Subscribe to Our Youtube Channel
Related Manuals for Keysight Technologies N2902B
Summary of Contents for Keysight Technologies N2902B
- Page 1 Keysight N2902B Rack Mount Kit for S-Series and 9000 Series Oscilloscopes Installation Guide...
-
Page 2: Warranty
FAR 52.227-19 (June 1987) or any equivalent agency regulation or contract clause. Use, duplication or disclosure of Software is subject to Keysight Technologies’ standard commercial license terms, and non-DOD Departments and Agencies of the U.S. Government will receive no greater than Restricted Rights as defined in FAR 52.227-19(c)(1-2) (June 1987). -
Page 3: In This Guide
In This Guide This guide contains instructions for installing the Keysight N2902B Rack Mount Kit. The rack mount kit provides a support shelf and hardware for mounting Infiniium S-Series and 9000 Series oscilloscopes into Electronic Industries Association (EIA) standard 19-inch (487-mm) rack cabinets. - Page 4 Cream-colored screws Top trim plate piece Left trim Right plate trim piece plate piece Bottom trim plate piece BNC connectors Feet bracket N2902B Rack Mount Kit...
-
Page 5: Installation
The following diagram shows how to determine a rack unit. This distance is equivalent to 1 rack unit Rack units may be designated by arrows. If not, narrow hole spacing indicates start/stop point of rack unit. Rack front view Rack side view N2902B Rack Mount Kit... - Page 6 To insure proper rail nut installation, align with this nut on front of rack. Distance from uppermost nut to lowermost nut is equal to 8 rack units (picture shows only 7 rack units). Front of Rack N2902B Rack Mount Kit...
- Page 7 2 Attach the track rails to the rack using the four 10-32 pan head screws provided and a #2 Phillips screwdriver. Track rails 10-32 pan head screws N2902B Rack Mount Kit...
- Page 8 Installing the Oscilloscope into the Rack 1 Remove the two M4 screws from the rear panel of the oscilloscope. Remove screws 2 Attach the feet brackets to the oscilloscope using the two supplied M4 16mm screws. N2902B Rack Mount Kit...
- Page 9 In a later step you will attach them to the bottom trim plate BNCs. 5 Plug the power cord into the oscilloscope and route it through the back so you can plug it into a power outlet after installation. N2902B Rack Mount Kit...
- Page 10 6 Use two M4 screws to secure each foot bracket to the support tray. 7 The oscilloscope and support tray should now look like the following picture except you may have cables connected to the side panel BNCs if you chose to attach them. N2902B Rack Mount Kit...
- Page 11 11 Attach the top trim plate piece to the rack with two cream-colored pan head screws, being sure that it slides into the notch on the top of the oscilloscope. N2902B Rack Mount Kit...
- Page 12 The top trim plate fits into this notch. The oscilloscope is now fully installed and should look similar to the following picture. N2902B Rack Mount Kit...
- Page 13 • Width: 2.5 cm (0.985 in) • Height: 2.84 cm (1.12 in) • Height: 1.57 cm (0.62 in) The following diagrams show the dimensions of an Infiniium S-Series oscilloscope in an N2902B rack mount. 48.3 cm 32.8 cm 31.1 cm 23.2 cm...
- Page 14 This information is subject to change without notice. © Keysight Technologies, Inc. 2014 Printed in Malaysia Second edition, October 2014 *N2902-97002* N2902-97002 www.keysight.com N2902B Rack Mount Kit...
Need help?
Do you have a question about the N2902B and is the answer not in the manual?
Questions and answers