Table of Contents
Advertisement
Quick Links
BROBO GROUP (AUST) PTY. LTD.
8 Fowler Rd, Dandenong South
Victoria 3175, AUSTRALIA.
☏
+ 61 3 9794 8751
��
+ 61 3 9794 8792
PRODUCT & MAINTENANCE MANUAL
MANUAL MITER SAW
YOUR BROBO DISTRIBUTOR IS:
Precision Drilling Machines Tapping Machines Multi Head Drills Tool Grinders
Tool Post Grinders Machine Vices Special Production Equipment
Accessories Riveting Machines Pedestal Grinders Metal Cutting Saws Linishers
©
��
info@brobo.com.au
www.brobo.com.au
MODEL No. TNF110
A.C.N.
098 264 316
A.B.N. 42 098 264 316
Brobo Group
brobo.com.au
Advertisement
Table of Contents
Related Manuals for Brobo TNF110
Summary of Contents for Brobo TNF110
- Page 1 © A.C.N. 098 264 316 A.B.N. 42 098 264 316 BROBO GROUP (AUST) PTY. LTD. 8 Fowler Rd, Dandenong South Victoria 3175, AUSTRALIA. �� ☏ + 61 3 9794 8751 info@brobo.com.au �� + 61 3 9794 8792 www.brobo.com.au PRODUCT & MAINTENANCE MANUAL MANUAL MITER SAW MODEL No.
- Page 2 OPERATING MANUAL FOR BROBO GROUP MANUAL MITER SAW TECHNICAL SPECIFICATION CHAPTER 1: Installation of the Machine Unpacking & Handling the Machine Parts Checklist Minimum Requirements Working Area Requirement Connection to Power Source CHAPTER 2: Safety & Accident Prevention Operation of the Machine 2.1.1.
-
Page 3: Chapter 1 - Installation Of The Machine
Upon receiving the Brobo Group TNF110 Manual Miter Saw, the machine should be standing upright & positioned centrally on top of a wooden pallet. While the machine is situated on the pallet, position the forklift arms under the pallet between the runners, keeping in mind that the machine is head heavy. Move the entire unit to an accessible area as close as possible to the final location. -
Page 4: Minimum Requirements
Ensure safe work area away from clutter, combustible materials, sufficient lighting. The saw to be secured on firm weight bearing surface. Floor to be level and with non-slip properties. Allow minimum 600mm around the machine for safe access to the plant for operation, cleaning, maintenance, inspection and emergency evacuation. Brobo Group brobo.com.au... -
Page 5: Connection To Power Source
& connect it accordingly to the corresponding voltage supply. d) If the dual motor is requested, the motor is always connected to the higher voltage, unless otherwise specified prior to the order being placed. Brobo Group brobo.com.au... - Page 6 If so, twist the red mushroom button until it is released & returned to the neutral state. 4) Ensure that all electrical leads & cables (including supply leads) are maintained in a good condition & away from sharp objects. All leads should be replaced if cut, sliced or damaged in any way. Brobo Group brobo.com.au...
-
Page 7: Chapter 2 - Safety & Accident Prevention
2.1. Operation of the Machine Brobo Group TNF110 Manual Miter Saw is specifically designed to cut non-ferrous metal cross sections with solid or thin-walled profiles. Other types of material & machining are not compatible for use with the specifications of the saw. This machine involves a high-speed blade rotation; therefore extreme caution is required when operating the device. -
Page 8: Power Supply
Faulty, damaged or worn components must be replaced immediately. Earthing Systems The installation of the earthing system must comply with the requirements stated in the: IEC Standards Part 195: Earthing & Protection Against Electric Shocks 1998. Brobo Group brobo.com.au... -
Page 9: Advice For The Operator
Always keep the workplace are as clean as possible. Remove equipment, tools or any other objects from the cutting zone. Support the workpiece on both sides of the machine to prevent it falling or jamming during the cutting cycle. Brobo Group brobo.com.au... - Page 10 This could damage the blade, the specimen or be a cause for potential injury to the operator. Always turn off the machine before carrying out any repair work. Consult the Brobo Group Engineering Department in the country in which the machine was initially purchased. Brobo Group...
-
Page 11: Machine Safety Devices
& safely. The following standards listed in section 2.4.1, which are applicable to the Brobo Group TNF110 Manual Miter Saw, are those specified by the EEC Committee that governs the safety of machinery, health & safety at work, personal protection & safeguarding of the work environment. In addition, the saw also complies with the Australian Standards regarding the safeguarding &... -
Page 12: Chapter 3 - Main Functions & Operation Of The Machine
45° : 120 mm Maximum tube cutting at 90° : 150 mm Cutting angle range : 45° - 90° - 45° Width : 800 mm Length : 670 mm Height : 1600 mm Weight : 90 kg Brobo Group brobo.com.au... -
Page 13: Cutting Range
3.3. Cutting Range Brobo Group brobo.com.au... -
Page 14: Chapter 4 - Drawings, Layouts, Assembly & Spare Parts
CHAPTER 4 - Drawings, Layouts, Assembly & Spare Parts 4.1. Electrical Diagram 4.2. Pneumatic Diagram Brobo Group brobo.com.au... -
Page 15: Saw Blade Assembly
4.3. Saw Blade Assembly Brobo Group brobo.com.au... -
Page 18: Chapter 5 - Maintenance & Selection Of Consumables
The person operating & maintaining the Brobo Group TNF110 must familiarise themselves with these instructions for their own safety & that of the others, in addition to safeguarding the production of the machine. Responsibility must be taken by the user on the general maintenance & up keeping of the unit as specified in this chapter, with particular emphasis on: ... - Page 19 7) The air supply for the pneumatic air vices should be checked regularly such that it is free of any condensed water molecules & the filter should be drained frequently. 8) Ensure that the machine performs cuts perpendicular to the work surface. If not, contact Brobo Group engineering department. 1.4. Brobolube...
-
Page 20: Chapter 6 - Troubleshoot
& feed speeds can be brought up to normal values. Blade with incorrect and/or As excessive pressure is exerted on excessive fine tooth pitch the incorrect teeth profile, replace the blade with correct tooth pitch dimensions & profile. Brobo Group brobo.com.au... - Page 21 Insufficient coolant Check the coolant level & clean piping & nozzles Excessive vibrations Specimen vibrates in the vice; check that the vice clamps are position correctly & the clamping pressures are adequate Brobo Group brobo.com.au...
Need help?
Do you have a question about the TNF110 and is the answer not in the manual?
Questions and answers