000
All Errors & Omissions Excused – Specification May Change Without Notice – Please Refer to www.v-tuf.co.uk for the latest version

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GCX4000 and is the answer not in the manual?

Questions and answers

Related Manuals for V-TUF GCX4000

Summary of Contents for V-TUF GCX4000

  • Page 1 Version 240724 – This supersedes and should be used instead of all previous versions. GCX4000 INDUSTRIAL VACUUM CLEANER OPERATOR MANUAL Please read this manual before using the GCX4000 All Errors & Omissions Excused – Specification May Change Without Notice – Please Refer to www.v-tuf.co.uk for the latest version...
  • Page 2 Follow these steps BEFORE USE For dry, non- hazardous material, For wet, non- hazardous material, foam ensure the HEPA filter is correctly fitted. filter is fitted. Ensure the head is correctly fitted and the clips secure. For dry, non- hazardous material, ensure the HEPA filter is fitted. Ensure that the drain hose bung is Remove Bung from Tank correctly fitted and sealed.
  • Page 3 Fit the hose to the tank. Clicks in and swivels Floor Cleaning - Fit wand elbow Floor Cleaning - Fit wand extensions Floor Cleaning - Fit floor head Crevice tool - Fit to the hose Round Brush – Fit to hose...
  • Page 4 GCX RANGE For use with the gutter / high level cleaning kit Fit 51mm Elbow Fit extention poles Ensure Suction Gate is closed Add extension poles to your desired length...
  • Page 5 GCX RANGE Fit 135 Angled Cuff head Tighten Thumb Screw 2(Nm). Fit gutter cleaning tool/head Tighten Thumb Screw 2(Nm).
  • Page 6 GCX RANGE...
  • Page 7 VTVS7506 M8x20 filter lock insert VTVS7021M Cartridge M-Class Filter VTVS7512 Self tapping screw 5x25 VTVS7422Y SWITCH - VRS SEALED & YELLOW V-TUF 'VRS' TYPE 10AMP - fits VTVS7512 Self tapping screw 5x25 VTVS7448 PPI45 Filter 130x25x7mm VTVS7490 PLASTIC GRID L144...
  • Page 8 GCX RANGE...
  • Page 9 V-TUF Description CODE VTVS7514 Blind Rivet 4,8X17 VTVS7491 TANK CLIP/ TANK BUCKLE VTVS7489 TANK FOR GCX4000 VTVS7499 Metal ring Ø28mm - FOR SIDE INLET VACS VTVS7521 Plunger pump - FOR SIDE INLET VACS VTVS7522 Metal chain VTVS7523 Drum Gasket VTVS7150 Inlet D.67mm VTVS7524 Cork Ø67mm...

  • Page 10: General Information

    Thank you for purchasing V-TUF product. V-TUF is focused on research and development to make sure you are fully satisfied with our products. Please read this manual carefully and follow the instructions to ensure you get the best performance from this machine.

  • Page 11: Installation

    INSTALLATION Ensure that the machine has the correct filtration system fitted properly for the substance you are going to clean: • For dry non-hazardous material, ensure the HEPA filter is fitted, secure and sealed. • For wet non hazardous material, ensure that the blue sponge filter is fitted •...

  • Page 12: Maintenance

    Ensure that the machine has an up to date electrical and functional safety test and that nothing has been moved or replaced since the test was carried out. Technical Information Model GCX4000 Capacity 37 Litres 110 & 240 Volts Working Voltage...

  • Page 13: Safety Precautions

    All repairs on V-TUF products should be done by an authorised service representative. If the machine shuts down, be sure to turn off the machine and unplug it before troubleshooting.

  • Page 14: Use Of The Device

    2. Do not vacuum inflammable combustion substance (e.g.: hot ashes), explosive and toxic substances, electrostatic or substances that are dangerous for health. EXPLOSION OR POISONING HAZARD 3. Do not rest the vacuum inlet on or move this close to delicate parts of the body (eyes, ears, mouth, etc.).

  • Page 15: Troubleshooting

    Store the vacuum in a safe place where it cannot be accessed by unauthorised personnel. TROUBLESHOOTING PROBLEM PROBABLE CAUSE PROBABLE SOLUTION The machine does not No current. Check main fuse, power cord, start plug and outlet. The machine Because of overheating, After the machine suddenly stops...

  • Page 17: Maintenance Log

    MAINTENANCE LOG EQUIPMENT HISTORY SHEET Unit ____________________ Serial Number: __________________ Model: ____________________ Log all electrical and product safety and performance tests Date of last test Date of next test Inspected By Satisfactory Defects and or Date Approx Hours Run (Company, print name, sign) YES/NO remarks...
  • Page 18 NOTES...

Table of Contents